Summary of the content on the page No. 1
FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/
PARA USO EN AUTOMÓVILES/SOLO PER L'UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK/
R
EN
DE
TME-M770
6.5-INCH TOUCH PANEL WIDE LCD MONITOR
• OWNER'S MANUAL
FR
Please read before using this equipment.
• BEDIENUNGSANLEITUNG
Lesen Sie diese Bedienungsanleitung bitte vor
Gebrauch des Gerätes.
• MODE D'EMPLOI
Veuillez lire avant d’utiliser cet appareil.
• MANUAL DE OPERACIÓN
ES
Léalo antes de utilizar este equipo.
• ISTRUZ
Summary of the content on the page No. 2
Summary of the content on the page No. 3
ENGLISH Contents Installation and Connections Operating Instructions Warning ........................................................... 11 WARNING Caution ............................................................ 11 WARNING .................................................. 2 Precautions ...................................................... 12 CAUTION ................................................... 3 Installation ...................................................... 13 PRECAUTIONS ....
Summary of the content on the page No. 4
WARNING DO NOT WATCH VIDEO WHILE DRIVING. WARNING Watching the video may distract the driver from looking ahead of the vehicle and cause an accident. This symbol means important instructions. Failure to heed them can result in serious INSTALL THE PRODUCT CORRECTLY SO THAT THE injury or death. DRIVER CANNOT WATCH TV/VIDEO UNLESS THE VEHICLE IS STOPPED AND THE EMERGENCY BRAKE DO NOT OPERATE ANY FUNCTION THAT TAKES IS APPLIED. YOUR ATTENTION AWAY FROM SAFELY DRIVING It is dangerous for the driver
Summary of the content on the page No. 5
CAUTION PRECAUTIONS This symbol means important instructions. Temperature Failure to heed them can result in injury or Be sure the temperature inside the vehicle is between material property damage. +45°C (+113°F) and 0°C (+32°F) before turning your unit on. HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to Fuse Replacement the product. Return it to your authorized Alpine dealer or When replacing the fuse(s), the replacement must be of FR the near
Summary of the content on the page No. 6
Basic Operation Switching the Source 1 Touch the option part of the display to display each source operation screen or source selection screen. 2 If each source operation screen is displayed, touch CONTROL on the upper right side of the screen to display the source selection screen. • The source selection screen is displayed by touching “CONTROL” as described below, depending on the current source. Main power lamp When touched while the current source is GAME, POWER (VOLUME DOWN) (VOLUME UP) AUX
Summary of the content on the page No. 7
Other Useful Features 1 Display mode selection for the display Setup Operation (DISPLAY MODE) 1 Touch the option part of the display to display Normal images are each source operation screen or source expanded uniformly in selection screen. the horizontal direction and are displayed over 2 If each source operation screen is displayed, the entire screen. WIDE touch CONTROL on the upper right side of the screen to display the source selection screen. Normal images are expanded in the 3 Touch SETUP
Summary of the content on the page No. 8
Other Useful Features 3 Rear monitor select function (AUX OUT) 9 Dimmer LOW level adjustment (DIMMER LOW LEVEL) LINK : Output the video/audio portion shown on the main monitor, to the Adjusts the LOW LEVEL (0 (MIN) to 15 rear monitor. (MAX)) of the dimmer. AUX1 : Output the AUX1 video/audio to the rear monitor. p Touch panel adjustment (SCREEN AUX2 : Output the AUX2 video/audio to the ALIGNMENT) rear monitor. Adjust if the LCD display position and touch panel position do not match. 4 Change soun
Summary of the content on the page No. 9
TM 4 Tint tone adjustment (TINT) VISUAL EQ Operation Tint tone can be adjusted from G15 (G MAX) 1 Touch the option part of the display to display to R15 (R MAX). each source operation screen or source *Adjustment cannot be made in the selection screen. NAVIGATION (RGB connection) mode. 2 If each source operation screen is displayed, 5 Contrast adjustment (CONTRAST) touch CONTROL on the upper right side of the Contrast can be adjusted from –15 (LOW) to screen to display the source selection scree
Summary of the content on the page No. 10
Other Useful Features After touching “SOURCE”, change the source When used with touch panel compatible products with the following operation. such as the IVA-D300 series/VPE-S431, sources 1) Touch “P 1/2”. connected to those products are also selectable. The screen changes to “P 2/2”. 2) Touch “ ” “ ” “ ” “ ” to select the 1 Touch the option part of the display to display desired source. Touch “ENTER
Summary of the content on the page No. 11
Operation of DVD in IVA-D300 series Touch Long touch Play from start of current chapter 2x fast reverse/8x fast reverse after 5 seconds 1 Play/pause – 2 2x fast forward/8x fast forward after 5 seconds 3 Play next chapter Slow play (from pause mode) ł PRE STOP/STOP STOP 4 – – 5 – – 6 Call out DVD menu – 7 Switch page (function guide) – 8 Move menu cursor – 9 Enter (DVD menu) – p – – q – Call out DVD top menu w Switch page (function guide) – e Operating the DVA-5210 and the DHA-S680 series 1 Touch
Summary of the content on the page No. 12
Other Useful Features • When connecting an IVA-D300 series to the TME-M770, be sure to connect it to the “AUX IN 1” connector and set the “AUX IN MODE” setting (SETUP) to “LINK”. • When connecting a DVA-5210, DHA-S680 series, etc., to the TME-M770, set the “AUX IN MODE” setting (SETUP) to “EXT.DVD”. • When connecting a TV tuner to the TME-M770, set the “AUX IN MODE” setting (SETUP) to “TV”. • The TME-M770 and other components connected to it can be operated with a separately sold remote control
Summary of the content on the page No. 13
Installation and Connections Before installing or connecting the unit, please DO NOT DAMAGE PIPE OR WIRING WHEN read the following and pages 2 and 3 of this DRILLING HOLES. manual thoroughly for proper use. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, Warning fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire. MAKE THE CORRECT CONNECTIONS. DO NOT INSTALL THE MONITOR NEAR THE Failure
Summary of the content on the page No. 14
Installation and Connections Precautions IMPORTANT Please record the serial number of your unit in • Be sure to disconnect the cable from the (–) battery the space provided below and keep it as a post before installing your TME-M770. This will permanent record. The serial number plate is reduce any chance of damage to the unit in case of a located on the rear of the monitor or on the short-circuit. bottom of the AV interface unit. • Be sure to connect the color coded leads according to the diagr
Summary of the content on the page No. 15
Installation Installing AV Interface Unit This Unit can be placed inside the trunk, on the Attaching with screws kick panel of the front passenger's seat or 1. Place the unit on the location chosen for installa- underdash. However, to avoid unnecessary tion. signal wiring, it is better to mount the Unit as 2. Mark the screw locations using the unit as a close as possible to the Display. template. DO NOT MOUNT THE INTERFACE UNIT IN 3. Drill a hole less than 3 mm in diameter. LOCATIONS EXPOSED TO
Summary of the content on the page No. 16
Installation and Connections Attaching the monitor and stand 3 Check the sticking position. 1Temporarily fasten the stand with gum tape. 2Loosen the adjustment screws, and adjust to a CAUTION safe, viewable position. Do not install the monitor near the front passenger seat air bag system. The fixed arm tilts towards the seat side. Angle adjustment • When mounting with other than the attached Mounting screw Bracket, use the attached L shape bracket depending
Summary of the content on the page No. 17
4 Remove the main unit from the stand. 5 Remove the mount from the stand and stick it to the dashboard etc.. Remove any dirt on the place to install, using the supplied cloth. Fixing screws (M4 x 12 Supplied) If the place of attachment is curved, then bend this part to match the Mount shape. • If the temperature in the car is low (Winter), then first heat up the place where you are going to stick the mount with a hairdryer etc. • Do not apply force to the mount, or expose to humidity, within 24
Summary of the content on the page No. 18
Installation and Connections Connections Make connections correctly. Improper connections may cause a fire or operation failure. Basic connection e u i r y p 9 t 1 w q 2 3 4 5 7 6 8 o ; a s d f 16-EN TOUCH PANEL WIDE LCD MONITOR E
Summary of the content on the page No. 19
• When connecting to an IVA-D300 series or VPE- 1 Parking brake lead (Yellow/Blue) S431, use the “AUX IN 1” connector. When Connect this lead to the parking brake lead connecting a rear view camera, use the “AUX IN 2”. powered when parking brake is pulled. 2 Monitor control lead (White/Pink) Connect when upgrading with touch panel compatible products such as the IVA-D300 To prevent external noise from entering the series. audio system. 34Remote control output lead (White/Brown) • Locate the unit
Summary of the content on the page No. 20
System Connections 1) 2 main units + head unit (IVA-D300 series) + expansion box (VPE-S431) + navigation (NVE- N099P, European customers only) + DVD changer (DHA-S680 series) + TV Tuner Navigation (NVE-N099P, To RGB RGB cable sold separately) output (supplied with NVE-N099P) terminal (European (European customers only) customers only) To RGB input terminal Head unit (IVA-D300 series, sold separately) To Ai-NET input connector Ai-NET cable To AV SELECTOR terminal To AUX OUT terminal AV
