Sony XR-C8100R user manual

Summary of the content on the page No. 1

XR-C8100/C8100R
SERVICE MANUAL
AEP Model
UK Model
XR-C8100R
E Model
XR-C8100
Photo : XR-C8100R
Model Name Using Similar Mechanism XR-C7200/C7200W
Tape Transport Mechanism Type MG-25D-136
SPECIFICATIONS
AM (C8100)
Cassette player section
Tuning range AM tuning interval:
Tape track 4-track 2-channel stereo
9 kHz / 10 kHz switchable
Wow and flutter 0.08 % (WRMS)
531 - 1,602 kHz
Frequency response 30 - 20,000 Hz (C8100)
(at 9 kHz step)
10 - 20,000 Hz (C8100R)
530 - 1,710 kHz
Signal-to-noise ratio
(a

Summary of the content on the page No. 2

General TABLE OF CONTENTS Outputs Line outputs (3) Power antenna relay control 1. GENERAL lead Power amplifier control Location of Controls ............................................................... 3 lead Getting Started ........................................................................ 4 Telephone ATT control Setting the Clock .................................................................... 4 lead Illumination control lead (C8100) Cassette Player ................................

Summary of the content on the page No. 3

SECTION 1 GENERAL This section extracted from XR-C8100R’s instruction manual. – 3 –

Summary of the content on the page No. 4

– 4 –

Summary of the content on the page No. 5

– 5 –

Summary of the content on the page No. 6

– 6 –

Summary of the content on the page No. 7

– 7 –

Summary of the content on the page No. 8

– 8 –

Summary of the content on the page No. 9

– 9 –

Summary of the content on the page No. 10

– 10 –

Summary of the content on the page No. 11

– 11 –

Summary of the content on the page No. 12

– 12 –

Summary of the content on the page No. 13

– 13 –

Summary of the content on the page No. 14

– 14 –

Summary of the content on the page No. 15

– 15 –

Summary of the content on the page No. 16

– 16 –

Summary of the content on the page No. 17

– 17 –

Summary of the content on the page No. 18

SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. COVER 1 claw 4 cover 3 claws 2 claw 2-2. FRONT PANEL ASSY 3 Push the bearing (L). 2 Push the bearing (R). 4 front panel assy 1 Push the button (open). – 18 –

Summary of the content on the page No. 19

2-3. SUB PANEL ASSY 4 claws 7 CN500 3 PTT 2.6x6 6 CN802 5 claw 2 PTT 2.6x6 1 PTT 2.6x6 8 sub panel assy 2-4. MECHANISM DECK 1 screws (2.6x6) (C TIGHT) 4 mechanism deck 2 CN201 3 CN250 – 19 –

Summary of the content on the page No. 20

2-5. MAIN BOARD 3 ground point screw 4 ground point screws 2 PTT 2.6x10 5 MAIN board 6 insulated plate 1 PTT 2.6x10 2-6. HEAT SINK 1 CN551 2 J10 9 heat sink 4 cord (with connector) (INVERTER) 3 PTT 2.6x10 7 PTT 2.6x10 8 PTT 2.6x10 6 cord (with connector) 5 PTT 2.6x10 (ANTENNA) – 20 –