Summary of the content on the page No. 1
ADMIRAL 36”
Range Hood
Hotte
Installation Instructions
Use and Care Guide
Instructions d’installation
Mode d’emploi et d’entretien
FAD 367 W
Summary of the content on the page No. 2
INDEX WARNINGS AND REQUIREMENTS .....................................................................................................................................3 RECOMMENDATIONS AND SUGGESTIONS......................................................................................................................6 DIMENSIONS and MAIN PARTS...........................................................................................................................................7 INSTALLATION
Summary of the content on the page No. 3
READ AND SAVE THESE INSTRUCTIONS The Installer must leave these instructions with the homeowner. The homeowner must keep these instructions for future reference and for local electrical inspec- tors’ use. READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. Alw
Summary of the content on the page No. 4
W A R N I N G Venting system MUST terminate outside the home. DO NOT terminate the ductwork in an attic or other enclosed space. DO NOT use 4" laundry-type wall caps. Flexible-type ductwork is NOT recommended. DO NOT obstruct the flow of combustion and ventilation air. Failure to follow venting requirements may result in a fire. ELECTRICAL REQUIREMENTS A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A timedelay fuse or circui
Summary of the content on the page No. 5
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Installation Work And Electrical Wiring Must Be Done By Qualified Person(s) In Accordance With All Applicable Codes And Standards, In- cluding Fire-Rated Construction. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards
Summary of the content on the page No. 6
RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION • The manufacturer will not be held liable for any damages resulting from incor- rect or improper installation. Check that the main voltage corresponds to that indicated on the rating plate fixed to the inside of the hood. The electrical supply must be properly
Summary of the content on the page No. 7
DIMENSIONS and MAIN PARTS Dimensions Components Ref. Q.ty Product Components 1 1 Hood Body, complete with: Controls, Light, Blower, Filters 2 1 Telescopic Chimney comprising: 2.1 1 Upper Section 2.2 1 Lower Section 10 1 Damper 14.1 2 Air Outlet Connection Extension 15 1 Air Outlet Connection Ref. Q.ty Installation Components 7.2.1 2 Upper Chimney Section Fixing Brackets 7.3 1 Air Outlet Connection Support 11 6 Wall Plugs
Summary of the content on the page No. 8
INSTALLATION Wall drilling and bracket fixing
Wall marking: Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the center of the area in which the hood will be installed. Draw a horizontal line at 24” above the hob. Place bracket 7.2.1 on the wall as shown about 1/16” from the ceiling or upper limit aligning the center (notch) with the vertical reference line. Mark the wall at the centers of the holes in
Summary of the content on the page No. 9
Mounting the hood body Before attaching the hood body, tighten the two screws Vr lo- cated on the hood body mounting points. Hook the hood body onto the screws 12a. Fully tighten support screws 12a. Adjust screws Vr to level the hood body. Note: The Hood body should be secured to wall studs. If neces- sary, install a wood support behind the dry wall, flush mounted between 2 studs. This will provide the necessary structure and support for mounting. Connections DUCTED
Summary of the content on the page No. 10
ELECTRICAL CONNECTION Remove the cover from the Field Wiring Compartment with a phillips screwdriver. Feed the Power Supply Cable through the electrical knockout.
Connect the Power Supply Cable to the range- hood cable. At- tach the Power Supply Cable grounding lead to the green screw provided. Attach the White lead of the power supply to the White lead of the rangehood with a twist-on type wire connec- tor. Attach the Black lead of t
Summary of the content on the page No. 11
USE Control board Key Function Display A Switches the blower motor on and off at the Indicates the selected speed. latest selected speed Decreases the vent speed. B C Increases the vent speed. By pressing this key it is possible to activate D HI appears. The spot down on the right side the intensive speed from any previously se- flashes once a second. lected speed. The intensive speed can be acti- vated even when the motor is OFF. This speed has been timed at 10
Summary of the content on the page No. 12
CARE REMOTE CONTROL (OPTIONAL) This range hood can be controlled by a multi-function remote control available through your local Franke Dealer. Metal grease filters Filters can be washed in the dishwasher. They need to be washed when FF-sign appears on the display or in any case every 2 months, or even more frequently in case of particularly intensive use of the hood. Alarm reset Switch off the hood and the lights. If the 24h-function has been activated this has to be deactiva
Summary of the content on the page No. 13
Charcoal filter (ductless version) This filter cannot be washed or regenerated. It must be replaced when the EF appears on the display or at least once every 4 months. Activation of the alarm signal In the recycling version hoods the filter saturation alarm must be activated during the instal- lation or later. Switch off the hood and the lights. Disconnect the hood from the main voltage supply. After restoring the connection press and hold B-key. When releasing the key two
Summary of the content on the page No. 14
TABLE DES MATIÈRES AVERTISSEMENT ET CONDITIONS N ÉCESSAIRES ......................................................................................................15 CONSEILS ET SUGGESTIONS ..........................................................................................................................................18 DIMENSIONS et PRINCIPALES PIÈCES............................................................................................................................19 INSTA
Summary of the content on the page No. 15
LIRE ET CONSERVER CES INSTRUCTIONS L’installateur doit laisser ces instructions au propriétaire. Le propriétaire doit conserver ces instructions en vue d’une utilisation subséquente et pour le bé- néfice de l’inspecteur en électricité. LISEZ BIEN CETTE FICHE AVANT D’UTILISER LA HOTTE AVERTISSEMENT – POUR MINIMISER LE RISQUE D’UN FEU DE GRAISSE SUR LA CUISI- NIÈRE : Ne jamais laisser un élément de la surface fonctionner sans surveillance à la puissance de chauffage maximale; un renversemen
Summary of the content on the page No. 16
AVERTISSEMENT Le système d’évacuation DOIT se terminer à l’extérieur. N’ÉVACUEZ PAS le conduit dans un grenier ou dans tout autre espace fermé. N’UTILISEZ PAS un clapet de sécheuse à 4 pouces. ON DÉCONSEILLE l’emploi de conduit d’évacuation flexible. N’ENCOMBREZ PAS la circulation d’air. Le fait de ne pas respecter ces avertissements pourrait occasionner un incendie. FICHE TECHNIQUE ÉLECTRIQUE Le raccordement électrique doit se faire avec un circuit séparé de 15 amp
Summary of the content on the page No. 17
AVERTISSEMENT – POUR MINIMISER LES RISQUES D’INCENDIE, CHOC ÉLECTRI- QUES OU BLESSURES, OBSERVER CETTE RÈGLE : l’installation et le raccordement électrique ne doivent être effectués que par un technicien(s) qualifié, selon tous les codes municipaux. Afin d’obtenir un rendement maximal en ce qui a trait à la combustion ainsi qu’à l’évacuation des gaz par la conduite de cheminée et pour qu’il n’y ait pas de reflux des gaz de combus- tion, une bonne aération est nécessaire pour tous les ap
Summary of the content on the page No. 18
CONSEILS ET SUGGESTIONS Les instructions d’utilisation s’applique à plusieurs versions de ce type d’appareil. En conséquence, il est possible que vous trouviez des descriptions de caractéristiques ne s'appliquant pas à votre appareil. INSTALLATION Le fabricant décline toute responsabilité en cas de dommage dû à une installa- tion inadéquate ou non conforme aux règles de l’art. Vérifiez que la tension du secteur correspond à la valeur qui figure sur la pla- quette apposée à l’inté
Summary of the content on the page No. 19
DIMENSIONS et PRINCIPALES PIÈCES Dimensions Composantes Ref. Qté Pièces du produit 1 1 Corps de la hotte équipé de : commandes, lumière, groupe ventilateur, filtres 2 1 Cheminée télescopique formée de : 2.1 1 Cheminée supérieure 2.2 1 Cheminée inférieure 10 1 Clapet anti-reflux 14.1 2 Rallonges de raccord de sortie d’air 15 1 Raccord de sortie d’air Ref. Qté Pièces servant à l’installation 7.2.1 2 Brides de montage de la chemi
Summary of the content on the page No. 20
INSTALLATION Perçage de la paroi et fixation des brides
Tracer sur la paroi une ligne verticale allant jusqu’au plafond ou à la limite supérieure, au centre de la zone prévue pour l’installation de la hotte. Tracer une ligne horizontale à 24 pop. au-dessus du plan de cuisson. Poser comme indiqué une bride 7.2.1 sur la paroi à 1/16 pop. du plafond ou de la limite su- périeure, en alignant son centre (encoche) sur la ligne verticale de repère.
