Broan 350BK user manual

Summary of the content on the page No. 1

MODELS 350 • 350BK • 350BR • 355 • 355BK • 355BR
356 • 356BK • 356BR • 358
Page 1
ROOF-MOUNT
POWERED ATTIC VENTILATOR
READ AND SAVE THESE INSTRUCTIONS
CAUTION
WARNING
1. For general ventilating use only. Do not use to exhaust hazard-
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
ous or explosive materials and vapors.
TO PERSONS, OBSERVE THE FOLLOWING:
2. To avoid motor bearing damage and noisy and/or unbalanced
1. Use this unit only in the manner intended by the manufacturer.

Summary of the content on the page No. 2

MODELS 350 • 350BK • 350BR • 355 • 355BK • 355BR 356 • 356BK • 356BR • 358 Page 2 3. Drill a guide hole through the roof at this mark. 1. Locate the ventilator at the center of the rear slope of the roof. Place it as high on the roof as possible. The location should be free of obstacles (T.V. leads, electrical lines, etc.) If the ventilator top is level with the roof peak, it can't be seen from the street. Keep this approximate location in mind as you work from within the attic. 4. Cut ou

Summary of the content on the page No. 3

MODELS 350 • 350BK • 350BR • 355 • 355BK • 355BR 356 • 356BK • 356BR • 358 Page 3 6. Cut out the shingles inside of the circle. 9. Cut out the roof board(s) inside of the line. 10. For proper removal of roofing nails, draw a 22" square, 7. Replace template over guide hole and draw a 14-3/8" centered around the hole. Remove nails holding shingles diameter circle on the black paper or roof boards using down from top two-thirds of square. the smaller half of the template. 11. Slide the flashi

Summary of the content on the page No. 4

MODELS 350 • 350BK • 350BR • 355 • 355BK • 355BR 356 • 356BK • 356BR • 358 Page 4 12. Carefully lift shingles and nail flashing securely to the 13. Using a good grade of roofing cement material, seal all roof using galvanized roofing nails. of the shingles and heads of nails. DO NOT seal the bottom edge of the flashing.

Summary of the content on the page No. 5

MODELS 350 • 350BK • 350BR • 355 • 355BK • 355BR 356 • 356BK • 356BR • 358 Page 5 BLACK 1. Remove the thermostat wiring box cover plate. Bring the power THERMOSTAT cable at least 6" into the ventilator wiring box. Fasten power RED cable to box with appropriate connector. BLACK TO MOTOR GROUND TO MOTOR BLACK SWITCH BOX TO HUMIDISTAT VENTILATOR THERMOSTAT MOTOR WHITE WIRING BOX BLACK BLACK WHITE GROUND TO GROUND TO SWITCH BOX SWITCH BOX MOTOR BLACK RED TO THERMOSTAT HUMIDISTAT VENTILATOR GROUND

Summary of the content on the page No. 6

MODELS 350 • 350BK • 350BR • 355 • 355BK • 355BR 356 • 356BK • 356BR • 358 Page 6 SERVICE PARTS KEY PART DESCRIPTION NO. NUMBER 1 99150493 #8B-18 x 1/2 Sheet Metal Screw* (3 Required) 2 99110689 Plastic Dome (Models 350, 355, 356) 99111463 Plastic Dome, Black (Models 350BK, 355BK, 356BK) 99111462 Plastic Dome, Brown (Models 350BR, 355BR, 356BR) 98005419 Aluminum Dome (Model 358) 3 97006971 Fan Blade with Setscrew 4 97009316 Motor (M

Summary of the content on the page No. 7

MODELS 350 • 350BK • 350BR • 355 • 355BK • 355BR 356 • 356BK • 356BR • 358 Page 7 SERVICE PARTS Replacement parts can now be ordered on our website. Please visit us at www.Broan.com

Summary of the content on the page No. 8

MODELS 350 • 350BK • 350BR • 355 • 355BK • 355BR 356 • 356BK • 356BR • 358 Page 8 WARRANTY BROAN-NUTONE ONE YEAR LIMITED WARRANTY Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. D