Summary of the content on the page No. 1
DK 1160
DK 1190
Dunstabzugshaube
Afzuigkap
Hotte aspirante
Cooker Hood
Montage- und Gebrauchsanweisung
Installatie- en gebruiksaanwijzing
Notice et d’utilisation et d’installation
Operating and Installation Instructions
Summary of the content on the page No. 2
Contents Safety warnings 64 for user 64 for kitchen unit installer 64 Introduction 66 Extractor version 66 Filter Version 67 Hood Operation 68 Maintenance and care 70 Metal grease filter 70 Open the metal grease filter 70 Carbon filter 71 Changing the light bulb 72 Cleaning 73 Special accessories 73 Technical assistance service 73 Guarantee conditions 74 Technic Details 76 Mounting accessories included 76 Electrical connection 77 Safety warnings for the electrician 77 Wall unit mounting 78 64
Summary of the content on the page No. 3
Safety warnings for user Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. Also, when frying, keep the deep frying pan on the cooker top/ cooker under careful control. The hot oil in the frying pan might ignite due to overheating. The risk of self-ignition increases when the oil being used is dirty. It is extremely important to note that overheating can cause a fire
Summary of the content on the page No. 4
When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole. National and regional building regulations impose a number of restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas fires, in the same room. Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment comb
Summary of the content on the page No. 5
Introduction Extractor version The hood is supplied as an extractor unit and can also be used with a filtering function by fitting one activated carbon filter (special accessory). You will need original AEG carbon filter for this function (see Special Accessories). The air is discharged to the outside through a pipe, which must be fitted to connection flange D. Fig. 1. Fix the deflector with two screws Ø3,5x6,5. Fig. 2. D Fig. 1 67
Summary of the content on the page No. 6
Filter Version The air is filtered through an activated charcoal filter and returned to the kitchen through the top grill of the outlet pipe. You will need an original AEG KF20 activated carbon filter for the filtering function. (See Special Accessories). Fix the deflector using 2 screws Ø 3,5x6.5 mm. Fig. 2. Fig. 2 68
Summary of the content on the page No. 7
Hood Operation The hood is fitted with one motor having several speed. Turn the hood on a few minutes before you start cooking then you will get an underpressure in the kitchen. It should be left on after cooking for about 15 minutes or until all odours have disappeared. The control switches are located on the unit’s front panel: the light switch switches the hood lamp on and off; the motor switch switches the cooking smoke and vapour extrac- tor motor on and off, enabling you to select on
Summary of the content on the page No. 8
Maintenance and care The hood must always be disconnected from the mains power supply before beginning any maintenance work. Metal grease filter The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Open the metal grease filter Push it towards
Summary of the content on the page No. 9
Carbon filter The carbon filter should only be used if you want to use the hood in its filtering function. To do this you will need an original AEG activated carbon filter (see special accessories). This filter cannot be cleaned or reused. As a general rule, the activated carbon filter should be changed once every four months. Mounting — Fig. 5 Fit one carbon filter on the left and one on the right so to cover the plastic grids that protect the fan wheel, then turn clockwise the centra
Summary of the content on the page No. 10
Warning Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Changing the light bulb Disconnect the cooker hood from the main supply. Remove the lamp cover. Fig. 6. Replace the old
Summary of the content on the page No. 11
Cleaning Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor’s protective grid. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will
Summary of the content on the page No. 12
Guarantee conditions Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation.The guarantee does not cover commercial use. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials. The guarantee does not cover appliances where
Summary of the content on the page No. 13
Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home.They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Senlis +33 (0) 44 62 29 29 Germany Nürnberg +49 (0) 911 323 2600 Italy Pordenone +39 (0) 1678 47053 Sweden Stockholm +46 (0) 8 738 7910 UK Slough +44 (0) 1753 219899 75
Summary of the content on the page No. 14
Technic Details Models: DK 1160 DK1190 Dimensions (in cm): Height 87,5-111,6 87,5-111,6 Width 59,8 89,8 Depht 51,5 51,5 Maximum absorbed power: 250 W 250 W Motor absorption: 170 W 170 W Lighting: 2 x 40 W 2 x 40 W Lenght of the cable: 135 cm 135 cm Mounting accessories included 1 deflector 1 chimney support 2 grids 2 hooks 4 wood-screws 5 x 45 mm 4 wall plugs Ø 8 mm 2 metal screws 3,5 x 6,5 2 metal screws 3 x 9 76
Summary of the content on the page No. 15
Electrical connection Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board. When installing, an omnipolar disconnector
Summary of the content on the page No. 16
Wall unit mounting - Fig. 7 Put the template onto the wall (1) and drill two Ø12mm holes (2). Fit two hooks (3) on the drilled holes. Hang the hood on the hooks and adjust the position of the hood using the two screws on the bottom of the hooks (5). Remove the metal filters (4) and mark two points (6). Remove the hood and drill two Ø8mm holes on the marked points. Fit two Ø8mm wall dowels (7), Hang again the hood and fix the hood definitively with two screws 5X45 (8). Fix the chimney s
Summary of the content on the page No. 17
Ø 120 mm Fig. 7 79
Summary of the content on the page No. 18
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.de © Copyright by AEG LI1USB Ed.03/02
