Summary of the content on the page No. 1
3-065-583-11 (1)
Video Cassette
Recorder
Operating Instructions
PAL NTSC
SLV-ED313ME/MJ/SG
SLV-ED215PS/TH
SLV-ED115PS
© 2001 Sony Corporation
01GB01COV-ED313.p65 1 10/1/01, 14:23
SLV-ED313ME_GB 3-065-583-11 (1)
Summary of the content on the page No. 2
Caution WARNING Television programmes, films, video tapes and To prevent fire or shock hazard, do not expose other materials may be copyrighted. the unit to rain or moisture. Unauthorized recording of such material may To avoid electrical shock, do not open the be contrary to the provisions of the copyright cabinet. Refer servicing to qualified personnel laws. Also, use of this recorder with cable only. television transmission may require The mains lead must only be changed at a authorization fr
Summary of the content on the page No. 3
Getting Started Table of contents Getting Started 4 Step 1: Unpacking 5 Step 2: Setting up the remote commander 6 Step 3: Connecting the VCR 7 Step 4: Tuning your TV to the VCR 9 Step 5: Selecting a language 10 Step 6: Presetting channels 16 Step 7: Setting the clock Basic Operations Additional Operations 18 Playing a tape 38 Playing/searching at various speeds 21 Recording TV programmes 39 Setting the recording duration 24 Recording TV programmes using time the Easy Timer function 40 Checking/c
Summary of the content on the page No. 4
Getting Started Step 1 Unpacking Check that you have received the following items with the VCR: • Remote commander • Aerial cable • R6 (size AA) batteries • Plug adaptor (for SLV-ED313ME/MJ only) Checking your model name The instructions in this manual are for the six models: SLV-ED313ME, ED313MJ, ED313SG, ED215PS, ED215TH and ED115PS. Check your model name by looking at the rear panel of your VCR. SLV-ED313ME is the model used for illustration purpose. Any difference in operation is clearly in
Summary of the content on the page No. 5
Getting Started Step 2 Setting up the remote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position. Using the remote commander You can use this remote Remote sensor commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your S
Summary of the content on the page No. 6
Step 3 Connecting the VCR Connect the aerial to your VCR and TV as shown below to watch TV programmes and VCR pictures on your TV. In addition, if your TV has audio/video (A/V) input jacks, we recommend you connect the VCR to your TV using an audio/video cable to get a better picture and sound. Connecting the aerial AERIAL IN AERIAL OUT Mains lead AERIAL IN to mains : Signal flow Aerial cable (supplied) 1 Disconnect the aerial cable from your TV AERIAL and connect it to AERIAL IN on the rear IN
Summary of the content on the page No. 7
Getting Started Step 4 Tuning your TV to the VCR If you have connected your VCR to the TV using the audio/video cable, skip this step. ?/1 ON/STANDBY RF CHANNEL PROGRAM +/– ON/STANDBY 1 Press ?/1 ON/STANDBY to turn on the VCR. 2 Press RF CHANNEL on the VCR. The factory-preset RF channel flashes in the display window for RF CHANNEL about three seconds. (RF32 is for SLV-ED313ME/MJ/SG and RF51 is for SLV-ED215PS/TH and SLV-ED115PS) Press RF CHANNEL again while the RF channel is flashing. The VCR si
Summary of the content on the page No. 8
Step 4: Tuning your TV to the VCR (continued) 4 Press RF CHANNEL. The TV system indicator appears in the display window. RF CHANNEL Press PROGRAM +/– to select the correct TV system. If your TV system is Select PROGRAM B/G G II D/K K Selected TV system SP APC 5 Tune the TV to the same channel as SONY VIDEO CASSETTE shown in the display window so that RECORDER the picture on the right appears on the TV screen. Refer to your TV manual for tuning instructions. If the picture does not appear clearly
Summary of the content on the page No. 9
Getting Started Step 5 Selecting a ?/1 language You can change the on-screen display language from English to Arabic. 123 456 Before you start… • Turn on your TV and set it to the 789 video channel. 0 MENU OK M/m • ]/1 1 Press ?/1 (on/standby) to turn on the VCR. MENU 2 Press MENU, then press M/m to move the LANGUAGE / LANGUAGE / cursor (B) to LANGUAGE and press OK. • ENGLISH PLAY SELECT :[] OK END : [ OK ] LANGUAGE / 3 Press M/m to select the desired language, ENGLISH PLAY then press OK. • OK [
Summary of the content on the page No. 10
Step 6 Presetting channels First, we recommend that you preset the receivable channels in your area using the One Touch Tuning function or AUTO PRESET in the TUNER PRESET menu. Then, if some channels cannot be preset automatically, set them manually. If there are any unwanted channels among the preset ones, you can disable the channels. PROGRAM +/– Presetting all receivable channels using the One Touch Tuning function ONE TOUCH TUNING ONE TOUCH Press and hold ONE TOUCH TUNING on the VCR for more
Summary of the content on the page No. 11
Getting Started Presetting all receivable channels automatically Before you start… • Turn on the VCR and the TV. MENU • Set the TV to the video channel. OK M/m/
Summary of the content on the page No. 12
Step 6: Presetting channels (continued) 4 Press M/m to move the cursor (B) to TUNER PRESET PROG 1 PLAY AUTO PRESET, then press OK. • SYSTEM B / G D / K I NORMAL / CATV • NORM CATV OK AUTO PRESET All receivable channels are preset in CHANNEL SET 1 numerical sequence. When no more AFT • ON OFF FINE TUNING receivable channels can be found, PLEASE WAIT presetting stops and the picture from the lowest numbered channel is displayed on the TV screen. Note • Picture might disappear for a few seconds dur
Summary of the content on the page No. 13
Getting Started Presetting channels manually PROG +/– Before you start… • Turn on the VCR and the TV. MENU • Set the TV to the video channel. OK M/m/
Summary of the content on the page No. 14
Step 6: Presetting channels (continued) PROG Selected programme 4 Press PROG +/– to select the programme position position. TUNER PRESET PROG14 SYSTEM • B / G D / K I NORMAL / CATV • NORM CATV AUTO PRESET CHANNEL SET 21 AFT • ON OFF FINE TUNING SELECT :[] [ SET : ] 5 Press , repeatedly until the channel you TUNER PRESET PROG14 want is displayed. PLAY SYSTEM • B / G D / K I NORMAL / CATV • NORM CATV AUTO PRESET OK Pressing < goes back to the previous CHANNEL SET 35 AFT • ON OFF channels. FINE TU
Summary of the content on the page No. 15
Getting Started Disabling unwanted programme positions After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. 1 In step 5 on page 14, press programme number button “0” twice to display the number “0” beside CHANNEL SET. 2 Press OK. If the picture is not clear Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. If, however, the picture is not clear, you may also use
Summary of the content on the page No. 16
Step 7 Setting the clock You must set the time and date on the VCR to be able to use the timer recording features properly. MENU Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. OK M/m/
Summary of the content on the page No. 17
Getting Started 4 Set the year, hour and minute in sequence, CLOCK SET PLAY using , to select the item to be set, and 252 . 1 . 20 0 1 TUE 15:30 M/m to select the digits. OK SELECT :[] SET : [ ] END : [ OK ] 5 Press OK to start the clock. PLAY OK Tip • To change the digits when setting, press < to return to the item to be changed, and select the digits using M/m. Note • The menu disappears automatically if you do not proceed for more than a few minutes. Getting Started 17 01GB03GET-ED313.p65 1
Summary of the content on the page No. 18
Basic Operations Playing a tape EJECT CLEAR 123 456 789 0 DISPLAY X PAUSE H PLAY M FF H PLAY x STOP M FF m REW m REW A EJECT X PAUSE x STOP COLOR SYSTEM 1 Turn on your TV and set it to the video channel. 2 Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed. 18 Basic Operations 01GB04BAS-ED313.p65 18 10/1/01, 14:25 SLV-ED313ME GB 3-065-583-11 (1)
Summary of the content on the page No. 19
Basic Operations 3 Press H PLAY. PLAY When the tape reaches the end, it will rewind automatically. OK Additional tasks To Press Stop play x STOP Pause play X PAUSE Resume play after pause X PAUSE or H PLAY M FF during stop Fast-forward the tape m REW during stop Rewind the tape Eject the tape Z EJECT To set the colour system If streaks appear during playback, press COLOR SYSTEM on the VCR to conform to the system that the tape was recorded in. (Normally, the colour system is correctly set whenev
Summary of the content on the page No. 20
Playing a tape (continued) To use the time counter At the point on the tape that you want to find later, press CLEAR. The counter in the display window resets to “0:00:00.” Search for the point afterwards by referring to the counter. SP APC To display the counter on the TV screen, press DISPLAY. Press DISPLAY again and the counter will disappear from the TV screen. Notes • When you play back a tape recorded in the PAL or MESECAM colour system, streaks may appear even if the colour system settin
