Summary of the content on the page No. 1
DIGITAL VIDEOCASSETTE RECORDER
DVW-A500/1
DVW-500/1
DVW-A500P/1
DVW-500P/1
CONTROL PANEL
BKDW-515
INSTALLATION AND MAINTENANCE MANUAL
1st Edition (Revised 3)
Summary of the content on the page No. 2
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, F
Summary of the content on the page No. 3
Voor de klanten in Nederland CAUTION Dit apparaat bevat een (CF)n-Li batterij voor memory back-up. Danger of explosion if battery is incorrectly replaced. Raadpleeg uw leverancier over de verwijdering van de Replace only with the same or equivalent type batterij op het moment dat u het apparaat bij einde recommended by the manufacturer. levensduur afdankt. Dispose of used batteries according to the manufacturer's instructions. Gooi de batterij niet weg. maar lever hem in als KCA. Vorsicht! Bij d
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Table of Contents Manual Structure Purpose of this manual .............................................................................................. 3 Contents ..................................................................................................................... 3 Relative manuals ....................................................................................................... 4 1. Installation 1-1. Installation of Control Panel ..........................................
Summary of the content on the page No. 6
4. Maintenance Menu 4-1. ROM Version .............................................................................................. 4-1 4-2. VTR Maintenance Menu ............................................................................. 4-1 4-3. Panel Maintenance Menu ............................................................................ 4-2 4-3-1. Card Interface Test ..................................................................... 4-2 4-3-2. Buzzer Test............................
Summary of the content on the page No. 7
Manual Structure Purpose of this manual This Manual describes the installation instructions for the digital videocassette recorder DVW-A500/1, 500/1, A500P/1, 500P/1 and the Control panel BKDW-515. This manual contains the information necessary when supplying and installing the unit, assuming use by system/service engineers. Contents The sections covered in the manual are summarized below to give you a general under standing of the manual. Section 1 Installation Explains the installation of the
Summary of the content on the page No. 8
Relative manuals Besides this “Installation and Maintenance Manual”, the following manuals are available. • Operation Manual (Supplied with the VTR or the BKDW-515) This manual is necessary for application and operation of the VTR. • Installation Manual (Supplied with the VTR) This manual describes the items are required to install the VTR and its peripherals. If the BKDW-514 control panel is used, refer to this manual. • Maintenance Manual Part 1 (Supplied with the VTR) This manual describes th
Summary of the content on the page No. 9
Section 1 Installation n The BKDW-515 cannot be installed in the BKDW-511 Control Panel Case. for DVW-A500/1, DVW500/1, DVW-A500P/1, DVW-500P/1 1-1. Installation of Control Panel 4. Fix the both arms at 45 degrees. 5. Connect the harness of the control panel to the connec- 1. Fix a dummy panel for shipping use at 90 degrees. tor (CN580) on the system set-up panel. 2. Loosen the two black screws on the dummy panel. 6. Set the notches of the control panel to the claws of the (Loosen the screws unt
Summary of the content on the page No. 10
1-2. SYS1, SYS2 ROM Versions 1-3. Removal of Control Panel / Replacement of Arms 4. While pushing the loosened black screws in the for DVW-A500, DVW500, DVW-A500P, DVW-500P direction of the arrow, remove the lower control panel assembly from the arms. 1-2. SYS1, SYS2 ROM Versions Lower control panel The control panel BKDW-515 is applicable to the ROMs on the SS-52 board with the following version. SYS1: 4.0 and higher ( ) Screw B3x12 SYS2: 4.0 and higher If the ROMs with lower version than above
Summary of the content on the page No. 11
1-4. Installation of Sub Panel Cover and Switch Cover 1-5. Installation of Control Panel 1-4. Installation of Sub Panel Cover and 1-5. Installation of Control Panel Switch Cover 1. Fix the both arms at 45 degrees. 1. Install the sub panel cover supplied with BKDW-515 2. Connect the harness of the control panel to the connec- to sub control panel. tor (CN580) on the system set-up panel. 3. Set the notches of the control panel to the claws of the arms, and push the control panel until making a cli
Summary of the content on the page No. 12
1-6. Installation Space 1-6. Installation Space Notes on Installation on Cart Machine As for how to mount the unit in a rack, refer to the Installa- . When the digital Betacam recorder is to be mounted on tion Manual supplied with the DVW series. the LMS, you can install not the control panel BKDW- 515 but the BKDW-514 to the recorder. . When the digital Betacam recorder is to be mounted on the FLEXICART, you can install both of BKDW-514/ 515 to the recorder. DVW-A500/1 553 500/1 A500P/1 500P/1
Summary of the content on the page No. 13
1-7. Full Reset of Control Panel 1-8. Extension of Control Panel 1-7. Full Reset of Control Panel 1-8. Extension of Control Panel After installing the control panel in DVW-A500 and To extend the BKDW-515, prepare the following BKDW- DVW-500 (DVW-A500P and DVW-500P for PAL), 510 (Control Panel Extension Kit), AC adapter and the perform the full-reset operation of the control panel only connector box. once before it is used. Parts Required m . 10m Extension Cable (BKDW-510) . When the full-reset o
Summary of the content on the page No. 14
1-8. Extension of Control Panel Notes when connecting the two BKDW-515 . Setup Setting Data The Current Setup setting data inside of the BKDW-515 is transferred to the VTR just after the communication between the BKDW-515 and VTR are established. The ALARM LED on the front panel blinks during the data communication is incomplete. When the two BKDW-515 are connected to a single VTR, last setting data out of two is written over the former data as the effective setting data. If the two BKDW-515 wit
Summary of the content on the page No. 15
Section 2 Service Information 2-1. Location and Function of Printed Circuit Boards Board Name Circuit Function CP-266 Panel Control CPU, EL Control, PIO, Memory Card I/F KY-330 Editing Operation/Tape Transport Control Switches, Memory Card Connector SW-749 Function Control Switches PTC-69 JOG/Shuttle Dial Sensor SW-749 KY-330 CP-266 PTC-69 BKDW-515 2-1
Summary of the content on the page No. 16
2-2. Replacing the Battery for Memory Backup 2-2. Replacing the Battery for Memory Backup BT1 inserted into a socket in IC113 (memory for storing 4. Insert the tip of a flatbladed screwdriver between setup data and cue data) on the CP-266 board is a battery IC113 and BT1 to remove BT1. for memory backup. Mark m . Replace a battery for memory backup every seven years. BT1 . Store all the setup data (cue data if necessary) in a memory card before replacing the Battery for memory backup. (For more
Summary of the content on the page No. 17
2-3. EL Panel Replacement 2-3. EL Panel Replacement 5. Disconnect connector CN7 on the CP-266 board and remove the four screws, then remove the EL panel. 1. Turn off the power switch. 2. Disconnect CN580 on the system setup panel and Screws remove the control panel. (PSW3x10) EL panel 3. Remove the four screws, then remove the cover. Screws (PSW3x10) 4. Remove the seven screws and disconnect connector CN1 on the SW-749 board with the frame lifted from the key panel sub-ass’y. Screws(BVTT3x6) Cov
Summary of the content on the page No. 18
2-4. Error Message 2-4. Error Message 2-4-1. Operation when Checksum Error of Current Setup Data Occurs If the power switch is turned on when the current setup data on the control panel was destroyed for some trouble, message “CURRENT setup DATA ERROR” is displayed on the EL panel. The current setup data is automatically reset to the factory-setting value at the same time. 2-4-2. Correction when Checksum Error of VTR Bank Data Occurs If the power switch is turned on when the VTR bank data on the
Summary of the content on the page No. 19
Section 3 Setup Menu This section describes the menu ITEM-F series used during adjustment. For the operation and ITEM-H00 to ITEM-900 series, refer to the Operation Manual. 3-1. ITEM-F Series Display the ITEM-F series according to the procedure below. 1. Press the SETUP key to enter the setup menu. 2. Press the F6 (VTR SETUP) key to enter the VTR SETUP menu. 3. Press the cursor key while pressing the PLAY button. Item selection Press the cursor key while pressing the PLAY button and adjust the c
Summary of the content on the page No. 20
3-1. ITEM-F Series ITEM DATA Description No. ITEM No. DATA F13 TRACKING 0 off Select whether the tracking control operation with search dial is enabled or not CONTROL VIA 1 on during DT head playback. SEARCH DIAL This item is prepared exclusively for DT adjustment and tracking adjustments. After adjustment is completed, return to the factory setting ‘0 (off)’. 0: Tracking control function is disabled during DT head playback. 1: Tracking control function is enabled by rotating the search dial dur
