Summary of the content on the page No. 1
USER'S GUIDE
68Z3, 78E9 SERIES 220-240V
2
Thank You
3
Safety Instructions
4
Product View
5
Assembly
6-8
Operations
9-12
Maintenance and Care
13
Troubleshooting
14
Replacement Parts
15
Warranty
16
Consumer Services
Summary of the content on the page No. 2
Thanks for buying a BISSELL Vacuum We’re glad you purchased a BISSELL CleanView Dual Cyclonic vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL CleanView Dual Cyclonic canister vacuum is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, conside
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, ■ Young children should be supervised to ensure basic precautions should be observed, that they do not play with the appliance. including the following: ■ Remove plug from electrical outlet before cleaning or maintaining the appliance. REAd ALL ■ If the supply cord is damaged, it must be replaced by the manufacturer or its service INSTRUCTIONS agent in order to avoid a hazard. BEFORE USINg YOUR ■ Do not pick up toxic
Summary of the content on the page No. 4
Product view Handle Air Flow Regulator Flex Hose Telescoping Extension Wand Easy Empty™ Dirt Cotainer Multi-Surface Hose Connector Floor Nozzle Brush Switch CAUTION: Do not plug in your vacuum until you are familiar with all instructions and operating procedures. Upholstery Tool Crevice Tool Dusting Brush Wide Pet TurboBrush™ (select models only) 4 www.bissell.com
Summary of the content on the page No. 5
Assembly 1. Connect the hose to the vacuum by inserting the hose connector into the WARNING: suction opening on the bottom front Plastic film can be of the vacuum. Push in until it clicks dangerous. To avoid danger into the locked position. of suffocation, keep away from babies and children. 2. Connect the telescoping extension wand to the handle end of the hose. 3. Connect the floor nozzle foot onto 1. 2. the telescoping extension wand. 4. Attach the tool holder onto the top port
Summary of the content on the page No. 6
Operations Power cord The power cord is located at the rear of the vacuum. Gently pull out the power cord, watching for the yellow line. Stop pulling the power cord once the yellow line is visible. There is also a red line, which indicates the end of the usable Automatic Cord cord. Do not pull the power cord out Rewind Button beyond the red line. Automatic cord rewind Your vacuum is equipped with an automatic cord rewind. When cleaning is finished, press the power button OFF ( ) a
Summary of the content on the page No. 7
Operations Power Power button Button Turn the power ON or OFF by pressing lightly downward on the power button ( ). Variable suction power control The variable suction power control is located on the back of the vacuum. Turn the control toward the larger dots for maximum suction. Turn the control toward the smaller dots to minimize suction for lightly soiled areas or delicate fabrics. Variable Suction Air flow regulator Control Open the air flow regulator by sliding the regulator
Summary of the content on the page No. 8
Operations Special tools Your BISSELL CleanView Dual Cyclonic is not only a powerful carpet and rug vacuum cleaner, Brush Up 1A. it’s also a versatile bare floor and above floor vacuum cleaner when you select one of the special tools. 1. Floor nozzle: Use to vacuum carpets, rugs and bare floors. Swivel head turns to get into tight spaces and fits under cabinets. 1B. A. To vacuum carpets and rugs, push Brush Down the brush switch to the carpet position . This will pull the brus
Summary of the content on the page No. 9
Maintenance and care Emptying the dirt container Empty the dirt container as soon as WARNING: the dirt reaches the “FULL” lines on To reduce the risk of electric the sides of the dirt container. shock, turn power switch OFF and disconnect plug from electrical 1. Unplug the vacuum from the electrical outlet before performing outlet. maintenance or troubleshooting checks. 2. Press the dirt container release button located on the back of the carry handle and lift up to remove. 2. 3.
Summary of the content on the page No. 10
Maintenance and care Cleaning the inner cyclone & screen continued 6. The tank may also be wiped clean with a damp cloth. Make sure the tank is completely dry before reassembling. 7. To reassemble, hold the carry handle and place the screen back onto the top portion of the dirt container. Be sure to align the notch on the top with the insert on the flat edge of the screen. Then place the inner NOTICE: This product is intended for household cyclone back into the screen by aligning
Summary of the content on the page No. 11
Maintenance and care Cleaning the Post-motor HEP A media filter* The post-motor filter is a H13 HEPA media filter*, which assists in the fil- tration process to return clean air to 2. the room. 1. Turn the power OFF. Unplug the vacuum from the electrical outlet. 2. The post-motor filter is located behind the door labeled “FILTER” on the rear of the vacuum. Open the door by pushing down on the tab of the door and pulling out to remove. 3. 3. Remove the post-motor HEPA media Post-Motor H
Summary of the content on the page No. 12
Maintenance and care Maintaining the Wide TurboBrush Pet (Select models only) The Wide TurboBrush Pet should be checked regularly for clogs or debris wrapping around the brush. 1. Unplug the vacuum from electrical outlet. 2. If a clog is present or debris is visible, turn the collar on the neck of the Wide Pet TurboBrush counterclockwise to the unlocked position to remove the faceplate and clear any obstructions. 3. To clean debris from the brush, remove the brush from the drive belt a
Summary of the content on the page No. 13
Troubleshooting WARNING: To reduce the risk of electric shock, turn power OFF and dis- connect plug from electrical outlet before performing maintenance or troubleshooting. Vacuum cleaner won’t run Possible causes Remedies 1. Vacuum cleaner is not plugged in 1. Check electrical plug 2. Power button is not pressed down 2. Press power button down 3. Thermal protector activated 3. Allow vacuum to cool for 1 hour, see page 12 Vacuum cleaner won’t pick up or low suction Possible causes Remedies
Summary of the content on the page No. 14
Replacement parts - Item Part No. Part Name 1 203-1578 Hose 2 203-1579 Telescoping Extension Wand 3 203-1536 Multi-Surface Floor Nozzle 4 203-1583 Tool Holder 5 203-1581 Upholstery Tool 6 203-1580 Crevice Tool 7 203-1582 Dusting Brush 8 203-1290 Wide TurboBrush Pet 9 203-1598 Inner Cyclonic Assembly 10 203-1569 Pre-Motor Filter 11 203-1557 Post-Motor HEPA Media Filter* 1 2 3 4 5 6 7 8 9 10 11 *The Filter Media, not the vacuum as a whole, complies with the High Efficiency Particulat
Summary of the content on the page No. 15
Warranty - BISSELL CleanView™ dual Cyclonic Vacuum This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or contact your local in country distributor. Limited One Year Warranty Subject to the *EXCEPTIONS AND EXCLUSIONS identifie
Summary of the content on the page No. 16
BISSELL consumer services If your BISSELL product should require service: Call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. If you have questions about your warranty or need replacement parts please contact the numbers below. For UK inquiries: For spare parts and accessories: Monday - Thursday 9 am — 5
