Summary of the content on the page No. 1
HA RD FLOOR SC RU BBE R
(ELECTRIC VERSIONS)
Operating Instructions (ENG)
MIEL SMOWN: TC20T
MODEL: VOLTAGE
TCZOE - (20” Non- Traction) 115V
QEsr . . . for Continuous Improvement.
Wipgsor’s Quality Management System is Certified IS0 9QOl.
C€
IPX4
Read these instructions before operating the machine.
TC20E 98447 03/13/00
Summary of the content on the page No. 2
MACHINE DATALOG MODEL . DATE OF PURCHASE . SERIAL NUMBER . SALES REPRESENTATIVE . DISTRIBUTOR NAME . OPERATIONS GUIDE NUMBER . 98447 PUBLISHED . 7/1/96 @Copyright 1996 Windsor Industries. Printed in U.S.A. TABLE OF CONTENTS Cover ...................... 1 Squeegee Assembly .............. 14 Data Log / Table of Contents .... 2 Squeegee Assembly Parts List ...... 15 Safety Precautions ............ 3 Valve Assembly .................. 16 Safety Precautions (cont.) ...... 4 Valve Assem
Summary of the content on the page No. 3
SAFETY IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be fallowed, including the following: READ ALL INSTRUCTIONS BEFORE USING MACHINE TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY: Connect machine to a properly grounded outlet only. See grounding instructions. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. Do not use outdoors on wet surfaces. Do not allow to be used as a toy. Clo
Summary of the content on the page No. 4
SAFETY The following symbols are used throughout this guide as indicated in their descriptions: WHEN TRANSPORTING MACHINE INA TRAILER: HAZARD INTENSITY LEVEL 0 Make sure the ramp angle is no more than There are three levels of hazard intensity identified lo", and the ramp is strong enough to by signal words -WARNING, CAUTION and FOR support the machine. SAFETY. The level of hazard intensity is deter- 0 Make sure ramp is clean and dry. mined by the following definitions: 0 Put ram
Summary of the content on the page No. 5
SAFETY/OPERA TIONS PREPARING FOR OPERA TION(Cont..) EXTENSION CORDS: 4.) Plug the power cords together and twist into locked If an extension cord is used, the wire size must be at least one position. Attatch the power cord to the yellow strain size larger than the power cord on the machine, and the cord relief as shown. Plug power cord into a properly must be a type SJTW/SSTW:A. grounded wall outlet. 5.) Turn vacuum motor switch on and off to make sure HOW IT OPERATES there is electr
Summary of the content on the page No. 6
OPERATION CONTROLS 6 1 Brush Switch. Turns brush on/off. TOP VIEW \ 2 Vacuum Switch. Turns vacuum motor on/off. 3 Main Handle. 4 Brush Motor Circuit Breaker. Protects brush motor from overheating. 5 Vacuum Motor Circuit Breaker. \ 1 Protects vacuum motor from overheating. 2 6 Solution Lever. Controls the amount of BA solution flow to the floor. 7 Squeegee Lift Lever. Raises and lowers squeegee. 8 Scrub Deck Lift Lever. Raises and lowers scrub deck. 9 Recovery Tank Drain Hose.
Summary of the content on the page No. 7
MAINTENANCE Maintenance Item Daily Weekly Monthly Annually * Before Starting Check Vac Hose Connections the Work Period * Clean the Squeegee Blades * Inspect Brush or Pad Inspect Vac Fan Foam Breaker I*I I I I * Inspect power cord for wear * End of Work @ Drain & Rinse Tanks Period Raise Squeegee Assembly I*I I I I Before Storing * Remove the BrushPad * Check the BrushLPad for Damage and or wear * Clean Squeegee Blades & Foam Breaker * Remove lint build-up from screen i
Summary of the content on the page No. 8
MAINTENANCE VACUUM NOTE: Periodically check the length of the car- MOTOR bon brushes. Replace carbon brushes which are 7. Disconnect battery leads and remove batteries less than 3/8" long. from compartment. 2. Remove (6) bolts holding vac motor/ plate assembly to recovery tank. 3. Disconnect vac motor lead from connector II and lift out vac motor/ plate assembly. 4. Check motor brushes. When wom to 3/8" replace both brushes. I PART NO. 14695 U After the machine has been used for
Summary of the content on the page No. 9
MAINTENANCE SQUEEGEE DEFLECTION SQUEEGEE ASSEMBLY INCORRECT Before and during use of machine, use a damp cloth to wipe the outside and inside of squeegee to remove buildup of for- eign material on the squeegee blades. This prevents streaking and residue on the floor. Squeegee wear: After extended use, the squeegee blades will wear. To im- prove squeegee performance and extend wear, proceed as follows: 1. Turn off all switches and place the machine on a level surface. Raise the squee
Summary of the content on the page No. 10
TROUBLE SHOOTING GUIDE Dead electrical circuit Check building circuit breaker or fuse box Power switch failure Replace Faulty power cord Replace Follow grounding instructions exactly. Contact an electrician to check building’s wir- ing. Have a trained service technician check machine’s wiring Replace Replace Replace I 1 Faulty switch Center and seal dome over tank. Replace or repair using acrylic plastic cement only. With power off clean screen. Tighten cuffs turning counterc
Summary of the content on the page No. 11
4 + J WHT 880094 76050 VACUUM SWITCH BRUSH CIRCUIT BREAKER I BLK I BRUSH SWITCH c POWER IN SWITCH REARVIEW
Summary of the content on the page No. 12
TA NKS AND FRAME 22 REAR VIEW TC20E 98447 12-01 -99 I2
Summary of the content on the page No. 13
TANKSAND FRAME PARTS LIST Ref PartNo. CNy Description 1 20046 2 CLAMP 9. 2 25 HVSt 2 87090 11 WASHER, 1/4FlAT 3 27759 1 CUFF, 1.5’ BLK HOSE 4 27188 1 CORD, DRAIN HOSE PLUG 5 27282 1 CUFF, 1.5 SLIP X 1.5 HOSE 6 L1416 1 ww 7 28055 1 DOME, TC MODIF. 8 34303 1 FRAME,MAlN 9 34305 1 FLOAT, RECOVERY SHUT-OFF 10 35060 1 GASKET,DOME 11 39472 1 ,. DKAlN 12 39383 1 HOSEASM,VAC 13 40019 1 HOSEBARB, 1.5 DOUBLE 14 50485 1 LABEL, WINDSOR LOGO 15 50742 1 LABEL, EXPLOSION WARNING 16 8081 9 2 WAS
Summary of the content on the page No. 14
SQUEEGEE ASSEMBLY SQUEEGEE SUB ASSEMBLY l*l A 35 --t v -1 9 58 -7 79 35 -% 74 TCPOE 98447 1 I/l 1/99
Summary of the content on the page No. 15
SQUEEGEE ASSEMBLY PARTS LISTT 57 87080 1 WASHER, .5 X 1.25 FLAT GR8 PLTD 58 87083 11 WASHER, 5/16 SPLIT LOCK PLTD - OPEN 59 871 78 1 WASHER, 5/8lD X 2 X .5 THK 60 61 871 37 2 WASHER, 5/81D X 2.00D X 3/32 THK 62 89059 2 WHEEL, SQUEEGEE BUMPER TC20E 98447 I 1 /I 1/99 15
Summary of the content on the page No. 16
VALVE GROUP 8 (FROM SOLUTION TANK) 10 (SOLUTION DRAIN HOSE) w' - Detail -A- 16 TCPOE 98447 3/26/98
Summary of the content on the page No. 17
VALVE ASSEMBLY PARTS LIST 2 140146 1 Brkt, Solution Valve Mtg. 3 20042 3 Clamp, 3/8 Hose 4 27372 1 CAP,STRAlNER 5 27726 1 Cable, Solution 6 70088 2 Scr, 10-32 x 1/2 PPHMS SS 7 57104 1 Nut, 10-32 w/star washer PLTD 8 39380 1 Hose, 1/2 id nylobraid 6" 9 39381 1 Hose, 1/2 ID Clear x 22" 10 39444 1 Hose, 1/2x5" Clear (All models except X) 11 - - OPEN 12 73383 1 STRAINER, 3/8 NPT 20 MESH 13 - - OPEN 14 40027 2 Hosebarb, 3/8 MPTxl/2 90"nyl 15 OPEN 16 41 184 1 Housing, strainer 17 OPEN
Summary of the content on the page No. 18
SCRUB DECKASSEMBLY 23 I' 18 TCPOE 98447 3/26/98
Summary of the content on the page No. 19
SCRUB DECK ASSEMBLY PARTS LIST serial No.. I Ref PsrtNo. Qty Descriptlon Notes From To 1 20077 1 CLAMP, WUKM #HS356 I I 2 27527 1 CONDUIT, PT17E BRUSH MOTOR - OPEN 34 80604 TCPOE 98447 3/26/98 19
Summary of the content on the page No. 20
MECHANICAL CONTROLS ASSEMBL Y 37 - 44 -> 47 - n-11 44 -9 26 - Q 32 ____ TCPOE 98447 03/13/00 20
