Summary of the content on the page No. 1
SCRUBBER
USER MANUAL
Model: FANG 18C
VIPER CLEANING EQUIPMENT CO., LTD
Address: Liangbian village, Liaobu town, Dongguan city, Guangdong Province, CHINA
Summary of the content on the page No. 2
USER MANUAL ENGLISH TABLE OF CONTENTS INTRODUCTION............................................................................................................................... ...............................2 MANUAL PURPOSE AND CONTENTS .......................................................................................................................................... 2 TARGET..............................................................................................................
Summary of the content on the page No. 3
ENGLISH USER MANUAL INTRODUCTION NOTE The numbers in brackets refer to the components shown in Machine Description chapter. MANUAL PURPOSE AND CONTENTS The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal. Before performing any procedure on the machine, the operators and qualifi
Summary of the content on the page No. 4
USER MANUAL ENGLISH CHANGES AND IMPROVEMENTS Viper constantly improves its products and reserves the right to make changes and improvements at its discretion without being obliged to apply such benefits to the machines that were previously sold. Any change and/or addition of accessories must be approved and performed by Viper. OPERATION CAPABILITIES These scrubber-dryers are used to clean (scrubbing and drying) smooth and solid floors, in civil or industrial environment, under safe o
Summary of the content on the page No. 5
ENGLISH USER MANUAL GENERAL INSTRUCTIONS Specific warnings and cautions to inform about potential damages to people and machine are shown below. DANGER! – Always disconnect the power supply cable when the machine is not in use, before performing maintenance procedures, before replacing the parts before opening any access panel. – This machine must be used by properly trained and authorised personnel only. Children or disabled people cannot use this machine. – Do not wear jewel
Summary of the content on the page No. 6
USER MANUAL ENGLISH – While using this machine, take care not to cause damage to people or objects. – Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects. – Do not put any can containing fluids on the machine. – The machine working temperature must be between 0°C and +40°C. – The machine storage temperature must be between 0°C and +40°C. – The humidity must be between 30% and 95%. – Do not use the machine as a means of transport. – Do no
Summary of the content on the page No. 7
ENGLIS USER MANUAL ENGLISH MACHINE DESCRIPTION MACHINE STRUCTURE 1. Solution Tank 2. Recovery Tank 3. Clear Cover 4. Control Box 5. Switch lever 6. Drain Hose 7. Vacuum Hose 8. Water Hose 9. Squeegee Assembly 10. Transport Wheels 11. Bumper 12. Skirt 13. Brush Motor Switch 14. Vacuum Motor Switch 15. Knob 16. Plate 3 4
Summary of the content on the page No. 8
USER MANUAL ENGLISH ACCESSORIES/OPTIONS In addition to the standard components, the machine can be equipped with the following accessories/options, according to the machine specific use: 1．Brush 2．Pad driver For further information concerning the optional accessories, contact an authorised Retailer. TECHNICAL DATA Model FANG 18C Solution Tank Capacity 30 liter Recovery Tank 41 liter Cleaning Path 45 cm (18") Pad Pressure 30 kg Squeegee Width 75 cm (28") 2 Coverage
Summary of the content on the page No. 9
ENGLISH USER MANUAL WIRING DIAGRAM FOR FANG 18C 8 FANG 18C 80188EU(1)2009-01
Summary of the content on the page No. 10
USER MANUAL ENGLISH USE SCRUBBER SETUP NOTE Read operators manual thoroughly prior to operating or servicing this machine!!! a) PRE-OPERATION CHECKS 1. Sweep the outside of the machine. 2. Make sure the voltage of machine conform to local voltage. (220-240V) 3. Check that squeegee is properly installed. 4. Check that brush / pad is properly installed. 5. Bumper doesn’t touch the floor directly. The gap between the bumper and the floor surface can be adjusted
Summary of the content on the page No. 11
ENGLISH USER MANUAL BASIC OPERATION WARNING! Do not operate machine unless you have read and understand this manual. 1. Adjust control housing to a comfortable operating height by squeezing together the two thumb levers directly underneath the housing. 2. Lower squeegee assembly to the floor. 3. Turn brush motor switch to “on” position. 4. Turn vacuum motor switch to “on” position. 5. Rotate the ball valve of solution tank to horizontal position. Solut
Summary of the content on the page No. 12
USER MANUAL ENGLISH ENGLISH DRAINING TANKS a) DRAINING SOLUTION TANK NOTE Any time scrubbing operation is completed, the solution tank should be drained and cleaned. 1. Pull down on the clear tube (back left of the machine) to remove it from the hose barb. This will allow the solution to flow freely into a bucket or floor drain. 2. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines. 3. Once tank is
Summary of the content on the page No. 13
ENGLISH USER MANUAL MAINTENANCE To keep the machine performing well for many years, please follow the following maintenance procedures. WARNING! Always confirm that the machine is unplugged prior to performing any maintenance or repairs! WARNING! Repairs are to be completed by Authorized Service Centers only. Any repairs completed by unauthorized persons will void the warranty. DAILY MAINTENANCE 1. Remove pad driver / b
Summary of the content on the page No. 14
USER MANUAL ENGLISH Fig. 4 BRUSH/PAD CLEANING CAUTION! It is advisable to wear protective gloves when cleaning the brush/pad because there may be sharp debris. 1. Remove the brush/pad from the machine, as shown in Use chapter. 2. Clean and wash the brush/pad with water and detergent. 3. Check the brush bristles for integrity and wear; if necessary, replace the brush. 4. Check the pad for wear; if necessary, replace the pa
Summary of the content on the page No. 15
ENGLISH USER MANUAL TROUBLESHOOTING PROBLEM CAUSE SOLUTION The wiring not connected Check the wiring or contact Viper correctly or bad wiring Distributor No Power Bad brush motor Contact Viper Distributor Carbon brushes worn out Contact Viper Distributor The wiring not connected Check the wiring or contact Viper Vacuum correctly or bad wiring Distributor motor does Bad vacuum motor Contact Viper Distributor not run Carbon brushes worn out Contact Viper Distributor Bad bal
Summary of the content on the page No. 16
USER MANUAL ENGLISH STORAGE WARNING! If you are storing the machine in an area which can freeze, be sure both tanks and the solution plumbing are empty of all water and dry! 1. Always store the machine indoors. 2. Always store the machine in a dry area. 3. Always take off the pad driver / brush 4. Always store the machine with the squeegee assembly raised off the floor. 5. If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the
