Oreck XL5-105HH user manual

Summary of the content on the page No. 1

75724-01 REV A
B

®
S I M P L Y AMAZING
USER’S GUIDE
XL5-105HH
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories

Summary of the content on the page No. 2

Upper 1 2 3 4 5 Handle Connector Assembly 6 7 8 9 10 PRESS UNTIL SNAP IS HEARD ENFONCEZ JUSQU’À ENTENDRE UN BRUIT PRESIONE HAST A ESCUCHAR UN CHASQUIDO DE SUJECI ÓN 11 12 13 14 15 16 17 18 19 20 OLD NEW 21 22 23 24 25 Retainer Spring Ressort de retenue Resorte retenedor O-ring Anneau torique Anillo tórico Intake Opening Intake Opening Ouverture d’admission Ouverture d’admission Abertura de admisión Abertura de admisión Fan Housing Connector Tube 26 27 28 29 Boîtie

Summary of the content on the page No. 3

BEFORE OPERATING CLEANER, IMPORTANT SAFETY READ ALL INSTRUCTIONS IN INSTRUCTIONS THIS MANUAL CAREFULLY. When using an electrical appliance, basic precautions should always be followed, Table of Contents including the following: Maintenance and Customer Service, Plug Fitting Instructions, READ ALL INSTRUCTIONS BEFORE Accessories, Important Safety Instructions . . . . . . . . . . . . . . . page 2 USING THIS VACUUM CLEANER Warranty, Troubleshooting Guide . . . . . . . . . . .

Summary of the content on the page No. 4

Warranty Troubleshooting Guide ORECK MANUFACTURING COMPANY: (Oreck 21180 Johnson Road; WARNING: Unplug cord from electrical Long Beach, MS, USA 39560 gives you the following warranty for this outlet before servicing. product only if it was originally purchased for residential use, not resale from Oreck or an Oreck Authorized Retail Dealer.) SAVE SERVICE CALLS...CHECK THESE FIRST: Oreck will repair or replace, free of charge, to the original purchaser, any • Is the disposable filte

Summary of the content on the page No. 5

3. If at any time the machine does not pick up properly or makes an Parts List unusual noise, STOP OPERATION and service. 4. Although your upright will pick up pins, paper clips, and other To assist you in identifying components of your vacuum, the parts have small objects, it is recommended that these be removed from the been numbered as follows: floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan an

Summary of the content on the page No. 6

fig. 19 Rotate both bearing assemblies at ends of brush roll to show CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor Surfaces and Polished Floor Finishes "OLD" and replace in the holding channels in the housing. Use floor and floor finish manufacturer’s recommended methods of NOTE: The bearing assembly setting marked "OLD" has no ribs on the cleaning. The metal strip on the base of the cleaner could be damag

Summary of the content on the page No. 7

fig. 29 Many times blockage occurs due to a full dust bag causing dirt to back down the air flow system. When that happens, the blockage will be at the top of the system, starting in the area where the dust bag connects to the connector assembly. NOTE: If the above actions do not correct the problem, contact an Oreck Authorized Service Center or call the customer service center at: 0845 603 0153. 6

Summary of the content on the page No. 8

© 2005 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings, LLC. Printed in America. 75724-01 REV A 04/05 ECN# R-7971