Summary of the content on the page No. 1
Owner’s Manual
Hoover
®
English pp. 1-12
Español pàg.13-19
TM
WindTunnel
Français p.20-26
Bagless Canister Cleaner
with Powered Nozzle
®
Review this manual before
operating cleaner.
www.hoover.com
Summary of the content on the page No. 2
Fill in and retain The model and serial number are located on the bottom of the cleaner. For your personal records, please enter the COMPLETE model and serial number in the spaces provided and retain this information. Your cleaner is model________________________________________________________ and has serial number ______________________________________________________ It is suggested that you attach your sales receipt to this owner’s manual. Verification of date of purchase may be required for
Summary of the content on the page No. 3
1. Assembling cleaner This cleaner was inspected and packaged carefully before being shipped from the factory. If you should happen to need assistance during assembly or operation, Visit us online at www.hoover.com to find the service outlet nearest you (click on the “Service” button) OR Call 1-800-944-9200 for an automated referral of authorized service outlet locations (U.S. only) OR Call 1-330-499-9499 to speak with a representative in the Hoover Consumer Response Center. Carton contents
Summary of the content on the page No. 4
2. How to use Cleaner description 5 13 2-1 14 15 21 4 11 10 7 12 18 6 16 20 3 17 1 9 19 8 2 The assembled cleaner will look like the drawing. 1. WindTunnel™ carpet and floor 13. Power ON/Suction control switch power nozzle: automatically 14. Floor/Carpet selector switch: adjusts to different carpet pile power nozzle agitator control heights 15. OFF switch 2. Headlight 16. Telescoping wand connector end 3. Quick disconnect pedal: step 17. Cord rewind pedal: step on pedal on pedal to separate
Summary of the content on the page No. 5
A Polarized plug 2-2 2-3 To reduce the risk of electric shock, this C appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the D outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change B the plug in any way. Telescoping extension Turning cleaner on wand and adjusting power The spring latch (D) on the wand allows level
Summary of the content on the page No. 6
2-7 2-8 2-9 G F J I H Edge cleaning Select the proper tool Cleaning tools F. Dusting brush/furniture nozzle this Special edge groomers are provided on The cleaning tools are conveniently 2-in-1 tool may be used with the brushes both sides of the nozzle to remove dirt in stored in the cleaner underneath the tool in place (dusting brush) for carved furni- carpet near baseboards and furniture. lid. Pull up on edge of lid in recessed ture, table tops, books, lamps, lighting Guide side of nozzle pa
Summary of the content on the page No. 7
3-3 3-4 3-5 E C D C Grasp the filter and rotate counter-clock- Cleaning the filter Washing the dirt cup wise. Clean the filter using the small The dirt cup filter (D) is located under Turn cleaner off and disconnect from brush located under the tool lid. the dirt cup lid. electrical outlet. If desired, the filter may be rinsed by When the filter needs to be cleaned, the Remove the dirt cup by pressing the running it under cold tap water. Do not red Suction Control Switch light (E) will button
Summary of the content on the page No. 8
3-8 3-9 3-10 G G Return nozzle to original position and lift Remove brush roll cover (G) by remov- Lift off brush roll cover (G). off hood. ing the 3 Phillips head screws. 3-11 3-12 3-13 I J H Lift up end of agitator brush roll. Remove If belt is not broken but is stretched or Stretch belt back and attach to motor cut, pull it off the motor pulley (H). old belt from agitator pulley (I) and pulley. replace with new belt. Lettering on belt Hold opposite end of agitator brush roll in must be vi
Summary of the content on the page No. 9
What to buy Headlight replace- 3-16 When purchasing a new agitator brush roll, ment ask for HOOVER part no. 48414-071. The headlight, located on top of the How to replace power nozzle, operates when the clean- Disconnect cleaner from electrical er is turned on. Use only HOOVER outlet. part no. 27317-307, which is a fused bulb, when replacing the headlight. 1. Remove hood, duct cover, belt and brush roll as shown in Figs. 3-8 to How to replace 3-13. Disconnect cleaner from electrical outlet a
Summary of the content on the page No. 10
3-20 3-21 3-22 D B C C E 2. Unscrew the two Philips screws and 3. Remove agitator including end plates 6. With curved ends down, slide end remove belt guard (B). (C) and discard. plates (C) of brush roll into slots (E) on tool. 4. Inspect belt to ensure that it is in good condition. If belt is cracked, gouged or broken, replace it (see follow- ing section). 5. Insert brush roll through belt and position belt over gear teeth (D) on brush roll. Powered hand tool 3-23 3-24 Belt replacement B Inspec
Summary of the content on the page No. 11
Lubrication Problem: Powered hand tool 4. If you have a (available at additional cost if not The motor is equipped with two bear- included with your cleaner) brush problem ings that contain sufficient lubrication for roll won’t turn the life of the motor. The addition of If a minor problem occurs, it usually can lubricant could cause damage. Possible cause be solved quite easily when the cause is Therefore, do not add lubricant to Possible solution found by using the check list below. either
Summary of the content on the page No. 12
Full One Year A 4-2 Warranty (Domestic Use) Your HOOVER® appliance is warranted in normal household use, in accordance with the Owner’s Manual against original defects in material and workmanship for a period of one full year from date of purchase. This warranty provides, at no cost to you, all labor and parts to place 4. Make sure power nozzle plug is dis- this appliance in correct operating con- connected from hand grip. Then check dition during the warranted period. This for blockage in nozzl
