Summary of the content on the page No. 1
Momentum Cyclonic
BAGLESS V ACUUM
USER’S GUIDE
3910 SERIES 220-240V
3
Safety Instructions
4
Product View
5-6
Assembly
6-9
Operation
10-16
Maintenance and Care
17
Troubleshooting
18
Consumer Services
19
Replacement Parts
20
Warranty
ug603-2377_3910E_207.indd 1 ug603-2377_3910E_207.indd 1 2/7/07 4:03:31 PM 2/7/07 4:03:31 PM
Summary of the content on the page No. 2
Thanks for buying a BISSELL vacuum We’re glad you purchased a BISSELL vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL vacuum is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance. My great-grandfather invented the floor sw
Summary of the content on the page No. 3
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, ■ Remove plug from electrical outlet before cleaning or basic precautions should be observed, maintaining the appliance. including the following: ■ If the supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to READ ALL INSTRUCTIONS avoid a hazard. ■ Do not pick up toxic material (chlorine bleach, BEFORE USING YOUR ammonia, drain cleaner, petrol, etc.). UPRIGHT VACUUM. ■ Do not
Summary of the content on the page No. 4
Product view Handle ™ Quick Release Cord Wrap Hose and Cord Clip Dusting Brush/ Upholstery Tool Power Cord Carry Handle Stretch Hose Twist ‘n Crevice Tool ™ Snap Extension Wand Hose ™ TurboBrush Power Switch Clean Filter Indicator Curved (Select Models Only) Hose Wand Upper Tank Lower Hose Clip HEPA Media ™ Easy Empty Post Motor Filter Dirt Container Hose ™ Washable Lock ‘n Seal Lever Wand Pre-Motor Filter Base Handle Release Pedal Headlight Height Adjustment Foot Knob Window Scuff
Summary of the content on the page No. 5
C AUTION: Assembling your vacuum Do not plug in your vacuum cleaner until The only tool you’ll need to assemble your you are familiar with vacuum cleaner is a Phillips screwdriver. all instructions and Attach handle to vacuum operating procedures. 1. Locate the handle and cord wrap. Remove the screw packet taped to the cord wrap. 2. 2. Stand the vacuum upright and from the rear of the unit, slide the base of the handle firmly into the grooves at the top of the vacuum body. 3. IMPORTA
Summary of the content on the page No. 6
1. Twist 'n Assembling your vacuum Snap Hose Attach vacuum hose and tools 1. Line up the tabs on the base of the Twist ‘n Snap hose with the corresponding notches 6. on the hose collar as shown. 2. Turn the Twist ‘n Snap hose to the left to lock the hose into place. 3. Connect the curved hose wand to the hose. Grasping the curved hose wand, slide the end of the curved hose wand onto the hose wand base. Snap the hose into the hose clip. NOTE: The vacuum will not operate effectively C AU
Summary of the content on the page No. 7
1. Operation 2. Handle positions Press the handle release pedal, located on the lower left side of the vacuum, with your foot to place your vacuum into one of three cleaning 3. positions. 1. Upright – For storage and above floor cleaning with tools. 2. Normal Cleaning – Press handle release Tip: pedal once. Position used for most Before cleaning under low furniture, check household floor cleaning tasks. area first for objects that might harm the unit 3. Low Cleaning – With the vacuum in
Summary of the content on the page No. 8
Operation Clean filter indicator Select Models Only The clean filter indicator tells you when the airflow in your vacuum is reduced due to dirty filters or a clog in the hose. The clean filter indicator will remain Clean green while the unit is running until the airflow is Filter reduced by a clog or dirty filter. At that time, it begins Indicator to change to red or black. When it is fully red, the airflow is significantly reduced or clogged by a dirty filter. Follow the steps on page
Summary of the content on the page No. 9
Operation Crevice Tool: Use in tight narrow spaces. Extension Wand: Use with desired attachment for a longer reach. Curved Hose Wand: Use with desired attachment for a longer reach or for cleaning hard to reach places. ™ TurboBrush : Use rotating brush action for small areas such as stairs and upholstery. Tip: Hair, string and small objects can block NOTE: Press gently when using the TurboBrush to maximize cleaning. the vacuum hose or tools. Check them Too much pressure will cause the b
Summary of the content on the page No. 10
Maintenance and care To maximize your cleaning performance and extend the life of your vacuum, it is very important that you empty your dirt container W ARNING: and check and clean your filters frequently. To reduce the risk of electric Perform the following maintenance steps: shock, turn power switch OFF 1. Empty the dirt container when the dirt reaches and disconnect plug from the “Full” line on the container, or more frequently electrical outlet before to prevent overfills. For bes
Summary of the content on the page No. 11
Maintenance and care Cleaning the pre-motor and post-motor HEPA media filter 1. Unplug the vacuum from electrical outlet. 2. The pre-motor filter protects the motor from dirt particles. It is located in the slide out tray underneath the dirt container. If the filter becomes dirty, pull out the tray, lift out the foam filter pad and clean it. NOTE: The pre-motor filter may be hand washed in cold water with mild detergent. Rinse well and air dry thoroughly before replacing. Post-Motor 3
Summary of the content on the page No. 12
Maintenance and care Check rotating floor brush and drive belt You should check your vacuum cleaners rotating floor brush and drive belt regularly WARNING: for wear or damage. You should also clean To reduce the risk of injury the brush and brush ends of strings, hair from moving parts, turn and carpet fibers. This type of debris can power switch off and wrap around the brush and hamper its disconnect plug from ability to effectively clean your carpet. Also electrical outlet. remove
Summary of the content on the page No. 13
Maintenance and care Replace drive belt 1. Unplug the vacuum from electrical outlet. 2. With rotating floor brush removed from vacuum cleaner (Steps 1-4 of check rotating floor brush and drive belt), grasp old drive belt and remove from motor pulley. Discard the old drive belt. 3. Place new drive belt over motor pulley 3. and loop other end over rotating floor Motor Pulley brush in the space between the bristles. NOTE: It is important that you use only genuine BISSELL replacement belts.
Summary of the content on the page No. 14
Maintenance and care Maintaining TurboBrush The TurboBrush should be checked regularly for clogs or debris wrapping around the brush. 2. 1. Unplug the vacuum from electrical outlet. 2. If a clog is present or debris is visible, unscrew the two screws on the back of the TurboBrush to remove the faceplate and clear any obstructions. 4. 3. To clean debris from the brush, remove the brush from the drive belt and clean debris. 4. Reposition the drive belt on the brush. Place ends of brush in sl
Summary of the content on the page No. 15
Maintenance and care Clearing clogs 2. Low suction or poor pickup may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor, check for clogs. 1. Unplug the vacuum from electrical outlet. 3. 2. Empty dirt container. 5. 3. Check upper tank for build up or clogs. 4. If you notice a clog in the upper tank, remove the separator plate (see section "Cleaning the Upper Tank" on page 16). 5. Grasp the curved wand and separate it from the hose wand base. Check fo
Summary of the content on the page No. 16
Maintenance and care Cleaning the upper tank 1. Unplug the vacuum from electrical outlet. 2. Remove the dirt container as instructed in "Empty Dirt Container" on page 10. 3. 3. Using a short Phillips screwdriver, take off the separator plate by removing the two screws that secure it to the upper tank. 4. Wipe out the inside of the upper tank and the separator plate with a damp cloth moistened with water or a mild cleaning solution. 5. Replace the separator plate and screws. 6. Replace the
Summary of the content on the page No. 17
Troubleshooting W ARNING: To reduce the risk of electric shock, turn power switch OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting. Vacuum cleaner won’t run Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug Vacuum cleaner and tools won’t pick up dirt Possible causes Remedies 1. Incorrect height adjustment 1. Adjust powerfoot to correct height 2. Hose not attached to suction opening 2. Firmly push curved hose wand in
Summary of the content on the page No. 18
BISSELL Consumer Services If your BISSELL product should require service: In the UK, Australia, or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. If you have questions about your warranty or need replacement parts please contact the numbers below. For UK inquiries: For Australian inquirie
Summary of the content on the page No. 19
Replacement parts Item Part No. Part Name 1 32074 Style 7/9/10/12/14 Drive Belt (2-Pack) 2 203-1297 Headlight Bulb 3 203-1063 Crevice Tool 4 203-1228 Dusting Brush/Upholstery Tool 5 203-2302 TurboBrush, clear top with black brush roll 6 203-1022 Extension Wand 7 203-2303 Curved Hose Wand 8 203-2304 Twist 'n Snap Vacuum Hose (clear) 9 203-2305 Wide Window Foot Brush Roll (gray) 10 3290 Style 7/8/14 Pre-Motor Foam Filter 11 3091 Style 8/14 HEPA Media Post-Motor Filter 12 203-2306 Hose & Cord Wra
Summary of the content on the page No. 20
Warranty - BISSELL Momentum Cyclonic Bagless Vacuum This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or contact your local in country distributor. Limited One Year Warranty Subject to the *EXCEPTIONS AND EXCLUSIONS identifie
