Summary of the content on the page No. 1
SRC-3810/3815
Touch Screen Remote Control
User Manual
031021
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Preface About this manual This manual is designed to make using the SRC-3810/3815 Touch Screen Remote Control as easy as possible. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. Copyright © Copyright 2003 This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may
Summary of the content on the page No. 4
SRC-38 SERIES User’s Manual Table of Contents Chapter 1 - Introducing the SRC-3810/3815.................................. 1 SRC-3810/3815 Features ............................................................. 1 Unpacking the SRC-3810/3815 .................................................. 2 Identifying Components............................................................. 3 Chapter 2 - Getting Started............................................................. 5 Installing IR-extender .
Summary of the content on the page No. 5
Preface Using Macros .............................................................................. 27 Creating a New Macro .................................................... 28 Deleting a Macro .............................................................. 30 Viewing a Macro ............................................................... 31 Setting QUICK CHs..................................................................... 32 Setting a QUICK CH....................................
Summary of the content on the page No. 6
Summary of the content on the page No. 7
Chapter 1 - Introducing the SRC-3810/3815 Congratulations on your purchase of the SRC- 3810/3815 Touch-Screen Remote Control. The SRC- 3810/3815 is a digital universal remote control that is easy to use, enabling you to control all of your electronic devices equipped with an infrared (IR) remote or RF (SRC-3815) remote model with transmission IR-extender SEL-6000. The SRC-3810/3815 uses a Touch Screen panel and control buttons and is simple to use. Simply select a device and the approp
Summary of the content on the page No. 8
SRC-38 SERIES User’s Manual • SRC-3815 can Choose of IR (direct to device) or RF ( to IR-extender to device) signal transmission. • Lost remote finder button – activates beep to locate when lost (SRC-3815 with SEL-6000 IR-extender). • Large Touch Screen display • Macro sequence function—each macro can store 60 commands • Controls up to 16 devices including DVDs, TVs, Satellite Receivers, VCRs and CDs • Learns the IR codes from your existing remote controls to quickly set up devices.
Summary of the content on the page No. 9
Identifying Components Identifying Components Refer to the following illustration to identify the components of the SRC-3810/3815. Infrared Eye: point the infrared eye at the device you want to operate. Infrared Eye Light Sensor: detects ambient light to automatically set the Light Sensor LCD panel backlight. Quick Channel QUICK CH: enables you to group channel types for easy access. LCD: backlit LCD emulates the LCD hard key controls, and provides a user
Summary of the content on the page No. 10
SRC-38 SERIES User’s Manual For SRC-3815 Remote Control
IR Out jack – Connect the IR blaster cable to this jack to operate a specific device. IR-extender address setting – Set the RF address of the IR- extender by selecting and address number between 0 ~ 9. AC adapter – Plug AC adapter into jack and then into AC outlet. Remote Locator Button – Press locator button to call remote control to make beep signal and locate the remote. (Only for SRC-3815) Infrared Emitter –
Summary of the content on the page No. 11
Chapter 2 - Getting Started This chapter provides you with the information to quickly get using the SRC-3810/3815. Installing IR-extender 1. Plug in AC adapter into AC adapter jack on IR-extender and into AC wall outlet. 2. Set address code. 3. Position IR-extender so that it is aimed at equipment. Use IR blaster cable for equipment out of directional range. Installing Batteries The SRC-3810/3815 operates on four AAA Alkaline batteries (not included). Batteries must be inserted b
Summary of the content on the page No. 12
SRC-38 SERIES User’s Manual Battery Battery half Battery full full low Figure 2: The Battery Icon When the batteries are almost depleted, the battery low icon appears. When the battery low icon appears, you are not allowed to enter setup mode. Battery Tips and Precautions • Immediately replace the batteries when the battery low icon appears. • The SRC-3810/3815 will not lose programmed data when batteries are replaced, but will reset the time. • Always use fresh batteries.
Summary of the content on the page No. 13
About the Touch Screen About the Touch Screen The Touch Screen reduces the number of buttons by changing its configuration for each device selected. In this way, the Touch Screen provides 672 buttons (16 devices x 2 pages x 21 buttons per page). Turning the Touch Screen On Touch the screen to activate it. It will turn itself off after the user-defined power down time period. (To change the time, see Setting the Power Down Time on page 38. Touch Screen Precautions Please read the f
Summary of the content on the page No. 14
SRC-38 SERIES User’s Manual Touch Screen Buttons The Touch Screen buttons enable you to operate the SRC-3810/3815 and your external devices. Use these buttons to program codes from your existing remotes, control your devices, and set up command sequences called macros. You will hear a beep when you press a button. To activate or deactivate the beep, see Setting the Beep Signal on page 39. The SRC-3810/3815 turns itself off after a user specified time. To change the time, see Setting th
Summary of the content on the page No. 15
Entering the Setup Menus Figure 3: Entering the Setup Menus When the battery low icon appears or you are in QUICK CH mode, you are not allowed to enter setup mode. Navigating the Setup Menus While in the setup menus, press and on the Touch Screen to scroll up and down through the menus and settings. Press and to scroll left and right through menus and settings. Press or to confirm settings, and press to exit a menu. Figure 4: Navigating Menus When using the setup menus
Summary of the content on the page No. 16
SRC-38 SERIES User’s Manual The fallowing illustration shows the setup menu tree: Figure 5: Setup Menu Hierarchy The following chapter describes each menu. 10
Summary of the content on the page No. 17
Chapter 3 - Setting Up the SRC-3810/3815 Before the SRC-3810/3815 can be used to control a device, it needs to be configured to display your existing remote control buttons and it must be programmed to send the correct infrared signals. This chapter guides you through the Touch Screen layout and SRC-3810/3815 setup procedure. Before continuing, refer to Navigating the Setup Menus on page 9 to learn how to navigate the menus. Device Menu Enter the setup menus, scroll to Device and p
Summary of the content on the page No. 18
SRC-38 SERIES User’s Manual Creating a New Device Follow these steps to create a new device: 1. Press or to select NEW. 2. Press . 3. Press the device key you want to use for this device (for example AMP). 4. Edit the device label. The label can be up to 8 alphanumeric characters: • Press or to scroll through the characters (from A-Z, 0-9, and the space key). Note: Press and hold or to quickly scroll through the characters. • Press or to move to the previous or next
Summary of the content on the page No. 19
Device Menu You are prompted to select an attribute for the new device. 5. Press or to select a device whose attributes will be loaded to the new device. 6. Press to confirm the entry. Re-Labeling Devices Follow these instructions to edit a device label. 1. Press or to select Relabel. 2. Press . 3. Press the device key you want to relabel (for example TV). 13
Summary of the content on the page No. 20
SRC-38 SERIES User’s Manual 4. Edit the device label: • Press or to scroll through the characters (from A-Z, 0-9, and the space key). Note: Press and hold or to quickly scroll through the characters. • Press or to move to the previous or next character. When selected, the character blinks. • Press to confirm the entry. 5. Press to exit to the device menu. ADDR Setting RF Address ( SRC-3815) Each device button (TV, VCR, DVD etc.) can be set to operate on either
