Summary of the content on the page No. 1
User Guide
TouchLink™
TLP 700MV and TLP 700TV
TouchLink Touchpanel Control Systems
68-1378-01 Rev. B
10 10
Summary of the content on the page No. 2
Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source indicated on the product. This This symbol is intended to alert the user of important operating and maintenance equipment is intended to be used with a main power system with a grounded (neutral) conductor. The (servicing) instructions in the literature provided with the equipment. third (grounding) pin is a safety feature, do not attempt to bypass or disable it. Th
Summary of the content on the page No. 3
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Contents Introduction ............................................1 Accessories and Part Numbers ..............37 About the TLP 700MV and TLP 700TV ............. 1 Included Parts ............................................ 37 Features ........................................................... 2 Optional Parts ............................................ 37 Requirements ................................................... 3 Software ...................................................... 3 Mounti
Summary of the content on the page No. 6
TLP 700MV and TLP 700TV • Contents vi
Summary of the content on the page No. 7
Introduction This guide describes the function, installation and operation of the TouchLink TLP 700MV and TLP 700TV panels. The guide also provides information about optional accessories that are available from Extron for both panels. Unless otherwise stated, the terms “TLP 700 series” and “TLP 700” refer to both models. About the TLP 700MV and TLP 700TV The Extron TLP 700MV is a wall mounted TouchLink panel. The screen displays graphic objects and text, which are associated with user-defined
Summary of the content on the page No. 8
TCP/IP Network Extron Contact Closure IPL 250 IP Link-Ethernet Motion Extron Detector Control Interface IN1508 Scaling Presentation Extron Switcher RS-232 TLP 700MV 7" TouchLink RS-232 Panel Extron Lighting XPA 1002 Extron System IR Control Power Amplier to DVD SI 28 Surface-mount Speakers RS-232 Extron IR Emitter DVD Relay Player Laptop Projector IR Control Screen Control from IPL 250 PC DVI Output Figure 1. TLP 700MV Application Diagram Features 7-inch LCD screen — displays a range of
Summary of the content on the page No. 9
Multiple mounting options — The TLP 700MV can be wall-mounted, rack-mounted, or furniture-mounted. The TLP 700TV comes with a stand that allows it to be placed on a desktop. If the stand is removed, the unit can be VESA-mounted on a wall or furniture using either of the optional Extron kits. See the list of optional parts on page 37 for the part numbers. Color Options for TLP 700MV — The TLP 700MV is available in different color versions. Customization kits — A range of kits are available to
Summary of the content on the page No. 10
Panel Features This section describes: TLP 700MV Front Panel Features and Operations TLP 700MV Rear Panel Features and Connections TLP 700TV Front Panel Features and Operations TLP 700TV Rear Panel Features and Connections TLP 700MV Front Panel Features and Operations 4 DISPLAY LIGHTS 1 MUTE ON AUDIO LIGHTS MUTE OFF SCREEN SPEECH MUTE 5 AUTO SCREEN IMAGE HELP FREEZE ? 6 2 3 Figure 2. TLP 700MV Front Panel a Buttons — These ten backlit push-buttons (five on either side of the screen) can be conf
Summary of the content on the page No. 11
There are three buttons recessed behind the bezel. These buttons are used to configure the unit and reset parameters to factory defaults: DISPLAY LIGHTS MUTE ON AUDIO LIGHTS MUTE OFF SCREEN SPEECH MUTE AUTO SCREEN IMAGE HELP FREEZE ? 7 8 9 10 Figure 3. TLP 700MV Front Panel with Bezel removed g Reboot button — shuts down and restarts the unit without changing any of the parameters. h Reset button — allows the unit to be reset in any of four different modes. For further information see “Reset
Summary of the content on the page No. 12
TLP 700MV Rear Panel Features and Connections 11 12 13 Figure 4. TLP 700MV Rear Panel Features k Power Connector — Connect the two pole, 3.5 mm captive screw connector from the provided power supply to the power supply socket on the rear panel. Ensure the connections have the correct polarity as shown below: POWER POWER 12V Power Receptacle 12V 0.4A MAX Smooth Ridges 0.4A MAX SECTION A–A Power Supply 3/16" Output Cord (5 mm) Max. DC Power Cord Captive Screw Connector Ground +12 VDC Extern
Summary of the content on the page No. 13
NOTES: The length of the exposed wires in the stripping process is critical. The ideal length is 3/16 inches (5 mm). Any longer and the exposed wires may touch, causing a short circuit between them. Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws. Do not tin the wires. Tinned wire does not hold its shape and can become loose over time. l Video Input — Connect an S-video or composite video source to the unit, using these two BNC connectors
Summary of the content on the page No. 14
TLP 700TV Front Panel Features and Operations 4 1 5 6 7 2 8 9 3 Figure 6. TLP 700TV Front Panel Features a Buttons — These ten backlit push-buttons (five on either side of the screen) can be configured to execute user-defined functions using the Extron Global Configurator software (page 25). For information about creating button labels, see page 47. b Motion Sensor — is capped with a small Fresnel lens that focuses light onto the sensor. When no motion has been detected for a user-defined per
Summary of the content on the page No. 15
TLP 700TV Rear Panel Features and Connections With Stand Attached 10 13 11 12 Figure 7. TLP 700TV Rear Features The following connections are available through the back panel when the stand is in place: j LED lights —The Link LED lights green to indicate a good network connection. The Activity LED blinks yellow when network activity occurs. k RJ 45 connector to LAN — Use straight-through twisted pair cable to connect the TLP 700TV to a network switch or router. Use a crossover cable to connect
Summary of the content on the page No. 16
C Gain C Gain Vid / Y Gain Vid/Y Sharp 33-1814-01 A Gain Sharp 33-1814-01 A TLP 700TV Base Features 19 17 18 Figure 8. TLP 700TV Base Features The TLP 700TV stand, which can be removed for VESA mounting, has: q Three adjustable potentiometers — These are used to control sharpness and gain for both S-video luminance (Y) and S-video chrominance (C). If a composite video signal is being used, the gain is controlled by the center potentiometer (Vid/Y). Figure 9. TLP 700TV Potentiometers r Access
Summary of the content on the page No. 17
Initial Calibration This section describes: z z How to Access the Internal On-screen Menus z z The Main, Volume, Time, Network, and Video Screens z z The Screen Touch Calibration Screen How to Access the Internal On-screen Menus When power is first applied to the TouchLink Panel, the unit boots up and displays the opening screen. To access the on-screen menus, press the Menu button, which is located below the screen (see page 5 for the TLP 700MV or page 8 for the TLP 700TV). The menus open at
Summary of the content on the page No. 18
When Auto Backlight is set to Off, the Backlight option allows the backlighting to be set manually from 0 to 100%. Press the Down or Up buttons to highlight the Backlight options and use the volume control knob or press the Down or Up buttons to adjust the backlighting. The current value is shown above the buttons. NOTE: When Auto Backlight is set to On, changing the percentage of Backlight does not affect the amount of backlighting. LED Backlight lights the ten buttons next to the screen. W
Summary of the content on the page No. 19
Time Screen Click on the Down or Up buttons to highlight one of the adjustable time settings. Use the Down and Up buttons or the volume control knob to adjust the Month, Day, Year, Hours, and Minutes. NOTE: The Hours value uses the 24 hour clock. For 10 am, set Hours to 10; for 10 pm, set Hours to 22. Network Screen Set the IP Address or Subnet Mask by pressing the appropriate button. An on-screen keypad appears that allows the user to enter digits from 0 through 9 or “.” (dot). In the even
Summary of the content on the page No. 20
Video Screen The small gray rectangle provides a video preview window that allows the user to adjust the video properties. Click on the Down or Up buttons to highlight one of the adjustable video settings. Use the Down and Up buttons or the volume control knob to adjust: z z Contrast between 0 and 127 (default, 64) z z Color between 0 and 127 (default, 64) z z Brightness between 0 and 255 (default, 128) z z Tint between 0 and 255 (default, 128) Touch Calibration Screen After setting the values
