Summary of the content on the page No. 1
Owner’s Manual
MEDIAMASTER
9802 S
Summary of the content on the page No. 2
Hereby, Nokia declares that this digital receiver, Nokia Mediamaster 9802 S, is in conformity with es- sential requirements and other relevant provisions of Directive 1999/5/EC. This Terminal Equipment is intended for connection to the analogue Public Switched Telephone Networks (PSTNs), in which net- work addressing, if provided, is by means of Dual Tone Multiple Frequency (DTMF) signalling.
Summary of the content on the page No. 3
MEDIAMASTER 9802 S Contents General information 4 Guide 25 List of TV and radio channels 26 For your safety 4 Options (green button) 26 Remote control 5 TV release (0) 27 Front and rear panel 6 Video recording 27 Viaccess smartcard 7 The TEXT button (Teletext) 27 CA module with its smartcard 7 EXIT TV 27 Preparing the remote control 8 Main menu 28 Connecting the Mediamaster to the dish 8 General information 28 Connecting the Mediamaster 9 TV and radio channels 28 Connecting to the TV 9 Edit cha
Summary of the content on the page No. 4
GENERAL INFORMATION ABOUT THE MEDIAMASTER Throughout this manual you will notice that the everyday operation of your Mediamaster is based on a series of user friendly on-screen displays and menus. These menus will help you get the most from your Mediamaster, guiding you through installation, channel selec- tion, viewing and many other functions. All functions can be carried out using the buttons on the remote control, and some of the functions can also be carried out using the buttons on the fro
Summary of the content on the page No. 5
REMOTE CONTROL This section describes how to operate the Mediamaster using the buttons on the remote control. Some of the functions can also be carried out using the buttons on the front panel. Switch the Mediamaster in and out of standby mode. EXIT TV Return to the viewing mode from a menu without storing any settings (in menu mode). Switch between TV or Radio mode (in viewing mode). Turn the sound off/on (mute). - + Adjust the volume of digital programmes. The Mediamaster’s maximum level is
Summary of the content on the page No. 6
FRONT AND REAR PANEL Front panel Button Display Push the button to shows channel number, error messages, release an inserted remote control commands and time in CA module standby mode Slot Slot to put the Mediamaster to move up/down in for a Viaccess for a CA module in and out of standby the menus and to Smartcard with a Smartcard mode change channels. Rear panel AUX SCART DIGITAL AUDIO TELEPHONE TV/VCR ANTENNA * for connection to a VCR, phono connector for connection for an RF-cable to the S
Summary of the content on the page No. 7
ABOUT THE SMARTCARD AND CA MODULE To be able to receive scrambled digital satellite channels you will need a Smartcard and/or a Common Interface CA (Conditional Access) module* from a Service Provider of your choice. There are a few different CA modules on the European market. Each one of the CA modules support a certain kind of encryption system. The Mediamaster supports CA modules which are made to work according to the DVB standard. Depending on which country you use the Mediamaster in, your
Summary of the content on the page No. 8
INSTALLATION OF THE MEDIAMASTER The box for your Mediamaster should contain the following items: • the Mediamaster • remote control with 2 AAA batteries • SCART cable (fully connected 1,0 metre) • aerial/RF cable (double screened 1,5 metres) SCART cable RF cable • owner’s manual and software license agreement • mains cable Remote Owner’s manual mains control License agreement cable About the SCART sockets The rear panel of the Mediamaster is equipped with 2 SCART sockets (see diagram). When you
Summary of the content on the page No. 9
INSTALLATION OF THE MEDIAMASTER General There are many different types of TV/VCR and other equipment that you can connect to the Mediamaster. In this manual you will see some of the most common ways to connect your equipment. If you use RF cables you will have to tune your TV and VCR to the Mediamaster output channel (see page 11). If you have problems with your connections and need help, con- tact your dealer or Service Provider. Connecting to the TV • Connect the SCART cable between the main S
Summary of the content on the page No. 10
INSTALLATION OF THE MEDIAMASTER Connecting a satellite receiver and a VCR • Connect a SCART cable between the main SCART socket on With Nokia smart the TV and the TV SCART socket on the Mediamaster. switch • Connect a SCART cable between the VCR and the AUX SCART VCR socket on the Mediamaster. • Connect an RF cable from the RF output on the VCR to the TV aerial input on the TV. RF • Connect an RF cable from the RF output on the satellite re- ceiver to the RF input socket on the VCR. • Connect th
Summary of the content on the page No. 11
INSTALLATION OF THE MEDIAMASTER Switching on for the first time with SCART connections • Plug in your Mediamaster • Now you will see the ”Welcome” menu on the screen. • Press OK on the Mediamaster remote control to start the In- stallation procedure. You may now proceed to “First time installation”, see next page. Tuning procedure when RF connections are used This procedure is necessary if your Mediamaster is con- nected to the TV with an RF cable, and not via SCART. To tune your TV to the RF si
Summary of the content on the page No. 12
FIRST TIME INSTALLATION General information Once you have correctly connected the Mediamaster, you also have to perform a “First Time Installation.” During this procedure, helpful information is displayed at the bot- tom of the menus. Please note! The OK button always confirms a selection within these menus, and pressing it will take you to the next step in the installation process. However, and this is important, often more than one value has to be entered in a menu. First, perform all necessar
Summary of the content on the page No. 13
FIRST TIME INSTALLATION RF modulator type If the Mediamaster is connected to the TV with a RF cable, you must select the right RF modulator alternative, which is depend- ent on the country where the Mediamaster is being used. Select “Normal (PAL B/G)” for all countries except the UK. Select “UK (PAL I)” when the box is used in the UK. If you get picture but no sound, the RF modulator selection might be wrong. Antenna/satellite selection Select one of the alternatives from line 1 to 4 if you have
Summary of the content on the page No. 14
FIRST TIME INSTALLATION Line through on the antenna satel- 1 4 lite selection menu Select one of the alternatives ASTRA, HOTBIRD, SIRIUS or THOR when you have a single LNB directed towards any of these sat- ellites. Pressing OK from the selected alternative will display the “An- tenna adjustment” menu (shown to the right) on the screen. For each satellite, (e.g. ASTRA, HOTBIRD, SIRIUS, THOR), up to 4 different channels are preprogrammed and shown in the menu. When you adjust the a
Summary of the content on the page No. 15
FIRST TIME INSTALLATION Line and on the antenna satellite 5 6 selection menu Select one of these alternatives when you have a single antenna equipped with 2 LNBs, or two antennas with one LNB on each, and want to watch channels from ASTRA/HOTBIRD or THOR/ SIRIUS. In this case you must first connect the LNBs to an external switch since there is only one antenna input on the Mediamaster. Once installed the switch automatically selects the correct LNB for the selected channel. This ext
Summary of the content on the page No. 16
FIRST TIME INSTALLATION Line 7 on the antenna satellite selection Menu This selection is necessary only when your satellite choice dif- fers from the preprogrammed satellite alternatives in the follow- ing ways; • if you do not use an universal LNB • when you have more than two LNB’s. •You also must select this alternative when your antenna is con- trolled by motor (ref. to page 20.) One antenna/one LNB configuration OK Select this alternative if you have one (1) LNB mounted on the antenna a
Summary of the content on the page No. 17
FIRST TIME INSTALLATION Multisatellite/”mini DiSEqC” and “two port DiSEqC” Select one of these alternatives when your antenna system has two LNBs and when you not use any of the alternatives on the lines 5 - 6 from the menu “Antenna/satellite selection” on page 13. ☛ ☛ For each LNB you connect to the DiSEqC switch, the fol- lowing configuration has to be performed. As an example the following part will describe how the LNB in- tended for Hispasat will be configured to the DiSEqC input 1 (A) on
Summary of the content on the page No. 18
FIRST TIME INSTALLATION Multisatellite/four port DiSEqC Select this alternative if your antenna system has four LNBs and when you are not using any of the alternatives on the lines 5 - 6 from the menu “Antenna/satellite selection” on page 13. The selection of the different LNBs must be controlled by an external DiSEqC switch. Refer to page 15. The procedure is the same as for mini DiSEqC and two port☛ DiSEqC, but you have to configure four LNBs the same way as described on page 17. Connection of
Summary of the content on the page No. 19
FIRST TIME INSTALLATION Manual search When you perform a Manual search you first need to enter some parameters for the channel search to work. The information you need to enter in this menu is available in magazines covering satellite TV reception, on the Internet or from your Service Provider. Transponder frequency: Specify the frequency in GHz. If you enter the wrong figure(s), erase with the button. Polarization: Select Horizontal, Vertical, Circular left or Circular right. Symbol rate (MSym
Summary of the content on the page No. 20
FIRST TIME INSTALLATION Motor antenna In case you have an antenna motor to control your satellite an- tenna you have to make the following settings. If the antenna is prevented from reaching its predefined east/west limit positions, you have to set new limits. See page 37 for instructions. • From the “Antenna/Satellite selection” menu select line 7 (re- fer to page 13) and press OK. • Select line 5, “Motor antenna configuration” and press OK. Type of motor • Select SATSCAN if it is a Nokia SatSc
