Summary of the content on the page No. 1
1004624 SUB-FRAME MOUNTING KIT
Woods Backhoe Model:
BH6500/7500
mounting to
Kubota Tractor Model:
MX5000
2WD & FWA
equipped with or without:
Woods Loaders:
1009
1012
1016
Kubota Loaders:
LA852-1
LB702
MAN0094
MAN0094 (11/15/2002)
Summary of the content on the page No. 2
TO THE DEALER: Assembly and proper installation of this product is the responsibility of the WOODS dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Warranty Registration included in this manual. Both dealer and customer must sign the registration which certifies that all Dealer Check List items have been completed
Summary of the content on the page No. 3
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 HYDRAULIC INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Check that all hardware is properly installed. Safety is a primary concern in the design and Always tighten to torque chart specifications manufacture of our products. Unfortunately, our unless instructed otherwise in this manual. efforts to provide safe equipment can be wiped Air in hydraulic systems can cause erratic oper- out by an operator’s single careless act. ation and allows loads or equipment components In addition to th
Summary of the content on the page No. 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Remove seat and upper support assembly The only time the backhoe may be operated from a position other than the operator seat is dur- before installing or removing backhoe from tractor. ing backhoe attachment and removal. Operator Failure to comply may result in equipment failure must and/or personal injury. Read Mounting Kit Manual instructions on If tractor is equipped with draft sensing control, attaching and removing back
Summary of the content on the page No. 6
BACKHOE SUB-FRAME INSTALLATION Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act. ■ Only use 1004624 Sub-Frame Mounting Kit for In addition to the design and configuration of mounting Woods BH6500/7500 backhoe on equipment, hazard control and accident preven- Kubota MX5000 tractor equipped with or without tion are dependent upon the awareness, concern, Woo
Summary of the content on the page No. 7
SUB-FRAME INSTALLATION Cont’d CAUTION Always wear relatively tight and belted cloth- ing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appro- priate. Figure 1 Sub-Frame Clearance Tractor Preparation NOTE: For installing this sub-frame, reference to right, left, forward and rearward directions are deter- mined from the operator’s position in the tractor seat.
Summary of the content on the page No. 8
SUB-FRAME INSTALLATION Cont’d Install Front Mount For Tractors with Kubota LA852 and LB702 or 2. 1000556 Front hanger Woods 1009, 1012, 1016 Loaders (Figure 2) 3. 1000562 Mounting plate 9. 1004627 Spacer 1. Install front hanger (2) to bottom of tractor between right and left loader mounts using two 17. 57816 1/2 Hardened flat washer cap screws (18) and flat washers (17). 18. 65505 M12 x 1.25P x 30mm Cap screw 19. 46070 9/16 Hardened flat washer thick 2. Secure front hanger to right side of l
Summary of the content on the page No. 9
SUB-FRAME INSTALLATION Cont’d Install Rear Hanger Bracket A. ----- Drawbar frame 1. Install rear hanger bracket (4) under tractor, B ----- PTO Drive housing between the drawbar frame (A) and the mid PTO 4. 62977 Rear hanger bracket drive housing (B) (if equipped). 19. 46070 9/16 Flat washer, hardened (2) 2. Position rear hanger bracket with the slots to the 21. 16087 M14 x1.5 x 35mm Cap screw (2) rear of the tractor. Secure with cap screws (21) and flat washers (19). 4 Rear Mount B 4 CD6130-
Summary of the content on the page No. 10
SUB-FRAME INSTALLATION Cont’d Install Rear Mount 1. Slide rear mount (5) into slots of rear hanger 4. 62977 Rear hanger bracket bracket (4). 5. 1004628 Rear mount 2. Pivot rear mount upward and secure to tractor with clevis pins from lower lift arms (removed dur- ing tractor preparation). Clevis Pin 4 5 DP3 LA1 Figure 7 Rear Mount Installed Figure 6 Rear Mount Installation (Typical) Sub-Frame Fit-Up 1. Center sub-frame under tractor. 8. 37827 Clevis pin, .75 x 3.14 15. 2688 Hair pin cott
Summary of the content on the page No. 11
SUB-FRAME INSTALLATION Cont’d Sub-Frame Fit-Up 1. Rotate front end of sub-frame up into the front 7. 37771 Bent pin .75 x 11.36 hanger. 16. 62043 Klik pin, 1/4 x 1-3/4 NOTE: Adjust front hanger as necessary to allow alignment with sub-frame. 2. Align front hanger and sub-frame. Install bent pin (7) and klik pin (16) as shown in Figure 10. 3. Once sub-frame is secured into position with bent pin, check fit-up and adjust as necessary. 4. Tighten all hardware to specifications given below. 5.
Summary of the content on the page No. 12
SUB-FRAME INSTALLATION Cont’d Attach Sub-Frame to Backhoe 1. Align six holes on the backhoe with holes on sub- 25. 1450 3/4 Hex nut frame. 26. 57798 3/4 Hardened flat washer 27. 735 3/4 NC x 2 Cap screw 2. Secure with six cap screws (27), hardened flat washers (26), and hex nuts (25) as shown. 3. Tighten according to specifications given below. 25 27 26 27 26 25 CD6130-3 DP8 Figure 13 Sub-Frame to Backhoe Installed Figure 12 Sub-Frame to Backhoe Hardware TORQUE SPECIFICATIONS Wrench C
Summary of the content on the page No. 13
HYDRAULIC INSTALLATION Keep hands and body away from pressurized Make sure all hydraulic hoses, fittings, and lines. Use paper or cardboard, not hands or other valves are in good condition and not leaking body parts to check for leaks. Wear safety gog- before starting power unit or using equipment. gles. Hydraulic fluid under pressure can easily Check and route hoses carefully to prevent dam- penetrate skin and will cause serious injury or age. Hoses must not be twisted, be
Summary of the content on the page No. 14
SUB-FRAME & BACKHOE INSTALLATION TO TRACTOR Mount Sub-Frame & Backhoe to Tractor This mounting kit is designed to provide Remove seat and upper support assembly secure mounting and adequate operator clear- before installing or removing backhoe from trac- ance when properly installed. Check clearance tor. Failure to comply may result in equipment dimensions shown in figure 1 to be sure you have failure and/or personal injury. installed mounting kit correctly. Follow all mount-
Summary of the content on the page No. 15
SUB-FRAME & BACKHOE REMOVAL FROM TRACTOR Remove Backhoe With Sub-Frame Remove seat and upper support assembly The only time the backhoe may be operated before installing or removing backhoe from trac- from a position other than the operator seat is tor. Failure to comply may result in equipment during backhoe attachment and removal. Opera- failure and/or personal injury. tor must Read Sub-Frame Mounting Kit Manual instructions on attaching and removing back- hoe and use ext
Summary of the content on the page No. 16
SUB-FRAME & BACKHOE INSTALLATION TO TRACTOR Store Hydraulic Pump 1. Disconnect pump (1) from tractor PTO. 2. Rotate pump and insert pin on pump mounting bracket through outside hole on foot rest as 1 shown in Figure 16. 3. Secure pump bracket to foot rest (2) with klik pin (16). 16 2 1. Pump 2. Backhoe foot rest 16. 62043 1/4 x 1-3/4 Klik pin CD4868 Figure 16 Hydraulic Pump Storage NOTES MAN0094 (11/15/2002) 14 Installation
Summary of the content on the page No. 17
1004624 SUB-FRAME MOUNTING KIT 8 15 25 27 5 26 4 19 20 19 21 3 CD6130 23 9 2 6 19 1 24 3 17 16 Serial Number Plate 1 18 Located inside sub-frame side rail, rear of cross tube 22 MODELNO. SERIALNO. MASS (KG) ID NO. YR OF MFG. 16 OREGON, IL U.S.A. 7 REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1004637 1 Sub-Frame BH6500/7500 17 57816 2 1/2 Hardened flat washer 2 1000556 1 Front hanger assembly 18 65505 2 M12 x 1.25P x 30mm Cap screw 3 1000562 2 Mounting plate (used without loader) 19 46070
Summary of the content on the page No. 18
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware define
Summary of the content on the page No. 19
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 5/8 3/4 7/8 IN 1 2 3 4 5 6 7 MM 25 50 75 100 125 150 175 Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG.............................................................Agriculture NC.................................................... National Coarse ATF.............................. Automatic Transmission Fluid NF ...
Summary of the content on the page No. 20
WARRANTY (Replacement Parts For All Models Except Mow’n Machines) WEC Company, d/b/a Woods Equipment Company (“WOODS”), warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months. Under no circumstances will this Warranty apply in the event that the product, in the good
