Summary of the content on the page No. 1
Installation and Assembly:
Full Service Video Wall Mount
Model: DS-VW760
COLLAPSED
EXTENDED
Maximum Load Capacity: 150 Ib ( 68 kg)
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
1 of 14
Summary of the content on the page No. 2
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor. • This product should only be installed
Summary of the content on the page No. 3
Vertical Spacing Location If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine vertical spacing. T o determine lower mounting slot position of second mount, add display height to (Y1 ) or (Y2 ) DISPLAY HEIGHT H 10.25 1.688 X Y2 Y1 .938 Vertical Location X - 10.25 + (.938 OR 1.688) = (Y1 OR Y2) Horizontal Spacing Location If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine horizontal spacing. T
Summary of the content on the page No. 4
Parts List A B C Description Qty. Part # A pull out mount assembly 1 145‐1104 B adapter bracket 2 145‐1105 C lock bracket 2 145‐1091 D M5 x 10 mm socket pin type‐F screw 2 520‐1164 E #14 x 2.5" hex head wood screw 4 5S1‐015‐C03 F concrete anchor 4 590‐0320 G fender washer 4 540‐1008 H nylon shoulder washer 4 590‐2233 I M6 x 12 mm phillips screw 4 520‐1128 J M8 x 15 mm phillips screw 4 520‐9257 K 4 mm allen wrench 1 560‐9646 L cable tie (not shown) 2 560‐9711 M mesh sleeve (not shown) 1
Summary of the content on the page No. 5
Removing Display Carriage Remove display carriage by removing clip, pull release pin, and screws as shown. Remove screws using 2 4 mm allen wrench (K ). ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10 5 of 14 CLIP DISPLAY CARRIAGE SCREWS VIDEO W ALL MOUNT ASSEMBL Y LOCKING T AB RELEASE PIN VIDEO W ALL DISPLAY CARRIAGE MOUNT ASSEMBL Y LOCKING T AB
Summary of the content on the page No. 6
Installation to Wall Stud WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • T ighten wood screws so that wall plate is firmly attac hed, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud. The use of an "edge
Summary of the content on the page No. 7
Installation to Solid Concrete or Cinder Block WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used
Summary of the content on the page No. 8
Re-Attaching Display Carriage Secure display carriage by pulling release pin, fastening clevis pin, clip, four screws, and spacer as shown. 4 NOTE: make sure that spacer is in-between display carriage and video wall mount assembly. Attaching Adapter Brackets to Display Attach adapter brackets (B ) to back of display using four M6 x 12 mm phillips screws (I ) with nylon shoulder washer (H ), or four 5 M8 x 15 mm phillips screws (J ) as shown below . NOTE: Hardware to attach dedicated plates
Summary of the content on the page No. 9
Attaching Adapter Brackets to Display Carriage Attach adapter brackets (B ) to display carriage. Slide adapter brackets (B ) to position based on hole pattern as shown below . 6 Loosely fasten in place using security screw as shown in detail 1. NOTE: Once display is located in desired position, tighten security screws using 4mm allen wrench (K ) to lock in place. B B B Horizontal Display Position OPTIONAL GUIDE: When positioning adapter brackets make sure outside edge of adapter brac
Summary of the content on the page No. 10
Display Carriage Adjustment Use legend below to determine position of display. 7 NOTE: Each knob can be adjusted independently for fine tuning adjustments. Turn knob CLOCKWISE to tighten Turn knob COUNTER-CLOCKWISE to loosen UP DOWN ROTATE LEFT ROTATE RIGHT ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10 10 of 14
Summary of the content on the page No. 11
Adapter Bracket Adjustment Use legend below to determine position of display. 8 NOTE: Each knob can be adjusted independently for fine tuning adjustments. Turn knob CLOCKWISE to tighten Turn knob CLOCKWISE to tighten Turn knob COUNTER-CLOCKWISE to loosen Turn knob COUNTER-CLOCKWISE to loosen OUT IN TILT FORWARD TOP TOP TOP BACK BACK BACK UP DOWN TILT BACKWARD TILT RIGHT TILT LEFT TOP TOP TOP BACK BACK BACK ROTATE LEFT ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10 11 of 14
Summary of the content on the page No. 12
Cable Management Display cables can be routed through top or bottom of video wall mount assembly. 9 NOTE: Use mesh sleeve (M ) and cable ties (L ) for cable management as shown in detail 3 NOTE: Cable ties and cable management slots on video wall mount assembly can be used to secure display cables. TILT FOWARD M L TILT LEFT ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10 12 of 14 CABLE THR OUGH TOP DISPLAY CABLES VIDE O WALL M OUNT ASSEMBLY DETAIL 3 DISPLAY CABLE MANAGEMENT
Summary of the content on the page No. 13
Open and Close Display Carriage Open display carriage by releasing locking pin. Once open push down on access bracket to lock display carriage in place. 10 NOTE: Make sure that access bracket is notch in display carriage as shown in detail 4. Close Display Carriage Close display carriage by pulling up on access bracket to unlock display carriage. Once unlocked close display carriage. NOTE: Make sure that access bracket is out of notch in display carriage before closing. ISSUED: 04-23-10
Summary of the content on the page No. 14
Secure locking tab using two socket pin screws (D ) as shown below . 11 Lock bracket (C ) and lock (not supplied) can be used to secure display carriage to video wall mount assembly as shown in below. Optional C D C ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10 14 of 14 SLOT IN VIDEO W ALL MOUNT ASSEMBL Y VIDEO W ALL MOUNT ASSEMBL Y LOCK (NOT SUPPLIED) LOCKING T AB
