Summary of the content on the page No. 1
User’s Guide
™
V-Lock Wall Mount Assembly Kit
®
Replacement accessory for Extron System INTEGRATOR
SI 26 and SI 28 Surface Mount Speakers
68-1364-01
Rev. A
01 07
Summary of the content on the page No. 2
Introduction Packaging Information ™ The V-Lock Assembly Kit is supplied as two individual mounting kits (one in each inner box), and an Allen hex tool. Allen Hex Tool Wall Mount Assemblies Outer Packaging ™ Figure 1 — V-Lock Assembly packaging details ™ About the V-Lock Assembly Kit ™ The V-Lock Wall Mount Assembly Kit is a pair of replacement wall mounting kits (wall plate and locking stage only) for the ® Extron System INTEGRATOR SI 26 and SI 28 two-way surface mount speakers. Secondary
Summary of the content on the page No. 3
Installation ™ Installing the V-Lock Assembly Kit If your speakers are not already installed, follow the instructions outlined in the SI 26 and SI 28 User's Guide supplied with the speakers (or online at www.extron.com). ™ If your speakers are already installed, replace the V-Lock assembly by following the instructions, below. N Referring to packaging information for location, carefully remove and check contents before installation. N Extron recommends that the wiring installation is perfo
Summary of the content on the page No. 4
Installation, cont'd 5. Carefully remove (and retain) the mounting screws, taking care not to damage the mounting holes in the wall. Remove the mount from the wall. ™ 6. Remove a new V-Lock assembly from its box, loosen the hex cap screw and rotate the front section approximately 90 degrees to the mounting plate, (see figure 3). Lightly tighten the hex cap screw to temporarily lock it in position, allowing access to the mounting holes in the wall plate. 7. Pass the wire through the acce
Summary of the content on the page No. 5
...and slide it down Lift the speaker up to the into the V-lock groove. wall mount assembly.... Box Box Bracket Bracket V Lock Groove V Lock Groove Figure 5 — Slide the speaker down onto the wall mount assembly 2. If re-installing two speakers, repeat all the installation and speaker mounting steps for the second speaker, then go to "Final adjustments" section on the following page. Mounting the SI 28 speaker onto the wall mount assembly 1a. Carefully lift the speaker up as close to the botto
Summary of the content on the page No. 6
Installation, cont’d Final adjustments 1. When the speaker is in place, insert the audio wires into the back of the speaker as shown. E Exxttrroon n Push down on the spring terminals at the back of the speaker, and insert INPUT Negative the wires. Release the springs to secure. Wire Positive Wire Figure 7 — Insert audio wires into the terminals If the ends of the wires are damaged and need to be N restripped, follow the instructions in the SI 26 and SI 28 User's Guide. 2. Turn on the au
Summary of the content on the page No. 7
Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of five years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned withi
Summary of the content on the page No. 8
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan 1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Rd. #04-01 Kyodo Building, 16 Ichibancho Anaheim, CA 92805 3821 AH Amersfoort, The Netherlands PM Industrial Bldg., Singapore 368363 Chiyoda-ku, Tokyo 102-0082 800.633.9876 714.491.1500 +800.3987.6673 +31.33.453.4040 +800.7339.8766 +65.6383.4400 Japan FAX 714.491.1517 FAX +31.33.453.4050 FAX +65.6383.4664 +81.3.3511.7655 FAX +81.3
