Summary of the content on the page No. 1
T200U-NOy ANALYZER
ADDENDUM
(for use with T200 Operators Manual, PN 06858
and with the T200U Addendum, PN 06861)
© TELEDYNE ADVANCED POLLUTION INSTRUMENTATION
9480 CARROLL PARK DRIVE
SAN DIEGO, CA 92121-5201
USA
Toll-free Phone: 800-324-5190
Phone: 858-657-9800
Fax: 858-657-9816
Email: api-sales@teledyne.com
Website: http://www.teledyne-api.com/
Copyright 2011-2013 07303C DCN6646
Teledyne Advanced Pollution Instrumentation 06 February 2013
Summary of the content on the page No. 2
Summary of the content on the page No. 3
SAFETY MESSAGES Important safety messages are provided throughout this manual for the purpose of avoiding personal injury or instrument damage. Please read these messages carefully. Each safety message is associated with a safety alert symbol, and placed throughout this manual and inside the instrument. The symbols with messages are defined as follows: WARNING: Electrical Shock Hazard HAZARD: Strong oxidizer GENERAL WARNING/CAUTION: Read the accompanying message for specific in
Summary of the content on the page No. 4
CONSIGNES DE SÉCURITÉ Des consignes de sécurité importantes sont fournies tout au long du présent manuel dans le but d’éviter des blessures corporelles ou d’endommager les instruments. Veuillez lire attentivement ces consignes. Chaque consigne de sécurité est représentée par un pictogramme d’alerte de sécurité; ces pictogrammes se retrouvent dans ce manuel et à l’intérieur des instruments. Les symboles correspondent aux consignes suivantes : AVERTISSEMENT : Risque de choc électrique D
Summary of the content on the page No. 5
WARRANTY WARRANTY POLICY (02024F) Teledyne Advanced Pollution Instrumentation (TAPI), a business unit of Teledyne Instruments, Inc., provides that: Prior to shipment, TAPI equipment is thoroughly inspected and tested. Should equipment failure occur, TAPI assures its customers that prompt service and support will be available. COVERAGE After the warranty period and throughout the equipment lifetime, TAPI stands ready to provide on-site or in-plant service at reasonable rates similar to
Summary of the content on the page No. 6
Model 200EU-NOy Option Manual Addendum This page intentionally left blank. iv 07303C DCN6646
Summary of the content on the page No. 7
Model 200EU-NOy Option Manual Addendum TABLE OF CONTENTS 1.0 INTRODUCTION ......................................................................................................7 2.0 SPECIFICATIONS ...................................................................................................9 2.1 Specifications ........................................................................................................................9 3.0 GETTING STARTED................................
Summary of the content on the page No. 8
Model 200EU-NOy Option Manual Addendum List of Figures Figure 1. Rear Panels: T200U-NOy Analyzer (top) and 501Y (center); Converter (bottom)......................13 Figure 2. Rear Panel Pneumatic Connections............................................................................................14 Figure 3. Replacing the Particulate Filter...................................................................................................25 Figure 4. NOy Converter Guts Assembly Locatio
Summary of the content on the page No. 9
1.0 INTRODUCTION The T200U-NOy analyzer consists of an external Converter designed to support a NOx analyzer by converting multiple, unstable compounds grouped under the name NOy. The converter is mounted externally at the sample inlet to minimize flow time between sample in and converter, thereby optimizing measurement accuracy. This manual addendum is to be used in conjunction with two additional documents with operation instructions: T200 operation manual (part number 06858)
Summary of the content on the page No. 10
Model T200EU-NOy Option Manual Addendum 1.0 Introduction This page intentionally left blank. 8 07303C DCN6646
Summary of the content on the page No. 11
2.0 SPECIFICATIONS 2.1 Specifications Table 1 Specifications for the External Converter and the 501Y Bypass Pump Converter Remotely mounted molybdenum external Converter with temperature controller in a NEMA – 4 enclosure. o o Converter Temperature 315 C 7 C with read-out on front panel of bypass pump chassis. Tube/Electrical Cable Up to 50 feet (15 m) maximum length Assembly Power, 501Y Bypass Pump 120V~ 60 Hz, 230V~ 50 Hz 360 watts Assembly Power, Converter Assembly 120V~ 50
Summary of the content on the page No. 12
Model T200EU-NOy Option Manual Addendum 2.0 Specifications This page intentionally left blank. 10 07303C DCN6646
Summary of the content on the page No. 13
3.0 GETTING STARTED The NOy converter has been designed to operate with the T200U low level NOx analyzer, with some additional modification.The combination is referred to as the T200U-NOy analyzer. 3.1 Unpacking and Inspection CAUTION! Avoid personal injury: use two persons each to lift and carry the analyzer and the Model 501 Pump Pack chassis. The T200U- NOy comes in three boxes: The analyzer with AC power cord 501Y Bypass Pump Chassis (typically referred to as “501Y he
Summary of the content on the page No. 14
Model T200U-NOy Option Manual Addendum 3.2 Electrical and Pneumatic Connections NOTE To maintain compliance with EMC standards, it is required that the cable length (at the rear of the analyzer) be no greater than 3 meters for all I/O connections, which include Analog In, Analog Out, Status Out, Control In, Ethernet/LAN, USB, RS-232, and RS-485. 1. Mount the Converter (Figure 1, bottom) on a suitable mast. 2. Route the umbilical cable assembly into the shelter of the Converter. 3. Lo
Summary of the content on the page No. 15
Model T200U-NOy Option Manual Addendum Figure 1. Rear Panels: T200U-NOy Analyzer (top) and 501Y (center); Converter (bottom) 07303C DCN6646 13
Summary of the content on the page No. 16
Model T200U-NOy Option Manual Addendum Figure 2. Rear Panel Pneumatic Connections Note: Pneumatic tubes and rear panel labels include numbers to facilitate matching connections between instruments. CONNECTIONS: Analyzer to Pump to Converter and Calibrator to Pump Calibrator Analyzer Pump Chassis Converter NO IN (1) NO OUT (1) NOY IN (2) NOY OUT (2) [cal gas out port] CAL IN (3) NOY IN (4) NO OUT (4) NO IN (5) NOY OUT (5) CAL OUT (6) CAL IN (6) 14 07303C DCN6646
Summary of the content on the page No. 17
Model T200U-NOy Option Manual Addendum 3.3 Initial Operation 1. After confirming proper supply voltage, turn on the power to the analyzer and the 501Y bypass pump, and plug in the external Pump. If you are unfamiliar with the T200U-NOy analyzer, we recommend that you read the overview in Section 3 of its operation manual before proceeding. The front panel displays should immediately light as the instruments start up. The 501Y requires about 30 minutes for the external Converter t
Summary of the content on the page No. 18
Model T200U-NOy Option Manual Addendum This page intentionally left blank. 16 07303C DCN6646
Summary of the content on the page No. 19
4.0 THE T200U-NOY EXTERNAL CONVERTER 4.1 Principle of Operation The T-API Model T200U-NOy is designed to measure the concentration of NO, NO , and other compounds that are too unstable to be measured when taken in 2 through the normal ambient air sample inlet system. Please refer to the T200U manual supplied with this system for a general discussion of the operation of a NOx analyzer. The suite of compounds known collectively as NOy is composed of roughly 30 compounds. The NOy meas
Summary of the content on the page No. 20
Model T200U-NOy Option Manual Addendum This page intentionally left blank. 18 07303C DCN6646
