Summary of the content on the page No. 1
INSTRUCTION MANUAL
MODEL 200EH/EM
NITROGEN OXIDES ANALYZER
© TELEDYNE ADVANCED POLLUTION INSTRUMENTATION
9480 CARROLL PARK DRIVE
SAN DIEGO, CA 92121-5201
USA
Toll-free Phone: 800-324-5190
Phone: 858-657-9800
Fax: 858-657-9816
Email: api-sales@teledyne.com
Website: http://www.teledyne-api.com/
04521
Rev. C
DCN 5731
Copyright 2007-2010 14 May 2010
Teledyne Advanced Pollution Instrumentation
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Teledyne API - Model 200EH/EM Operation Manual Safety Messages SAFETY MESSAGES Your safety and the safety of others is very important. We have provided many important safety messages in this manual. Please read these messages carefully. A safety message alerts you to potential hazards that could hurt you or others. Each safety message is associated with a safety alert symbol. These symbols are found in the manual and inside the instrument. The definition of these symbols is described
Summary of the content on the page No. 4
This page intentionally left blank. ii 04521C (DCN5731)
Summary of the content on the page No. 5
Teledyne API - Model 200EH/EM Operation Manual Table of Contents TABLE OF CONTENTS 1. M200EH/EM Documentation....................................................................................................................................................1 1.1. Using This Manual............................................................................................................................................................1 2. Specifications, Approvals and Warranty..............
Summary of the content on the page No. 6
5.11. Alarm Relay Option (OPT 67).......................................................................................................................................51 5.12. Special Software Features ...........................................................................................................................................53 5.12.1. Maintenance Mode Switch..........................................................................................................................
Summary of the content on the page No. 7
Teledyne API - Model 200EH/EM Operation Manual Table of Contents 6.13.5.1. The Analog I/O Configuration Submenu. ....................................................................................................113 6.13.5.2. Analog Output Signal Type and Range Selection.......................................................................................115 6.13.5.3. Turning the Analog Output Over-Range Feature ON/OFF.........................................................................
Summary of the content on the page No. 8
9.3.2. Changing the O Dryer Particulate Filter...............................................................................................................179 3 9.3.3. Maintaining the External Sample Pump................................................................................................................180 9.3.3.1. Rebuilding the Pump.....................................................................................................................................180 9.3.3.2. C
Summary of the content on the page No. 9
Teledyne API - Model 200EH/EM Operation Manual Table of Contents 10.4.13. Power-up Circuit ...............................................................................................................................................221 10.5. Power Distribution &Circuit Breaker ...........................................................................................................................222 10.6. Communications Interface............................................................
Summary of the content on the page No. 10
11.5.12. PMT Sensor......................................................................................................................................................263 11.5.13. PMT Preamplifier Board ...................................................................................................................................263 11.5.14. High Voltage Power Supply ...........................................................................................................................
Summary of the content on the page No. 11
Teledyne API - Model 200EH/EM Operation Manual List of Figures Figure 5-11: M200EH/EM Ethernet Card .........................................................................................................50 Figure 5-12: M200EH/EM Rear Panel with Ethernet Installed.........................................................................50 Figure 5-13: Alarm Relay Output Pin Assignments..........................................................................................52 Figure 6-6-1: F
Summary of the content on the page No. 12
Figure 10-10-25: Power Distribution Block Diagram ........................................................................................... 222 Figure 10-10-26: Interface Block Diagram ........................................................................................................... 223 Figure 10-10-27: M200EH/EM Front Panel Layout.............................................................................................. 224 Figure 10-10-28: Keyboard and Display Interface Block
Summary of the content on the page No. 13
Teledyne API - Model 200EH/EM Operation Manual List of Tables Table 6-6: Front Panel LED Status Indicators for iDAS................................................................................63 Table 6-7: iDAS Data Channel Properties ....................................................................................................64 Table 6-8: iDAS Data Parameter Functions..................................................................................................65 Table 6-9: M20
Summary of the content on the page No. 14
LIST OF APPENDICES APPENDIX A - VERSION SPECIFIC SOFTWARE DOCUMENTATION APPENDIX A-1: M200EH/EM Software Menu Trees, Revision F.0 APPENDIX A-2: Setup Variables For Serial I/O, Revision F.0 APPENDIX A-3: Warnings and Test Functions, Revision F.0 APPENDIX A-4: M200EH/EM Signal I/O Definitions, Revision F.0 APPENDIX A-5: M200EH/EM iDAS Functions, Revision F.0 APPENDIX A-6: Terminal Command Designators, Revision F.0 APPENDIX B - M200EH/EM SPARE PARTS LIST APPENDIX C - REPAIR QUESTIONNA
Summary of the content on the page No. 15
Teledyne API - Model 200EH/EM Operation Manual M200EH/EM Documentation 1. M200EH/EM DOCUMENTATION Thank you for purchasing the Model 200EH/EM Nitrogen Oxides Analyzer! The documentation (part number 04521) for this instrument is available in several different formats: Printed format, or; Electronic format on a CD-ROM. ® ® The electronic manual is in Adobe Systems Inc. “Portable Document Format” (PDF). The Adobe Acrobat ® Reader software, which is necessary to view these files, can b
Summary of the content on the page No. 16
M200EH/EM Documentation Teledyne API - Model 200EH/EM Operation Manual 6.0 Operation Instructions Step by step instructions for operating the analyzer. 7.0 Calibration Procedures General information and step by step instructions for calibrating your analyzer. 8.0 EPA Protocol Calibration Because there is no single, standard method for EPA equivalency in application where high concentrations of NO are measured, no specific EPA calibration/validation method is included in this manual. x 9
Summary of the content on the page No. 17
Teledyne API - Model 200EH/EM Operation Manual Specifications, Approvals and Warranty 2. SPECIFICATIONS, APPROVALS AND WARRANTY 2.1. M200EH/EM OPERATING SPECIFICATIONS Table 2-1: Model 200EH/EM Basic Unit Specifications Min/Max Range 200EH: Min: 0-5 ppm; Max: 0-5000 ppm (Physical Analog Output) 200EM: Min: 0-1 ppm; Max: 0-200 ppm 3 Measurement Units ppm, mg/m (user selectable) Zero Noise <20 ppb (RMS) Span Noise <0.2% of reading above 20 ppm Lower Detectable Limit 40 ppb (2x noise as
Summary of the content on the page No. 18
Specifications, Approvals and Warranty Teledyne API - Model 200EH/EM Operation Manual 2.2. CE MARK COMPLIANCE Emissions Compliance The Teledyne-Advanced Pollution Instrumentation Nitrogen Oxides Analyzers M200EH/EM, M200EH/EMH and M200EH/EMM were tested and found to be fully compliant with: EN61326 (1997 w/A1: 98) Class A, FCC Part 15 Subpart B Section 15.107 Class A, ICES-003 Class A (ANSI C63.4 1992) & AS/NZS 3548 (w/A1 & A2; 97) Class A. Tested on January 02-06, 2003 at CKC Laboratorie
Summary of the content on the page No. 19
Teledyne API - Model 200EH/EM Operation Manual Specifications, Approvals and Warranty THE WARRANTIES SET FORTH IN THIS SECTION AND THE REMEDIES THEREFORE ARE EXCLUSIVE AND IN LIEU OF ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE OR OTHER WARRANTY OF QUALITY, WHETHER EXPRESSED OR IMPLIED. THE REMEDIES SET FORTH IN THIS SECTION ARE THE EXCLUSIVE REMEDIES FOR BREACH OF ANY WARRANTY CONTAINED HEREIN. API SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE
Summary of the content on the page No. 20
04521C (DCN5731)
