Summary of the content on the page No. 1
Dear Sceptre Customer,
Congratulations on your new SCEPTRE X405 HDTV purchase. Thank you
for your support. To ensure safety and many years of trouble free operation
of your TV, please read the manual carefully before making any adjustments,
and keep them in a safe place for future references. We hope you enjoy your
new SCEPTRE HDTV.
For technical assistance, please call 1800-788-2878 and select option 3 or
email our tech support group at SceptreTS@sceptre.co
Summary of the content on the page No. 2
IMPORTANT INFORMATION WARNING: The appliance coupler is used as disconnect device, the disconnect device shall remain readily operable. WARNING: The battery shall not be exposed to excessive heat such as sunshine, fire or the like. - 2 - www.SCEPTRE.com SCEPTRE X405 HDTV User Manual
Summary of the content on the page No. 3
SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and / or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning t
Summary of the content on the page No. 4
SAFETY INSTRUCTIONS This product is designed and manufactured to operate within defined design limits, and misuse may result in electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of the product. Read the following safety instructions before operating the display. Keep these instructions in a safe place for future reference. To avoi
Summary of the content on the page No. 5
Do not overload power strips and immediately and contact your dealer extension cords. Overloading can for repair. Continued use of the result in fire or electric shock. product may cause fire or electric The wall socket should be installed shock. near the equipment and should be Do not install the product in an area easily accessible. with heavy dust or high humidity. Only the marked power source can be Operating the product in environments used for the product. Any power with hea
Summary of the content on the page No. 6
IMPORTANT INFORMATION Television Antenna Connection Protection External Television Antenna Grounding If an outside antenna or cable system is to be connected to the TV, make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and static charges. Article 810 of the National Electrical Code, ANSI/NFPSA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in
Summary of the content on the page No. 7
Opening the Package The SCEPTRE TV is packaged in a carton. Any standard accessories are packed separately in another carton. The weight of the TV is approximately 39.7lb. Due to the size and weight of the product, it is suggested that it must be handled by a minimum of 2 or more persons. Since the glass can be easily scratched or broken, please handle the product gently. Never place the unit on a surface with the glass facing downwards unless it is on protective padding. When open
Summary of the content on the page No. 8
Attaching or Removing the Stand 1. To attach the stand place the display unit flat on a table. Afterwards attach the stand onto the display and screw in the 4 screws to secure the stand. 2. To remove the stand, remove the 6 screws in the circled area and the stand will come off. - 8 - www.SCEPTRE.com SCEPTRE X405 HDTV User Manual
Summary of the content on the page No. 9
Table of Contents IMPORTANT INFORMATION .............................................................................................................. 2 SAFETY INSTRUCTIONS .................................................................................................................... 3 SAFETY INSTRUCTIONS .................................................................................................................... 4 IMPORTANT INFORMATION .....................................
Summary of the content on the page No. 10
Identifying Front and Rear Panel Front View INDICATOR LIGHT – The light is red when power is plugged in but the TV is not turned on. The light turns blue when the TV is turned on. Because of the LCD in the panel, the TV might take 10 – 12 seconds to power on. REMOTE SENSOR – The remote sensor receives all the commands from the remote control. Rear View Mounting Pattern Mounting Specification : 400mm x 200mm using screw size M6
Summary of the content on the page No. 11
Side Control Buttons 1. VOL(+) – This button increases the TV’s volume. If a sub-menu is active, pressing this button will move the select right. 2. VOL(-) – This button decreases the TV’s volume. If a sub-menu is active, pressing this button will move the selection left. 3. CH(▲) – This button changes the TV channel up. If the OSD is active, this button functions as up for the menu. 4. CH(▼) – This button changes the TV chann
Summary of the content on the page No. 12
Rear View Connections 1. SPDIF - This connection port is used for sending out digital audio signals to digital surround sound receivers. The orange (COAX SPDIF OUT) connector sends out either bit-stream or PCM digital sound signal to a home theater receiver with digital coax input. 2. TV – This connection is for digital or analog cable without the cable box or over-the-airwave antennas. The tuner is a hybrid tuner that tunes to both analog an
Summary of the content on the page No. 13
streaming stick. Plug the ROKU stick to HDMI 3, and switch your source to HDMI3. Afterwards use the purple colored buttons to access ROKU functions. 6. USB – USB connects to USB flash drives for playing music and picture. The USB port is also used for updating the TV’s firmware. 7. YPbPr – This connection port is for DVD players or satellite / cable set-top boxes that use component cables. From left to right, connect green, blue, and red for video, and then connect white for left cha
Summary of the content on the page No. 14
SCEPTRE X405 Remote Control This remote control follows SONY’s universal remote code. To find the actual code you need to consult your cable or satellite tech support. - 14 - www.SCEPTRE.com SCEPTRE X405 HDTV User Manual
Summary of the content on the page No. 15
For universal remotes, this TV follows SONY’s universal remote code. You need to find the actual code from your cable or satellite or universal remote provider. The button order is from left to right. 1. POWER – Turns the TV on or off. 2. INFO – Shows the display info. 3. FREEZE – Press this button to freeze current picture. 4. SLEEP – Turns the TV off in a specific set of time dependent on your selection. 5. CC – Cycles between different closed captioning modes. 6. MTS – Selects
Summary of the content on the page No. 16
Installing Batteries to the Remote Control Please insert two AAA batteries into the remote control. Make sure that you match the (+) and (-) symbols on the batteries with the (+) and (-) symbols inside the battery compartment. Afterwards, re-attach the battery cover. Please note: Only use AAA batteries. Do not mix new and old batteries. This may result in cracking or leakage that may pose a fire risk or lead to personal injury. Inserting the
Summary of the content on the page No. 17
Connection Suggestions If You Have Digital Cable without Cable Box or Antenna… 1. Make sure the power of HDTV is turned off. 2. Connect the Coaxial RF cable from your antenna or digital cable to the TV port on the back of your HDTV. 3. Turn on the HDTV. 4. Follow the first time on screen instructions. Please Note : Not all broadcasts are in High Definition (HD). Please refer to your local broadcasting stations for more information. The
Summary of the content on the page No. 18
Connecting DVD Player with Component YPbPr… 1. Make sure the power of HDTV and your DVD player is turned off. 2. Obtain a Component Cable. Connect the green color connector to both your DVD player and YPbPr’s green connector port on the back of your HDTV. 3. Connect the blue color connector to both your DVD player and YPbPr’s blue connector port on the back of your HDTV. 4. Connect the red color connector to both your DVD player and YPbPr’s re
Summary of the content on the page No. 19
Connecting Wii™ with Composite… 1. Make sure the power of HDTV and your Wii™ is turned off. 2. Obtain a Yellow Video Cable. Connect the Yellow Video connector to both your Wii™ and AV’s Yellow Video connector port on the back side of your HDTV. 3. Obtain a RCA Audio Cable. Connect the white color connector to both your Wii™ and AV’s white connector port on the back side of your HDTV. 4. Connect the red color connector to both your Wii™ and AV
Summary of the content on the page No. 20
Connecting Cable or Satellite boxes with HDMI… 1. Make sure the power of HDTV and your set-top box is turned off. 2. Connect a HDMI cable to the HDMI output of your set-top box and the other end to the HDMI port on the back of your HDTV. 3. Turn on the HDTV and your set-top box. 4. Use the remote control’s source button or the source button on the TV to switch to HDMI. Please Note : Please reference the set-top box’s manual, to make
