SECO-LARM USA Central Receiver SK-910RC4Q user manual

Summary of the content on the page No. 1

SK-910RC4Q
Central Receiver
Manual


4 Channels 4 Relay output modes
4 Channel relay outputs 4 Programmable alert tones
1 Auxiliary relay output (12VDC) Up to 500’ (152m) range

Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.

Summary of the content on the page No. 2

ENFORCER SK-910RC4Q Central Receiver Table of Contents: Introduction ..................................................... 2 Alert Tones ..................................................... 4 Specifications ................................................. 2 Programming Each Channel Output ............... 5 Dimensions ..................................................... 2 Setting the Timed Output ................................ 6 Overview ............................................

Summary of the content on the page No. 3

ENFORCER SK-910RC4Q Central Receiver Overview: Power Input Programming buttons Mode button (12VDC) Top : To antenna Timer switches Front: Antenna Volume adjustment knob Speaker Status LEDs Bottom: Auxiliary relay output (12VDC) Main relay outputs Installation Notes: 1. Mount in a convenient location where alert tones and LED indicators will be audible/visible. 2. Do not install in a location surrounded by metal as RF signals may be blocked, decreasing

Summary of the content on the page No. 4

ENFORCER SK-910RC4Q Central Receiver Code Learning a New Transmitter: Each receiver channel can learn the codes of up to 15 different transmitters. Transmitters are learned on a first-in, first-out basis. (For example, if 15 transmitter codes have been learned, when a new transmitter is learned the first of the 15 codes that were learned before will be deleted.) 1. To learn a new transmitter, first press and hold the programming button of the channel to be programmed for 3 seconds

Summary of the content on the page No. 5

ENFORCER SK-910RC4Q Central Receiver Programming Each Channel Output: 1. Each channel output can be separately programmed for one of four different modes: Timed Output: When the channel receives a signal, the relay will turn ON for 1~60 seconds, depending on the output time set. Note: The timer, once set, is the same length for all outputs programmed for Timed Output. (See page 6 for timer programming.) Toggle Output: When the channel receives a signal, the relay will turn ON an

Summary of the content on the page No. 6

ENFORCER SK-910RC4Q Central Receiver Setting the Timed Output: When a channel is set to Timed Output, triggering the channel will activate the relay for a set period of time. Factory default is 1 second. 1. The time can be set from 1~60 seconds using the Timer switches on the top of the receiver. 2. Set switches according to the following chart. NOTE: The time set via the DIP switches applies to all channels programmed for Timed Output. Sec. SW1 SW2 SW3 Top of unit 1* On Off

Summary of the content on the page No. 7

ENFORCER SK-910RC4Q Central Receiver Setting the Power LED: The power LED can be set to Bright, Dim, or OFF using the power LED jumper. 1. Locate the jumper on the PCB as shown below. 2. Place the jumper on the middle and right pins for Dim, and on the middle and left pins for Bright. 3. Remove the jumper or place on the left or right pin only to set the power LED to OFF. Power LED jumper settings Jumper PCB Bright Off Dim Sample Applications: Recording station Outside driv

Summary of the content on the page No. 8

ENFORCER SK-910RC4Q Central Receiver Troubleshooting: The SK-910RC4Q will not read a Check that the transmitter is operating within the receiver’s range. transmitter it has already learned. Check number of transmitters learned. Learning more than 15 will cause the first transmitter learned to be deleted. Check that there are transmitter codes stored on the channel by pressing that channel’s programming button once and counting the flashes. The SK-910RC4Q is not in the correct P