Summary of the content on the page No. 1
SIP ND2100 Series
Single Line IP Phone User’s Guide
For Models: SIP ND2105, SIP ND2110, SIP ND2105S, SIP ND2110S, SIP ND210L
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY – WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE OR FRAYED.
RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING
– IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.
THE FOLLOWING:
– IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER
Summary of the content on the page No. 2
TAbLE OF CONTENTS 1. Introduction to the Teledex iPhone SIP ND2100 series 4.1.4 Adjust the ringer volume 6 IP phone 3 4.1.5 Adjust the speaker volume 6 1.1 Definitions, acronyms and abbreviations 3 4.1.6 Adjust the handset volume 7 1.2 The SIP ND2100 Series works like a telephone 3 4.2 Placing a phone call 7 1.3 The network 3 4.3 Receiving a phone call 7 1.4 The IP-PBX 3 4.4 Using Mute 7 1.5 The network system administrator 3 4.5 Using Hold 7 4.6 Transferring a call 7 2. Installing the SIP ND
Summary of the content on the page No. 3
1. Introduction to the Teledex iPhone SIP ND2100 CAUTION mean risk of damage to equipment. Whenever you Series IP Phone see this symbol, be aware of the steps that you will perform and be sure that you avoid the conditions that may damage The Teledex iPhone SIP ND2100 series IP phone is a the equipment. SIP-compliant network terminal. Instead of using standard analog or digital telephone lines, it connects to the network NOTES point out exceptions or additions to the information in t
Summary of the content on the page No. 4
2.5 Connecting the SIP ND2100 Series to the network 2.7 Arranging the SIP ND2100 Series on the Desk or Table WARNING! Risk of electrical shock! Dangerous voltages may Route the network cable toward the rear of the base of be present on the terminals of the network patch cable after the phone, and attach the desk/wall mounting bracket by it is plugged into the network wall jack. Connect the patch inserting the tabs into the matching holes in the base. Place cable to the base first, then to t
Summary of the content on the page No. 5
Figure 2 shows the welcome page of the configuration portal. The phone can be configured through the main menu provided by this portal. NOTE: Except for upgrading the software online (decribed in subsection 3.2.7), the configuration for the SIP ND2100 series will not be activated until the phone has been reset. Fig 4: Configuration of Speed Dial Keys 3.2.4 Configure the Call Features (Fig. 5) Fig 2: Teledex iPhone Configuration Portal The configurable call features include Do Not Disturb, C
Summary of the content on the page No. 6
Fig 5: Call Feature Configuration Fig 7: Reset the Phone 3.2.5 Upgrade the Phone’s Firmware (Fig.6) 3.2.7 Restore to Factory Configuration To update the phone’s firmware through the configuration To restore the phone to the factory (default) configuration portal, click “Online Upgrade” on the left menu. via the configuration portal, follow these steps: 1. Click “Restore to Factory” on the left menu. There are three update options from which to choose: 2. Click “Restore” to restore factory set
Summary of the content on the page No. 7
4.1.6 Adjusting the Handset Volume Note: Alternatively, it is not necessary to wait for the third party to answer before transferring a call. To make a “blind Activate the handset by picking it up. With the handset transfer,” simply hang up while the other party’s phone is active, press the up or down arrow key to raise or lower ringing, and the third party will pick it up as any other handset volume to the desired level. incoming call. 4.2 Placing a Phone Call 4.7 Redialing the Last N
Summary of the content on the page No. 8
5.3.1 Programming the Memory Dialing Keys Through ADVANCED FEATURES the Concealed STORE Key 5.5 Using Voice Mail The speed dial keys can be programmed not only through the configuration portal (as described by subsection 3.2.3) 5.5.1 Message Waiting but also through the concealed STORE key. If the red message waiting indicator is flashing slowly, voice mail messages are waiting to be retrieved. The STORE key is concealed to deter unauthorized tampering. With the clear plastic overlay and f
Summary of the content on the page No. 9
7. Appendix A – European Requirements 9. Appendix C – Product Support If you need technical assistance with this product, This product complies with the following CE requirements: please contact Teledex via one of the following methods: 89/336/EEC EN 55024 Telephone EN 55022 EN 60950 (CB SCHEME) 408.363.3100 8. Appendix b – SIP ND2100 Series Product Specifications Email TELEPHONE TYPE support@teledex.com Single-line, Voice over Internet Protocol network terminal Internet www.teledex.co
Summary of the content on the page No. 10
Switched Port (Out) (Standard location; may Fig 1: SIP ND2100 Series Diagram vary by manufacture date) 10/100 Port (In) Switched Port (Alternate location; may vary by manufacture date) Speed Dial Keys (Configuration varies by model; not all keys may be present) Speaker (Under Handset) Pause (Recessed) Handset Store (Recessed) Dial Pad Volume Up/Down Redial Hold Messages Mute Microphone Speakerphone Flash (SIP ND2105S and ND2110S models only) 10
