Summary of the content on the page No. 1
SIP LD4100/4200 Series User Guide
For Models
SIP LD4105S, SIP LD4110S
SIP LD4205S, SIP LD4210S
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY – WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE OR FRAYED.
RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING
– IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.
THE FOLLOWING:
– IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER.
1. READ AND UNDERSTAND ALL I
Summary of the content on the page No. 2
TAbLE OF CONTENTS 1. Introduction to the Teledex iPhone SIP LD Series 4.1.2 Using the speakerphone 7 IP Phone 3 4.1.3 Switching between handset and speakerphone 7 1.1 Definitions, acronyms and abbreviations 3 4.1.4 Adjust the ringer volume 7 1.2 The SIP LD Series works like a telephone 3 4.1.5 Adjust the speaker volume 7 1.3 Two lines 3 4.1.6 Adjust the handset volume 7 1.4 The network 3 4.2 Placing a phone call 7 1.5 The IP-PBX 3 4.3 Receiving a phone call 7 1.6 The network system administ
Summary of the content on the page No. 3
1. Introduction to the Teledex iPhone SIP LD Series 2.1 A Matter of Safety IP Phone WARNINGS mean danger to persons and possibly, damage to The Teledex iPhone SIP LD series IP phone is a equipment. Whenever you see this symbol, be careful to study SIP-compliant network terminal. Instead of using standard the steps that you will perform, and be sure that you under- analog or digital telephone lines, it connects to the network stand the nature of the hazards before beginning the task. in the
Summary of the content on the page No. 4
2.4 Connecting the Handset a PC, it must be connected to the jack on the right side of the phone. Otherwise the phone will not function. Plug one end of the coil cord into the RJ-10 receptacle on the handset, and the other end into the receptacle on the left 2.7 Arranging the SIP LD Series on the Desk or Table side of the base. Place the handset into the cradle of the base. Route the network cable toward the rear of the base of 2.5 Connecting the SIP LD Series to the network the phone, and
Summary of the content on the page No. 5
Figure 2 shows the welcome page of the configuration portal. same phone number and configuration, and only Line 1 needs The phone can be configured through the main menu to be configured. To change the line configuration via the provided by this portal. configuration portal, follow these steps: 1. Click “Line 1 Info” or “Line 2 Info” on the left side menu. NOTE: Except for upgrading the software online (decribed in subsection 3.2.7), the configuration for the SIP LD series will 2. Input the r
Summary of the content on the page No. 6
3.2.5 Configure the Call Features (Fig. 6) The configurable call features include Do Not Disturb, Call Transfer, Call Forward No Answer, Call Forward Busy, Call Waiting, and Call Forward All. A call forward extension number can be pre-configured. A description of each feature is below: Do Not Disturb: The phone will not ring upon any incoming call. Call Transfer: Transfers the incoming call to another number or extension. Call Forward No Answer: The incoming call will be forwarded if
Summary of the content on the page No. 7
4.1.6 Adjusting the Handset Volume Activate the handset by picking it up. With the handset active, press the up or down arrow key to raise or lower handset volume to the desired level. 4.2 Placing a Phone Call There are various ways of initiating a phone call: 1. Lift the handset, listen for dial tone, and dial the phone number, using the keypad. 2. Press one of the LINE buttons (LINE 1 or LINE 2) activating the speakerphone. Dial the desired number. 3. Press the SPEAKER key. An avai
Summary of the content on the page No. 8
4.7 TRANSFERRING A CALL 5.2 USING CALL WAITING Note: This feature will not be valid unless it is enabled. Note: This feature will not be valid unless it is enabled through web portal configuration. The ND2210S can transfer an ongoing call to another phone on the same network if this feature is enabled through web If this feature was enabled through web portal configuration portal configuration. as described in subsection 3.2.5., you hear the call waiting tone during a call, on a single li
Summary of the content on the page No. 9
5.4 Three-Way Conference Calls 6.2.1 Disconnect From the Network The SIP LD series supports three-way conference calling. The Unplug the network cable from the wall jack. Wait at least CONF or FLASH key allows the user to include two fifteen (15) seconds, then plug the cable back into the same other parties in a three-way conversation. One three-way jack. The phone will attempt to re-establish contact with the conference could be done using only one line or both lines. IP-PBX. In many cases
Summary of the content on the page No. 10
Power 9. Appendix C – Product Support Power supplied from network switch (PoE), or from If you need technical assistance with this product, approved local power adapter please contact Teledex via one of the following methods: Telephone Dimensions & Weight 408.363.3100 W: 9.0” (22.86 cm) Email D: 8.5” (21.59 cm) support@teledex.com H: 6.47” (16.43 cm) full upright position 3.97” (10.08 cm) full flat position Internet www.teledex.com Wt: 2.80 lb. (1.27 Kg) If you feel that the i
