Summary of the content on the page No. 1
Installation Manual
Additional Cordless Handset
Model No. KX-TPA50
Thank you for purchasing a Panasonic product.
This unit is an additional handset compatible with the following
series of Panasonic SIP Cordless Phone:
KX-TGP500/KX-TGP550
You must register this handset with your base unit before it can
be used. This installation manual describes only the steps
needed to register and begin using the handset. For further
details, please read the base unit’s User Guide on the
Panasonic Web sit
Summary of the content on the page No. 2
Accessory information Supplied accessories Accessory item/Order number Quantity Charger/PNWETGP500B 1 AC adaptor/PQLV219Z or PQLV219 (03)Z 1 Rechargeable batteries/HHR-4DPA 2 (Part No. HHR-65AAABU or N4DHYYY00002) *1 Handset cover /PNYNTGA641TR 1 Belt clip/PNKE1029Z1 1 *1 The handset cover comes attached to the handset. Note: LPlease read the additional/replacement accessory section of the base unit’s User Guide on the Panasonic Web site. See page 1 for Panasonic URL. Setting up Connections (1
Summary of the content on the page No. 3
LThe AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) Battery installation/Battery charge Important: LUse the supplied rechargeable batteries. For replacement, we recommend using the Panasonic rechargeable batteries noted on page 2. LWipe the battery ends (S, T) with a dry cloth. LAvoid touching the battery ends (S, T) or the unit contacts. LConfirm correct polarities (S, T). LUSE ONLY Ni-MH batteries AAA (R03) size. LDo NOT use Alkaline/M
Summary of the content on the page No. 4
Registering a handset to the base unit 1 Base unit: NKX-TGP500 series Press and hold {ALL} for about 4 seconds until the STATUS indicator flashes in red. NKX-TGP550 series Press and hold {ALL} for about 4 seconds until the registration tone sounds and the STATUS indicator flashes in red. LIf all registered handsets start ringing, press the same button to stop. Then repeat this step. LThe next step must be completed within 90 seconds. 2 Handset: Press {OKL}, then wait until a long beep sounds.
Summary of the content on the page No. 5
Belt clip NTo attach NTo remove Wall mounting 1 Drive the screws (not supplied) into the wall. 2 Mount the charger (A), then slide it down (B) and to the right (C) until it is secure. 25.4 mm A (1 inch) B C Screws 5
Summary of the content on the page No. 6
For your safety To prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection L Completely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire. L Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated
Summary of the content on the page No. 7
L Charge the batteries provided with or identified for use with this product only, in accordance with the instructions and limitations specified in this manual. L Only use a compatible charger to charge the batteries. Do not tamper with the charger. Failure to follow these instructions may cause the batteries to swell or explode. Attention: A nickel metal hydride battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY (1-800-822- 8837) for information o
Summary of the content on the page No. 8
WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO EMERGENCY NUMBERS: 1) Remain on the line and briefly explain to the dispatcher the reason for the call. 2) Perform such activities in the off-peak hours, such as early morning or late evenings. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interferenc
Summary of the content on the page No. 9
Compliance with TIA-1083 standard: Compatible with Telephone handsets identified with this logo have reduced Hearing Aid T-Coil noise and interference when used with T-Coil equipped hearing aids and cochlear implants. T TIA-1083 Notice LThis product is designed for use in the United States of America. Sale or use of this product in other countries may violate local laws. LCet appareil est conçu pour être utilisé aux États-Unis d’Amérique. La vente ou l’emploi de cet appareil dans certains au
Summary of the content on the page No. 10
One Panasonic Way, Secaucus, New Jersey 07094 Copyright: This material is copyrighted by Panasonic System Networks Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic System Networks Co., Ltd. © Panasonic System Networks Co., Ltd. 2009 10