Summary of the content on the page No. 1
1
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
3
Summary of the content on the page No. 4
2. Installation 1. Locating the Base unit The Base unit should be placed on a level surface, in a position where: the mains adapter plug will reach an easily accessible 230-V AC switch mains supply socket - never try to lengthen the mains power cable. the telephone line cable will reach your telephone line socket or extension socket. it is not close to a sink, bath or shower, or anywhere else where it might get wet. it is not close to other electrical equipment - fridges, washing machines,
Summary of the content on the page No. 5
3. Desk/Wall mount installation Desk Mount To place the Caprice 600 on a desk, connect the stand to the bottom of the phone in the slots near the ringer cover as shown below. Insert the rigid clips of the stand into the slots on the bottom of the phone (near the ringer cover). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward (3) as shown below. Wall Mount To place the Capri
Summary of the content on the page No. 6
Desk/Wall mount installation continue... Insert the rigid clips of the stand into the slots on the bottom of the phone (near the battery cover). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward as shown below. Mark two points on the wall that are 137mm apart to lay the fixing centers as shown below. BE CAREFUL to check that there are no electrical wires hidden in the wall. F
Summary of the content on the page No. 7
4. Setting up the Caprice 600 The following section details how to set up your telephone. Press the MENU button to enter the Options menu and then use the UP or DOWN buttons to cycle through the following options: SET LANGUAGE SET TIME/DATE SET FLASH TIME LCD CONTRAST MESSAGE LENGTH RINGS TO ANSWER REMOTE ACCESS EXIT OPTION Note: The system will time out if you leave ! more than 15 seconds between key presses. SET With the phone in standby mode; LANGUAGE 1 Press MENU button. The displa
Summary of the content on the page No. 8
Setting up continue... 4 Press UP or DOWN button to set the year. 5 Press MENU button to confirm. The ‘month’ icon will be blinking. 6 Press UP or DOWN button to set the month. 7 Press MENU button to confirm. The ‘date’ icon will be blinking. 8 Press UP or DOWN button to set the date. 9 Press MENU button to confirm. The ‘hour’ icon will be blinking. 10 Press UP or DOWN button to set the hour. When setting the ‘hour’, the ‘AM’ or ‘PM’ icon will automatically turn ON to correspond the hour tim
Summary of the content on the page No. 9
Setting up continue... 5 Press MENU button to confirm. 6 Continue with programming, or press EXIT button to return to standby mode. 1 Press MENU button. LCD CONTRAST The display shows OPTIONS MENU OPTIONS MENU OPTIONS MENU OPTIONS MENU OPTIONS MENU . 2 Press UP or DOWN button until the display shows LCD CONTRAST LCD CONTRAST LCD CONTRAST LCD CONTRAST LCD CONTRAST. 3 Press MENU button to confirm. 4 Press UP or DOWN button to select your comfortable display viewing level
Summary of the content on the page No. 10
Setting up continue... To set the number of rings before the machine RINGS TO ANSWER answers a call; 1 Press MENU button. The display shows OPTIONS MENU OPTIONS MENU OPTIONS MENU OPTIONS MENU OPTIONS MENU . 2 Press UP or DOWN button until the display shows RINGS TO ANSWER RINGS TO ANSWER RINGS TO ANSWER RINGS TO ANSWER RINGS TO ANSWER. 3 Press MENU button to confirm. 4 Press UP or DOWN button to select TOLL SAVER, 2, 3, 4, 5, 6, 7, 8, or 9 rings. The default setting is
Summary of the content on the page No. 11
Setting up continue... 5 Press MENU button to confirm. The second digit of the code will be blinking. 6 Press UP or DOWN button to set the second digit of the REMOTE ACCESS code. 7 Press MENU button to confirm. The third digit of the code will be blinking. 8 Press UP or DOWN button to set the third digit of the REMOTE ACCESS code. 9 Press MENU button to confirm the REMOTE ACCESS setting. 10 Press EXIT button to return to standby mode. 5. Telephone Operation Ringer volume The Ringer High-Low s
Summary of the content on the page No. 12
Telephone operation continue... To answer a When the phone rings; call Lift the handset or press SPEAKERPHONE button on the Base unit. The display shows the duration of the call in minutes and seconds . To adjust the During a call; speakerphone Adjust the volume of the speakerphone to your volume comfortable volume level using the SPEAKERPHONE volume switch located at the right side of the Base unit. To end a call Replace the Handset on the Base unit cradle or press SPEAKERPHONE button on the B
Summary of the content on the page No. 13
6. Outgoing call record Last 1 Lift the handset or press SPEAKERPHONE Number button. redial 2 Press REDIAL/PAUSE button. The phone automatically redials the last number you called. Viewing the The telephone remembers the last 10 outgoing Outgoing call calls. records 1 In standby mode, press REDIAL/PAUSE button. The most recent outgoing call record will be displayed. 2 Press UP or DOWN button to view the other records. Making a 1 In standby mode, press REDIAL/PAUSE call from the button. Outgoi
Summary of the content on the page No. 14
Outgoing call record continue... Storing an 1 When viewing the Outgoing call records, press Outgoing UP or DOWN button to find the record you call record wish to store. into the 2 When the record is displayed, press BOOK Phonebook button. memory The display shows the cursor blinking on the first digit of the number. To modify the number, press UP or DOWN button to move the cursor to the number you want to change then input the new one or press ERASE button to delete. 3 Press BOOK button to con
Summary of the content on the page No. 15
Phonebook continue... name and the search will jump to the first entry in the Phonebook beginning with that letter. 5 Press UP or DOWN button to scroll through the other records. 6 Press EXIT button repeatedly to return to standby mode or wait until the program times out. To add a 1 Press BOOK button. new record The display shows SEARCH ADD SEARCH ADD SEARCH ADD, with the SEARCH ADD SEARCH ADD into the ‘SEARCH’ option blinking. Phonebook 2 Press UP or DOWN button to select ‘ADD ADD AD
Summary of the content on the page No. 16
Phonebook continue... 7 Press BOOK button to confirm. 8 Press EXIT button repeatedly to return to standby mode or wait until the program times out. To make a 1 When viewing the Phonebook records, press call from the UP or DOWN button to find the record you Phonebook wish to call. 2 Press DIAL button. The phone automatically dials the displayed record. The Caprice 600 dials the number using the speakerphone mode. Lift the Handset anytime to talk privately and to turn the speakerphone mode off.
Summary of the content on the page No. 17
Phonebook continue... To delete a 1 When viewing the Phonebook records, press record from UP or DOWN button to find the record you memory wish to edit. 2 When the record is displayed, press ERASE button. The display prompts DELETE? DELETE? DELETE? DELETE? DELETE? 3 Press ERASE button again to confirm. The display shows next Phonebook record. OR press EXIT button to cancel and return to the previous menu. 4 Press EXIT button repeatedly to return to the standby mode or wait until the program ti
Summary of the content on the page No. 18
Caller Display operation continue... The place origin of the Caller Display record will display a special network message as: Message Significant WITHHELD WITHHELD WITHHELD WITHHELD WITHHELD The caller hides his number. UNAVAILABLE UNAVAILABLE UNAVAILABLE UNAVAILABLE UNAVAILABLE The caller’s number is out of the network area. Withheld and Unavailable calls are not saved in the calls list and do not show as missed calls. Caller Display list This phone automatically stores the last 99 calls receiv
Summary of the content on the page No. 19
Caller Display operation continue... To return a When the Caller Display record is displayed; call from the Press DIAL button. Caller’s list The phone automatically dials the displayed record. Storing an 1 When viewing the Caller Display records, press Outgoing UP or DOWN button to find the record you call record wish to store. into the 2 When the record is displayed, press BOOK Phonebook button. memory The display shows the cursor blinking on the first digit of the number. To modify the numb
Summary of the content on the page No. 20
Caller Display operation continue... To delete When the Caller Display record is displayed. all Caller 1 Press and hold ERASE button. Display The display prompts DEL ALL CALLS? DEL ALL CALLS? DEL ALL CALLS? DEL ALL CALLS? DEL ALL CALLS? records 2 Press ERASE button to confirm. The display automatically returns to standby mode. OR press EXIT button to cancel and return to the previous menu. 9. Answering Machine system Outgoing An OGM is the announcement callers will hear when the machine answe
