Summary of the content on the page No. 1
1
User's Manual
for Tapeless Digital
Answering System Telephone
with Time/Day 1815
Fold open this manual for information
about this telephone's installation and
operation. Please read Part 1 —
Important Product Information,
included in this package.
Part 2
© 1998 Lucent Technologies Consumer Products L.P. All rights reserved.
Printed in Mexico. 848229571 Issue 2AT&T
Summary of the content on the page No. 2
INST ALLA TION Battery Installation (optional) RING SELECT POWER Telephone Line Cord 3 Connect the handset to the telephone. FOR TABLE/DESK INSTALLATION Plug the coiled cord into the handset jack on the side of the phone. Plug the other end of the coiled cord into the 1 Install the batteries (optional). handset, then hang up. • Turn the unit upside down. 4 Connect the line cord to a wall jack. • Push in on the two tabs at the large end of the base, and Plug the free end of the line cord into a
Summary of the content on the page No. 3
INST ALLA TION Reverse the Handset Tab 12 3 PULL TABS TO OPEN PULL TABS TO OPEN PULL TABS TO OPEN Figure 1 Figure 2 Figure 3 Figure 4 the tabs into the slots indicated. Push down on the large FOR WALL INSTALLATION end of the base to lock it into place (Figure 2). 6 Connect the line cord to the telephone. 1 Reverse the handset tab. Plug one end of the line cord into the jack labeled TEL (This tab holds the handset when you hang up.) Hold down LINE on the bottom of the phone (Figure 3). the swit
Summary of the content on the page No. 4
TELEPHONE OPERA TION Dial Mode Mute This phone comes set to operate with touch tone service. If you Mute lets you hear the other party, but prevents the other party have dial pulse (rotary) service, you will need to reset the dial from hearing you. mode. If you hear clicks (not tones) when you dial, you have dial pulse (rotary) service. To mute a call, press and release m. The MUTE light goes on. To change to dial pulse mode: 1 Press and release G. To return to two-way conversation, press a
Summary of the content on the page No. 5
TELEPHONE MEMOR Y Light is on when phone line is in use. When light goes on, battery needs to be replaced. Access telephone Store a pause in a subscriber services. memory dialing number. Put caller on Hold. (Light goes on when Dial numbers in call is on Hold.) telephone memory. Mute handset Store numbers in microphone. telephone memory. Redial last number called. Adjust listening volume Temporary Tone during a call. The telephone can store 9 telephone numbers, each up to 24 digits 3 Press and
Summary of the content on the page No. 6
ANSWERING SYSTEM OPERATION Select number of times line Set and hear rings before system answers Remote Access Code. (RING SELECT on back). Use with other buttons to change settings. Displays number of messages and other indicators. Set and hear time/day. Turn system on or off. Record and hear outgoing announcement. Repeat all or part of a message. Play messages. Stop message playback. Delete all or selected messages. Skip all or part of a message. Adjust listening volume during message playback.
Summary of the content on the page No. 7
ANSWERING SYSTEM OPERATION Repeat entire message — Press and release ?. Answering Calls Repeat part of message — Hold down ? for a When the system answers a call, the caller hears the announce- few seconds, then release it to resume playing. The ment you recorded, followed by a beep. After the beep, the system beeps while the button is held down. system begins recording your caller’s message. A caller can leave Skip to next message — Press and release /. a message up to 3 minutes long. If th
Summary of the content on the page No. 8
ANSWERING SYSTEM OPERATION You can change the Remote Access Code to any 3-digit number Recording a Memo from 500-999. You can record a memo to be stored as an incoming message. 1 Press and release g. The Message Window The memo can be up to 3 minutes long, and will be played back displays CH. with other messages. 2 Press and release c. The system announces “First 1 Press and release M. After the beep, speak digit.” toward the microphone. 3 Press / or ? to change the digit. 2 To stop recording
Summary of the content on the page No. 9
ANSWERING SYSTEM OPERATION From a Remote Touch Tone Phone Playing Messages Room Monitor with Intercom 1 Dial your telephone number from a touch tone phone. You can call the answering system and listen to any activity in the 2 When the system answers, enter your Remote Access room. Code. The system announces the number of messages 1 Press 9, 1 to listen for 30 seconds. received, then beeps twice. 2 If you wish, you can press 1 while the monitor is 3 After the two beeps, wait 4 seconds, and the s
Summary of the content on the page No. 10
IN CASE OF DIFFICUL TY If this answering system does not work properly, try the Messages Are Incomplete following suggestions. If you’re still having difficulty, call • The system can accept messages up to 3 minutes long. 1 800 222–3111. If a caller leaves a very long message, part of it might be lost when the system disconnects the call after No Dial Tone 3 minutes. • Make sure all plugs are connected properly. Check the • If the caller pauses for more than 7 seconds, the system line cord
Summary of the content on the page No. 11
fold fold a a a aaaaaaaaaaaaaaaaaaaaaaaaaaaa a a aaaaaaaaaaaaaaaaaaaaaaaaaaa Tapeless Digital Tapeless Digital Answering System 1815 Answering System 1815 2 2 Remote Commands Remote Commands Access Answering System Access Answering System 1 Dial your telephone number from a touch tone phone. 1 Dial your telephone number from a touch tone phone. 2 When the system answers, enter your Remote Access Code. 2 When the system answers, enter your Remote Access Code. The system announces the number of m
Summary of the content on the page No. 12
REMOTE COMMAND PRESS REMOTE COMMAND PRESS Play all messages 1 Play all messages 1 Play only new messages 2 Play only new messages 2 Repeat message 4 while message is playing Repeat message 4 while message is playing Skip message 6 while message is playing Skip message 6 while message is playing Delete all messages 3, 3 Delete all messages 3, 3 Delete selected message 3 while message is playing Delete selected message 3 while message is playing Record announcement 7, *, speak, press 5 to stop. Re
Summary of the content on the page No. 13
INS T ALL A TION INS T ALL A TION I N CAS E O F DIFFICU L TY If this answering system does not work properly, try the Messages Are Incomplete Reverse the Handset Tab Battery Installation (optional) following suggestions. If you’re still having difficulty, call • The system can accept messages up to 3 minutes long. 1 800 222–3111. If a caller leaves a very long message, part of it might be lost when the system disconnects the call after No Dial Tone 3 minutes. • Make sure all plugs are connect
Summary of the content on the page No. 14
TELEPHONE OPER A TION TELEPHON E MEMO R Y ANSWERING SYSTEM OPER ATION Select number of times line Dial Mode Mute Light is on when Set and hear rings before system answers phone line is in use. Remote Access Code. (RING SELECT on back). This phone comes set to operate with touch tone service. If you Mute lets you hear the other party, but prevents the other party have dial pulse (rotary) service, you will need to reset the dial from hearing you. When light goes on, mode. If you hear clicks (
