Summary of the content on the page No. 1
LPBG716A
LPBG724A
16-/24-Port Gigabit PoE PSE Web Smart Switch with 4 SFP Slots
Bring PoE into your Gigabit network.
Models available with sixteen or twenty-four autosensing,
auto-negotiating 10-/100-/1000-Mbps ports; four are dual-media
ports, which may be used for copper or fiber (SFPs).
Summary of the content on the page No. 2
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Caution Circuit devices are sensitive to static electricity, which can damage their delicate electronics. Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge. To protect your device, always: ∞Touch the metal chassis of your computer to ground the static electrical charge before you pick up the circuit device. ∞Pick up the device by holding it on the left and right e
Summary of the content on the page No. 3
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Federal Communications Commission and Industry Canada Radio Frequency Interference Statements This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with t
Summary of the content on the page No. 4
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Normas Oficiales Mexicanas (NOM) Electrical Safety Statement INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura. 3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas. 4. Todas las inst
Summary of the content on the page No. 5
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch European Community (CE) Electromagnetic Compatibility Directive This equipment has been tested and found to comply with the protection requirements of European Emission Standard EN55022/EN61000-3 and the Generic European Immunity Standard EN55024. EMC: EN55022 (2003)/CISPR-2 (2002): class A IEC61000-4-2 (2001): 4KV CD, 8KV AD IEC61000-4-3 (2002): 3V/m IEC61000-4-4 (2001):1KV (power line), 0.5KV (signal line)
Summary of the content on the page No. 6
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 1. Specifications 1.1 Hardware Specifications Certifications: FCC Class A, CE Flow Control: IEEE802.3x compliant for full duplex; Backpressure flow control for half duplex Full Forwarding/Filtering Packet Rate: PPS (packets per second) Forwarding Rate Speed 148,8000PPS 1000Mbps 148,800PPS 100Mbps 14,880PPS 10Mbps Standards Compliance: IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEE
Summary of the content on the page No. 7
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 1.2 Management Software Specifications Port Management: Port Configuration, Port Mirroring, Broadcast Strom Control, PoE On/ Off Setting VLAN Setting: Port-based/Tag-based, VLAN ID: 1–4094K Trunking: 2 groups (1–4 ports for each group) VLAN Function: Port-Base/802.1Q-Tagged, allowed up to 256 active VLANs in one switch QoS Setting: Up to 4 queues Security Filter: MAC address filtering RSTP: Rapid Spanning Tre
Summary of the content on the page No. 8
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 2. Overview 2.1 Features Supports the following: - - Real-time status (link, speed, duplex) of each port - - Port setting for enable or disable operation (the 1st port can’t be disabled) - - Pport setting for N-Way or force mode operation - - Broadcast Storm Protection - - Port-based VLAN - - Priority queues for QoS 2.2 What’s Included Your package should include the following items. If anything is mi
Summary of the content on the page No. 9
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Rear Panel AC Power Input Figure 2-3. LPBG716A or LPBG724A Rear Panel. 2.4 LED Indicators Figure 2-4. LED Indicators on the LPBG724A. LED Color Function System LED POWER Green Lit when power is on and good RESET Reset button is for management system restore 10/100/Gigabit Ethernet TP Port 1 to 24 LEDs Lit when connection with remote device is good LINK/ACT Green Blinks when any traffic is present Off
Summary of the content on the page No. 10
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 3. Installation 3.1 Hardware and Cable Installation CAUTION: Wear a grounding device to avoid damage from electrostatic discharge. Be sure that the power switch is OFF before you connect the power cord to the power source. 3.1.1 TP Port and Cable Installation 1. The switch’s TP ports support Auto-MDI/MDI-X crossover, so you can use straight-through (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 1, 2, 3, 6 in 10/10
Summary of the content on the page No. 11
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch SFP transceiver module Figure 3-1. 3.1.3 Power On The switch supports a 100–240 VAC, 50–60 Hz power supply. The power supply will automatically convert the local AC power source to DC power. It does not matter whether or not any connection is plugged into the switch when powering on. After the power is on, all LED indicators will light up and then all will turn off, except for the power LED, which stays on. 3.2 Install
Summary of the content on the page No. 12
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 3-2 Install the switch chassis in a 19"rack 3.3 Cabling Requirement For successful installation and good network performance, use CAT5, CAT5e, or higher cable. If you use non-compliant cables, the LAN will work poorly. For a Fast Ethernet TP network connection, the grade of the cable must be CAT5 or CAT5e with a maximum length of 328 feet (100 meters). 3.4 Switch Cascading in Topology Theoretically, the
Summary of the content on the page No. 13
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch The sum of all elements’ bit-time delay and the overall bit-time delay of wires/devices must be within the required Round Trip Delay (bit times) in a half-duplex network segment (collision domain). For full-duplex operation, this does not apply. 3.5 Set IP Address, Subnet Mask, and Default Gateway IP Address First, configure your PC IP address or change the IP address of the switch. Next, change the default gateway’s IP
Summary of the content on the page No. 14
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 3-5. Login Screen for Web. Page 14 724-746-5500 l www.blackbox.com
Summary of the content on the page No. 15
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4. Web-based Management Operation This chapter instructs you how to configure and manage the switch through the Web user interface it supports. You can access and monitor the switch’s status, including port activity, spanning tree status, port aggregation status, VLAN, and priority status and so on from any one port on the switch. The default values of the managed switch are listed in the table below: IP Address: 192.16
Summary of the content on the page No. 16
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.1 Web Management Home Overview After you login, you can select one of the configurations by clicking the icon in the configuration bar. There are four major categories for your configuration. - Configuration - - Monitoring - - Maintenance - - Logout 4.2 Configuration 4.2.1 System The System Configuration screen shows system status, including: MAC address, system firmware version, and so on. You can chan
Summary of the content on the page No. 17
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch 4.2.2 Ports You can enable or disable Jumbo Frames by clicking it in the check box. Select the “Port no.” that you want to configure for the mode below: - Auto speed - enable/disable the port - 10M/100M/1000M - full/half-duplex - enable/disable flow control Figure 4-3. Ports configuration. 4.2.3 VLANs There are 16 VLAN groups. Select and add a group into “VLAN ID” and then click the port number th
Summary of the content on the page No. 18
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 4-4. VLAN configuration. 4.2.4 Aggregation Set up port trunk groups and then click the port number you want to include in the same group. Choose from eight groups. The maximum for one group is 24 ports. Figure 4-5. Aggregation/ Trunk configuration. 4.2.5 LACP To enable/disable the protocol for a port, select the port number. Page 18 724-746-5500 l ww
Summary of the content on the page No. 19
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 4-6. LACP Port configuration. 4.2.6 RSTP To enable/disable the protocol for a port, select the port number. 724-746-5500 l www.blackbox.com Page 19
Summary of the content on the page No. 20
16/24 Port Gigabit PoE PSE With 4 SFP Slots Web Smart Switch Figure 4-7 RSTP configuration 4.2.7 802.1x Select the “Port no.” that you want to configure for the mode below: - Auto - Force Authorized - Force Unauthorized Figure 4-8. 802.1x configuration. Page 20 724-746-5500 l www.blackbox.com
