Summary of the content on the page No. 1
MULTI-TASKER
MANUAL PART NUMBER: 400-0176-002
MT104-107
3-IN, 1-OUT DUAL VIDEO/S-VIDEO
TM
SWITCHER CARD FOR MULTI-TASKER
USER’S GUIDE
Summary of the content on the page No. 2
MULTI-TASKER TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS .................. 2 1.1 GENERAL ................................ ..................... 2 1.2 INSTALLATION ................................ ............. 2 1.3 CLEANING ................................ .................... 2 1.4 FCC / CE NOTICE .............................
Summary of the content on the page No. 3
MULTI-TASKER These limits are designed to provide reasonable PRECAUTIONS / SAFETY WARNINGS 1 protection against harmful interference when the equipment is operated in a commercial Please read this manual carefully before using environment. This equipment generates, uses, your MT104 -107 . Keep this manual handy for and can radiate radio frequency energy and, if future reference. These safety instructions are to not installed and used in ac
Summary of the content on the page No. 4
MULTI-TASKER ABOUT YOUR MULTI-TASKER™ 2 MT104-107 MT10 4 The MT104 -107 is a dual 3 -IN 1 -OUT Video/S -Video Switc her Card. There are 3 inputs (+1internal) for Video and 3 inputs (+1internal) for MTBF (calc.) S -Video. It is desi gned for use in Multi -Tasker ™ Table 2. MT104-107 Mechanical enclosures. The MT Video/S -Video SW card ELECTRICAL MT104-107 enables composite video sources and S -Video Input Signals sources to be connected and
Summary of the content on the page No. 5
MULTI-TASKER PRODUCT DESCRIPTION 4 4
Summary of the content on the page No. 6
MULTI-TASKER APPLICATION DIAGRAM 5 5 Application 1
Summary of the content on the page No. 7
MULTI-TASKER MT104-107 3-IN 1-OUT VIDEO, S-VIDEO SWITCHER (BNC, 4-PIN DIN IN/OUT) INPUT POWER OFF S-Video OUTPUT Inputs 1 4-PIN 4-PIN MINI MINI 2 DIN DIN 3 INPUT OFF 1 C-Video OUTPUT Inputs BNC 2 BNC 3 INPUT SELECT CONTROL 6 Application 2: Internal View
Summary of the content on the page No. 8
MULTI-TASKER Commands not ending in "S" will still be INSTALLING YOUR MULTI-TASKER™ 6 executed, but will not be restored when the Step 1. Slide the MT104 -107 into an available system is Reset or powered OFF then ON. slot in the Multi-Tasker™ Enclosure in order to connect to the bus. Make sure that the MT104 -107 card fits into place. Each command consists of three parts: Secure the card to the Multi-Tasker™ by Function, card ID, and unit
Summary of the content on the page No. 9
MULTI-TASKER the command [VERC2U3] . T he Multi - Tasker™ [ -Video will return the following feedback: This command enables input “m” and disables all other inputs. MT104- 107 690-0160-002 [ ONm V CnUi]: Enables one composite video MT104-107 = card type input (C-Video) 690-0160-002 = software version [ ONm S CnUi]: Enables one S-Video input Default when plugged in: This command receives the status of the card. S-Video Input #1 = ON C-Vid
Summary of the content on the page No. 10
MULTI-TASKER S = saves command to memory card or a group of cards. Example: [ON1VG1U1] : Turns ON C-Video input 1 for -Video each card in group 1 of unit 1. This command disables input “m” or all inputs. …..P]: sets path : Turns OFF all C-Video inputs This command will set the path for the output, of the MT104-107 card. but it is not active until the switch command, m = Inpu t number (m = 1 to 4) [SW], is executed. Commands ending in "P"
Summary of the content on the page No. 11
MULTI-TASKER …..P]: sets path 8. […P] – Path This command will set the path for the output, This command will set the path for the output, but it is not active until the switch command, but it is not active until the switch command, [SW], is executed. Commands ending in "P" are [SW], is executed. Commands ending in "P" are not executed immediately. The path for outputs not executed immediately. The path for outputs on multiple cards or th
Summary of the content on the page No. 12
MULTI-TASKER Ui = unit number (i = # from 0-9) Example: Example: The cards in slots 1, 2 and 19 are part of group 5 in unit 1. Read the member data for group 5 To group cards #1, 2, and 3 as group 5 of unit of unit 1, by sending the command [RDG5U1] . #1, send the command [WRC1C2C3G5U1] . The system will return feedback as follows: After executing this command, cards 1, 2 and 3 will be grouped together as group 5 of unit 1. C1C2C19 G5U1 1
Summary of the content on the page No. 13
MULTI-TASKER 8) Sets the path, preload for 8.2 NO DISPLAY 9) Cause 1 The source has a problem. 10) Display available commands Solution: Check the source and make sure that there is a signal present and all 11) source connections are correct. If 12) Clears members of a single group the source is working and there is still no display, see Cause 2. Cause 2: The card input i s not selected. 13) Requests group data Solution: Select the card in
