Summary of the content on the page No. 1
AT-S95 Version 2.0.0.24
AT-8000GS Switch
Software Release Notes
Please read this document before you begin to use the management software.
The following topics are included in this document
“Supported Platforms” on page 1
“Upgrade Procedure” on page 2
“Product Documentation” on page 6
“Newly Introduced Feature” on page 6
“Resolved Issues” on page 6
“Known Issues” on page 6
“Where to Find Product Information and Management Software Updates” on page 7
“Contacting Allied Telesis” on page
Summary of the content on the page No. 2
AT-S95 Version 2.0.0.24 Software Release Notes Upgrade Procedure This section describes how to upgrade the AT-S95 bootloader and software to the latest version using both the CLI and web interfaces. See the following subsections: “Upgrading the AT-S95 Bootloader Code and Software with the CLI” on page 2 “Upgrading the AT-S95 Bootloader and Software with the Web Browser Interface” on page 3 Allied Telesis strongly recommends that you upgrade your switch’s boot loader to the latest version, ve
Summary of the content on the page No. 3
AT-S95 Version 2.0.0.24 Software Release Notes 6. Reboot the device with the following command: console# reload This command causes the switch to reboot. By the end of the reboot process, the final code drop will be running. Note To upgrade stacked AT-8000GS switches, see the AT-S95 Management Software CLI User’s Guide for instructions. Upgrading the AT-S95 Bootloader and Software with the Web Browser Interface To upgrade the AT-S95 bootloader and management software to the latest version with
Summary of the content on the page No. 4
AT-S95 Version 2.0.0.24 Software Release Notes Figure 2. File System Tab 3. Select the type of TFTP operation to perform. Click both of the following: Download Firmware 4. In the Source File Name field, type the bootloader filename: ati8000gs_boot-2001.rfb 5. From the pull down menu under the Destination File heading, select Bootfile. 6. Enter the IP address of the TFTP server in the TFTP Server IP Address heading. 7. Click Apply. The Copy Finished Popup window is displayed. See Figure 3. Figu
Summary of the content on the page No. 5
AT-S95 Version 2.0.0.24 Software Release Notes 8. Click OK. 9. In the Source File Name field, type the filename of the AT-S95 image: ati8000gs_bx-20024.ros 10. From the pull down menu under the Destination File field, select Software Image. 11. Click Apply. The Copy Finished popup window is displayed. See Figure 3 on page 4. 12. Click OK. 13. Select the System Utilities tab. See Figure 4. Figure 4. System Utilities Tab after Image 2 has been Loaded 14. In the After Reset column, select Image 2 f
Summary of the content on the page No. 6
AT-S95 Version 2.0.0.24 Software Release Notes 17. Click the Reset button. The switch is rebooted. Product Documentation For hardware installation instructions for the AT-8000GS switches, refer to the following manual: AT-8000GS Series Stackable Gigabit Ethernet Switches Installation Guide For software management instructions, refer to the following manuals: AT-S95 Management Software CLI User’s Guide AT-S95 Management Software Web Browser Interface User’s Guide These documents are available
Summary of the content on the page No. 7
AT-S95 Version 2.0.0.24 Software Release Notes Stack: Master and backup are 24 ports non PoE, slave unit 3 is 48 ports. When reloading unit 2 the master reboots rarely. DHCP Option 82: the device doesn’t recognize option 82 fields that refer to the device itself (to the internal interface). Instead of getting an IP address, the device removes the option 82 field (which is actually correct) and then it transmits the traffic to the trusted ports. MAC Support: Max 1K MAC Addresses can be conf
Summary of the content on the page No. 8
AT-S95 Version 2.0.0.24 Software Release Notes IGMP Snooping— The no free timer issue with the IGMPSNOOPP_timer_create command has been resolved (CQ 121102). Web— The AT-8000GS/24 web interface fiber port link indicator has been fixed (CQ 122342). Online Help— Issue with the device help has been resolved (CQ 119900). SW2M: ABORT DATA exception has been resolved (CQ 122564). History of Newly Introduced Features The Dot1x Legacy Compliant feature is advanced 802.1x configuration enabling suppo
Summary of the content on the page No. 9
AT-S95 Version 2.0.0.24 Software Release Notes Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales and corporate information. Online Support You can request technical support online by accessing the Allied Telesis Knowledge Base: www.alliedtelesis.com/support. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions. Email and Telephone Support For T
