Summary of the content on the page No. 1
IES-5000/5005/6000
Integrated Ethernet Switch
Support Notes
July 2008
Edition 3
Summary of the content on the page No. 2
IES-5000/5005/6000 Support Notes INDEX Application Notes............................................................................................................................ 2 Triple play Application (with VLC Line Card).............................................................. 2 Triple play Application (with ALC/SLC Line Card) .................................................... 29 VDSL2 to ADSL2+ Fallback....................................................................
Summary of the content on the page No. 3
IES-5000/5005/6000 Support Notes Application Notes Triple play Application (with VLC Line Card) The triple play service is a marketing term for the provisioning of two broadband services, high-speed Internet access and television, and one narrowband service, telephone, over a single broadband connection. Triple Play focuses on a combined business model rather than solving technical issues or a common standard. Triple Play ZyXEL provides Triple Play solutions to implement t
Summary of the content on the page No. 4
IES-5000/5005/6000 Support Notes Triple Play scenario topology 3 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 5
IES-5000/5005/6000 Support Notes Hardware connections: P-870H-51 1. DSL: Connect the DSL jack to the VLC1348G-51 card on IES-5000. 2. Ethernet: Connect the clients to the Ethernet jacks: (1).IP Phone to the Ethernet 1 (2).IP STB to the Ethernet 2 (3).PC to the Ethernet 3 IES-5000M (Main Chassis) 1. Install the MSC1000G in SLOT1. 2. Install the VLC1348G-51 in SLOT3. MSC1000G Connect the UP1 port of the MSC1000G to the Port12 of the ES-2024A. VLC1348G-51 1. U
Summary of the content on the page No. 6
IES-5000/5005/6000 Support Notes Firmware versions: ES-2024A V3.80(TX.0)C0 IES-5000 MSC1000G: V3.90(LU.1)C0 VLC1348G-51: V3.90(BHB.0)b1 P-870H-51 1.00(AWG.6)G0 5 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 7
IES-5000/5005/6000 Support Notes Configure the P-870H-51: In this scenario, we will use the CPE P-870H-51 with factory-default setting. How to set the P-870H-51 to factory-default? Press the RESET button on the back-end plane of the housing (you can see it in the following picture). Keep it pressed down for several seconds, until you see that the POWER LED is blinking, which means the factory default setting is being applied to the device. 6 All contents copyright (c) 2008 Z
Summary of the content on the page No. 8
IES-5000/5005/6000 Support Notes Configure the IES-5000 1. System login. a. Connect to the IES-5000 via Internet browser. 192.168.1.1 is the default in-band management IP address and 192.168.0.1 is the default out-of-band (management port) IP address. Enter the default username (“admin”) and the password (“1234”) to access the device: b. The main screen appears after clicking OK. 7 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 9
IES-5000/5005/6000 Support Notes 2. Configure the VLC1348G-51. a. Click Port > VDSL. b. Choose slot 3 and port 1, and click Load to open the page shown below: c. Select the Enable check-box to enable the VDSL port1, click Apply to save the settings. 8 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 10
IES-5000/5005/6000 Support Notes d. Click the Setup button in sub-step (1) of the VLAN to open the page relevant for sub-step (2) & (3): Sub-step (1): Open VLAN setup page. Sub-step (2): Join VLAN 100 to VDSL port 1. 9 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 11
IES-5000/5005/6000 Support Notes Sub-step (3): Join VLAN 500 to VDSL port 1. Sub-step (4): Check the final VLAN setup status, you should see two entries as below. 10 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 12
IES-5000/5005/6000 Support Notes Sub-step (5): Set the default PVID/Priority for the VDSL Port1, click Apply to save the changes. 11 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 13
IES-5000/5005/6000 Support Notes 3. Configure the MSC1000G. a. Click VLAN > VLAN b. Select VLAN 100 and click Modify, then set the port UP1 as Fix and Tag, then click Apply to save the changes: 2 1 c. Select VLAN 500 and click Modify, then set the port UP1 as Fix and Tag, then click Apply to save the changes: 2 1 12 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 14
IES-5000/5005/6000 Support Notes d. Check the final VLAN setup status of the MSC1000G 13 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 15
IES-5000/5005/6000 Support Notes 4. Use ACL rule to replace the VID / Priority for the PPPoE packets. [Note]: So far ACL-rule feature does not support WEB-GUI, we use the CLI method to configure it. a. Login: Connect your PC to the out-of-band MGMT port of MSC1000G, and call the Windows MS-DOS, then use Telnet method to login (use the default management IP: 192.168.0.1). After issuing the default ‘admin’ / ’1234’ to login, you can see the page shown below: 14 All conten
Summary of the content on the page No. 16
IES-5000/5005/6000 Support Notes b. ACL-rule profile CLI syntax: (1). is for picking out the traffic by specific parameters, e.g. the vid (802.1q), mac, etype (Ethernet Type), priority (802.1p) etc. (2). can apply actions to the traffics picked out by the , e.g. rate (limit the rate), rvlan (replace vlan), rpri (replace priority) 15 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 17
IES-5000/5005/6000 Support Notes c. Set ACL-rules to pick out PPPoE traffic and replace its VID / Priority. (1) Create ACL profiles // ‘pppoe1’ & ‘pppoe2’ are the Profile names, and ‘34915’ is the decimal value for hexadecimal value 0x8863, and ‘34916’ is for 0x8864.// (2) Apply the ACL profile to the VDSL port 3-1 // “3-1” represents the slot 3 and port 1, which is exactly the VDSL port we are using.// Based on the above settings, all the PPPoE traffics including the Ethe
Summary of the content on the page No. 18
IES-5000/5005/6000 Support Notes 5. Use MVR to configure the IPTV setting on MSC1000G. a. Login: As in the step 4, use Telnet to login. b. Set VDSL port 3-1 to join the MVR VLAN 700. c. Set multicast group range for MVR VLAN 700 //Since we are using 239.255.255.2 as the multicast group IP in this case, we set the group range starting from 224.1.1.1 to 239.255.255.255// d. Enable MVR VLAN 700 17 All contents copyright (c) 2008 ZyXEL Communications Corporation.
Summary of the content on the page No. 19
IES-5000/5005/6000 Support Notes 6. Configure the IGMP-Proxy and Static Query VLAN a. Login: We are using the WEB to configure again. b. Click Multicast, then Enable IGMP Proxy V2 mode, and click Apply to save the changes. c. Add Static Query VLAN 500, and click Apply to save the changes. [Note:] As we don’t have any IGMP-router in this scenario, Static Query VLAN should be assigned to specify the multicast service subscriber VLANs. // And because all the traffics sending
Summary of the content on the page No. 20
IES-5000/5005/6000 Support Notes d. Check the Query VLAN status. 19 All contents copyright (c) 2008 ZyXEL Communications Corporation.
