Summary of the content on the page No. 1
INSTALLATION INSTRUCTIONS
HD88CC5 HD88C
High Definition Video Matrix Switcher, High Definition Video Matrix Switcher,
Coaxial and CAT5 Coaxial Only
DESCRIPTION
The HD88CC5 eight-source, eight-zone, high-definition matrix switcher allows Hi-Definition Video and
digital Audio signals to be sent over standard Coax cable or CAT5 cable with virtually no loss. Both
coaxial component and CAT5 video outputs are active simultaneously, making it possible to distribute
eight sources to s
Summary of the content on the page No. 2
Safety Information CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation p
Summary of the content on the page No. 3
Damage Requiring Service — These appliances should be serviced by qualified service personnel when: • A power supply connection or a plug has been damaged or • If liquid has been spilled into the appliance or objects have fallen into the appliance or • The appliance has been exposed to water or moisture or • The appliance does not appear to operate normally or exhibits a marked change in performance or • The appliance has been dropped or the enclosure damaged. Replacement Parts — When
Summary of the content on the page No. 4
IMPORTANT NOTICE HD44 Series and HD88 Series INTRODUCTION In some installation scenarios, an audio/video source component (such as a cable box or DVD player) may fail to work properly with distribution products or even a display. The problem is often related to the source component’s video outputs exhibiting too much DC offset voltage on the signal line. The result of poor DC offset voltage conditioning on the output often results in color problems such as color bleeding, pictur
Summary of the content on the page No. 5
DETAIL OVERVIEW FRONT PANEL The front panel is designed to provide the unit’s current Output/Input setting status. Note that only one Output/Input status setting is displayed at any given moment. The top row of LED indicators represents the current ZONE output selection. The bottom row of LED indicators represents the current SOURCE input selection. The LED columns are numbered 1 to 8, from left to right. To review the Zone/Input assignment, you must first perform a Zone
Summary of the content on the page No. 6
REAR PANEL [1] SOURCE LOOP-THROUGH CONNECTION The source inputs are buffered to provide an output at the same level as the input – i.e. Unity Gain (assuming a 75-ohm termination is on the output). Use these connections for HD88 expansion systems. The buffers are an active circuit. The HD88 must be powered on for an active connection. The jacks are color-coordinated to match the HD source component output color scheme. [2] SOURCE INPUTS These are Gold-plated RCA jacks providin
Summary of the content on the page No. 7
[4] RS232 (SERIAL) COMMANDS The RS232 Port is bi-directional. The communication parameters are set to 9600 Baud 8-N-1. DB9 CONNECTOR CIRCUIT PIN TX 2 RX 3 GND 5 RS232 COMMAND STRUCTURE Where: {z#} - Zone Number. Range is 1..4 (1..16 if expanded) {s#} - Source Input Number. Range is 1..4 {0/1} – Either 0 (zero) or 1 (one). 0 – Off, 1 – On. REMARKS NAME COMMAND Zone Power !{z#}PR{0/1}+ To turn on Zone 2: !2PR1+ To turn off Zone 1: !1PR0+ Zone Power Toggle !{z#}
Summary of the content on the page No. 8
[5] RS232 EXPANSION The HD88C and HD88CC5 can be expanded into larger systems. By using any combination of the HD88C and HD88CC5 (up to 4 units), a larger High-Definition distribution system can be created for up to 32 Zones of Component Video and Digital Audio Distribution. The expanded HD88C units must have their own unique address (see ADDRESS (DIP SWITCH) section). The included RS232 expansion cable allows the units to be daisy chained via the RS232 control ports. This is done by
Summary of the content on the page No. 9
[7] IR BUS The IR_IN port utilizes a 3.5mm mono jack. Use this port to connect to an IR emitter output port of a Xantech connecting block. PLUG CIRCUIT TIP IR SIGNAL SLEEVE GROUND [8] CAT5 ZONE OUTPUT This is an Output connection to the HDRXSG01 receiver module. It utilizes standard CAT5 cable. Be sure to verify CAT5 wiring connection is correct before installation. [9] COAXIAL ZONE OUTPUT These Gold-plated RCA jacks provide for a connection to HD monitors. The jacks have bee
Summary of the content on the page No. 10
QUICK INSTALLATION: HD88CC5 and HDRXSG01 [1] Connect the High-Definition Source to the HD88CC5 or HDTXSG01. Figure 1 below shows an HD88CC5 (video matrix transmitter) connected to the HDRXSG01 (receiver). [2] Using CAT5 cable, connect the HD88CC5 zone output or the output from the HDTXSG01 to the HDRXSG01. Connect power to the HD88CC5 first, then connect power to the HDRXSG01. [3] On the HD88CC5, make the desired Zone/Source assignment. See HD88CC5 manual on how to use RS232 and IR
Summary of the content on the page No. 11
RC68+ (IR) COMMANDS The RC68+ should be set to Group Code “F1”. ZONE 1 2 3 4 5 6 7 8 1 Zone Selection 80 48 10 90 00 C0 50 D0 2 Source Selection 40 A0 30 B0 20 E0 70 F0 3 Zone Power On 60 88 18 98 08 A8 38 B8 4 Zone Power Off 28 E8 78 F8 68 C8 58 D8 5 Zone Power Toggle E1 89 C9 A9 71 19 59 39 6 Zone All On F1 7 Zone All Off 99 8 Save Preset D9 9 Clear Preset B9 10 Preset One 01 11 Preset Two 41 12 Preset Three 21 13 Preset Four 61 14 Restore All Zones F9
Summary of the content on the page No. 12
ADVANCE INSTALLATION Sports Bar The figure below shows a diagram for a sports bar application. With the equipment rack located near or behind the bar area, the coaxial outputs can be used for local HD monitors. The CAT5 outputs can be used to deliver HD content to areas such as outdoor patios and pool table recreational areas. FIGURE 2 08905150B - 12 -
Summary of the content on the page No. 13
Expanded System The figure below shows an expanded HD88CC5 (16 Zones and up to 32 HD monitors) system. With two HD88CC5 devices, HD content can be distributed to 32 displays (16 with CAT5 outputs, 16 with coaxial outputs). The included RS232 expansion cable allows a single RS232 control port to be used to command the entire system. Expansion specific communications between units is accomplished via the Expansion Cable. FIGURE 3 08905150B - 13 -
Summary of the content on the page No. 14
Notes: 08905150B - 14 -
Summary of the content on the page No. 15
Xantech Limited Warranty (Effective for products sold after July 1, 2006) Xantech Corporation (“Xantech”) warrants to the holder of a valid proof of purchase as the first end-user purchaser (“You”), its products to be free from defects in materials and workmanship for the periods specified below from the date of purchase. This limited warranty extends only to You for product purchased and used in the United States of America. For product purchased outside of the United States of Ameri
Summary of the content on the page No. 16
Xantech Corporation 13100 Telfair Avenue Sylmar, CA 91342 www.xantech.com Phone: (818) 362-0353, Fax: (818) 362-9506 Installation Instructions, HD88CC5, HD88C © 2009 Xantech Corporation This document is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from Xantech Corporation. Xantech Corporation shall not be liable for operational, technical, or editorial erro
