Summary of the content on the page No. 1
Enterprise Networking Solution
User Guide
Gigabit Uplink Web Smart Switch
TL-SL2210WEB/TL-SL2218WEB
TL-SL2428WEB/TL-SL2452WEB
Summary of the content on the page No. 2
Summary of the content on the page No. 3
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. ht
Summary of the content on the page No. 4
Related Document This User Guide is also available in PDF on our website. To obtain the latest product information, please visit the official website: http://www.tp-link.com About this User Guide This User Guide describes the hardware characteristics, installation methods and the points that should be attended to during installation. This User Guide is structured as follows: Chapter 1 Introduction. This chapter describes the external components of the Switch. Chapter 2 Installation. This
Summary of the content on the page No. 5
Audience This User Guide is for: Network Engineer Network Administrator Conventions Due to the similarity in structure of TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/ TL-SL2452WEB Gigabit Uplink Web Smart Switch series, in this User Guide we take TL-SL2210WEB as an example to illustrate Chapter 2 Installation, Chapter 3 Lightning Protection, Chapter 4 Connection and Chapter 6 WEB Management. This Guide uses the specific formats to highlight special messages. The following table lists the noti
Summary of the content on the page No. 6
Contents Chapter 1 Introduction ——————————————— 01 1.1 Product Overview ............................................................................................ 01 1.2 Features ............................................................................................................... 01 1.3 Appearance ........................................................................................................ 02 Chapter 2 Installation ———————————————— 05 2.1 Package Contents .................
Summary of the content on the page No. 7
5.3.5 Dynamic Binding ...................................................................................... 18 5.3.6 Ping ............................................................................................................... 19 5.4 VLAN Setting ..................................................................................................... 19 5.4.1 VLAN Mode ................................................................................................ 19 5.5 Port Trunking ......
Summary of the content on the page No. 8
Gigabit Uplink Web Smart Switch ChaCter C Introduction C1C Product Overview The TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Gigabit Uplink Web Smart Switch is compliant with the IEEE802.3 Ethernet protocols. The EIA-standardized framework and smart configuration capacity can provide flexible solutions for variable scale of networks. This switch family is equipped with powerful management interface, via which system, port, network, VLAN, truck and priority can be configured. The TL-
Summary of the content on the page No. 9
Gigabit Uplink Web Smart Switch C11 ACCearance ■ Front Panel The front panel of TL-SL2210WEB is shown as the following figure. R TL-SL2210WEB 8+2GWeb-SmartSwitch 12345678 GIGA SFP Power Link Link/Act Act 12345678 System 100M 1000M Link/Act GIGA RESET 10/100Mbps 10/100/1000Mbps 1000Mbps LEDs RESET 10/100Mbps RJ45 Port 10/100/1000Mbps RJ45 Port SFP Port Figure 1-1 Front Panel of TL-SL2210WEB The front panel of TL-SL2218WEB is shown as the following figure. 135 7 9 11 13 15 R Link 135
Summary of the content on the page No. 10
Gigabit Uplink Web Smart Switch RESET Press this button for three seconds to reset the software setting back to factory default setting. LEDs LED Status Indication On The Switch is powered on Power Off The Switch is powered off or power supply is abnormal On The Switch works properly System Off The Switch works improperly A valid link is established on the port On Data is being transmitted or received. (SFP port has Link/ Flashing Link/Act Act LED only and must connect to 1000Mbps devi
Summary of the content on the page No. 11
Gigabit Uplink Web Smart Switch ■ Rear Panel The rear panel of TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB is shown as the following figure. Power Socket Figure 1-5 Rear Panel Power Socket Connect the female connector of the power cord here, and the male connector to the AC power outlet. Please make sure the voltage of the power supply meets the requirement of the input voltage. Caution: Please use the provided power cord. Introduction 04
Summary of the content on the page No. 12
R TL-SL2210WEB 8+2GWeb-SmartSwitch 1234 56 78 GIGA SFP Power Link Link/Act Act12345678 System 100M 1000M Link/Act GIGA RESET 10/100Mbps 10/100/1000Mbps 1000Mbps Gigabit Uplink Web Smart Switch ChaCter 1 Installation 11C Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Gigabit Uplink Web Smart One AC Power Cord Switch This User Guide Two Mounting Brackets and the Fittings 111 Safety P
Summary of the content on the page No. 13
Gigabit Uplink Web Smart Switch ■ Site Requirements To ensure normal eperation and long service life of the device, please install it in an environment that meets the requirements described in the following subsection. Temperature/Humidity R TL-SL2210WEB 8+2GWeb-SmartSwitch 12345678 GIGA SFP Power Link Link/Act Act 12345678 System 100M 1000M Link/Act GIGA RESET 10/100Mbps 10/100/1000Mbps 1000Mbps Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may
Summary of the content on the page No. 14
Gigabit Uplink Web Smart Switch ■ Keep the device far from high-frequency, strong-current devices, such as radio transmitting station. ■ Use electromagnetic shielding when necessary. Lightening Protection R TL-SL2210WEB 8+2GWeb-SmartSwitch 12345678 GIGA SFP Power LAc intk Link/Act 12345678 System 100M 1000M Link/Act GIGA RESET 10/100Mbps 10/100/1000Mbps 1000Mbps Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be i
Summary of the content on the page No. 15
Gigabit Uplink Web Smart Switch 111 Installation Tools ■ Phillips screwdriver ■ ESD-preventive wrist wrap ■ Cables Note: These tools are not provided with our product. If needed, please self purchase them. 112 Product Installation ■ Desktop Installation To install the device on the desktop, please follow the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. Remove the adhesive backing papers from the rubber feet. 3. Tu
Summary of the content on the page No. 16
R TL-SL2210WEB 8+2GWeb-SmartSwitch 1234 56 78 GIGASFP Power Link Link/Act Act 1234 5678 System 100M 1000M Link/Act GIGA RESET 10/100Mbps 10/100/1000Mbps 1000Mbps R TL-SL2210WEB 8+2GWeb-SmartSwitch 57 IAS P 12 3468 G G F Power Link Link/Act Act 1 234 5 6 7 8 System 100M 1000M Link/Act GIGA RESET 10/100Mbps 10/100/1000Mbps 1000Mbps Gigabit Uplink Web Smart Switch Rack-mounting Bracket Screw Figure 2-2 Bracket Installation 3. After the brackets are attached to the device, use suitable screws (not p
Summary of the content on the page No. 17
Gigabit Uplink Web Smart Switch ChaCter 1 Lightning Protection 11C Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors, please use a signal lightning arrester. ■ Requirements for Cabling Outdoors ■ Aerial cabling wit
Summary of the content on the page No. 18
Gigabit Uplink Web Smart Switch ■ Requirements for Cabling Indoors When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. ■ The main cable should be paved in the metal raceway of the access shaft. When cabling, keep the loop area formed by the cable itself as small as possible. ■ Requirements for the distance between Ethernet cable and other pipelines are
Summary of the content on the page No. 19
Gigabit Uplink Web Smart Switch Parallel cabling 300 2~5kVA One is in the grounded metal raceway or metal pipe 150 powerline The both are in the grounded metal raceway or metal pipe 80 Parallel cabling 600 >5kVA One is in the grounded metal raceway or metal pipe 300 powerline The both are in the grounded metal raceway or metal pipe 150 Device Min Distance (m1 Switch case 1.00 Transformer room 2.00 Elevator tower 2.00 Air-conditioner room 2.00 111 Connect to Ground Connecting the device to gro
Summary of the content on the page No. 20
TL-SL2210WEB 8+2GWeb-S 1 Link/Act 6 7 8 1000M GIGA RESET R TL-SL2210WEB 8+2GWeb-SmartSwitch 1 2 3 4 5 6 7 8 GIGA SFP Power Link Link/Act Act 1 2 3 4 5 6 7 8 System 100M 1000M Link/Act GIGA RESET 10/100Mbps 10/100/1000Mbps 1000Mbps 8GIGASFP Link/Act 10/100/1000Mbps 1000Mbps R TL-SL2210WEB 8+2GWeb-SmartSwitch 1 2 3 4 5 6 7 8 GIGA SFP Power Link Link/Act Act 1234 5678 System 100M 1000M Link/Act GIGA RESET 10/100Mbps 10/100/1000Mbps 1000Mbps Gigabit Uplink Web Smart Switch ChaCter 2 Connection 21C E
