Summary of the content on the page No. 1
Enterprise Networking Solution
Installation Guide
Gigabit Smart Switch
TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452
Summary of the content on the page No. 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. ht
Summary of the content on the page No. 3
Related Document The User Guide and CLI Reference Guide (CLI Reference Guide is not available for TL-SG24521 of the product are provided on the resource CD. To obtain the latest product information, please visit the official website: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during installation. This Installation Guide is structured as follows: Chapte
Summary of the content on the page No. 4
Contents Chapter 1 Introduction ———————————— 01 1.1 Product Overview .....................................01 1.2 Appearance ...................................................01 Chapter 2 Installation ———————————— 07 2.1 Package Contents .....................................07 2.2 Safety Precautions ....................................07 2.3 Installation Tools ......................................09 2.4 Product Installation ..................................10 Chapter 3 Lightning Protection ———
Summary of the content on the page No. 5
Gigabit Smart Switch ChaCter C Introduction C1C Product Overview TP-LINK Gigabit Smart Switch, designed for workgroups and departments, provides wire-speed performance and abundant layer 2 management features. It provides a variety of service features and multiple powerful functions with high security. The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks. QoS and IGMP snooping/filtering optimize voice and video appli
Summary of the content on the page No. 6
Gigabit Smart Switch The front panel of TL-SG2424 is shown as the following figure. Reset LEDs 10/100/1000Mbps RJ45 Port SFP Port Figure 1-2 Front Panel of TL-SG2424 Reset Press this button for five seconds or above to reset the software setting back to factory default settings. LEDs LED Status Indication On The Switch is powered on Power Off The Switch is powered off or power supply is abnormal On The Switch is working abnormally System Flashing The Switch is working normally Off The Switch is
Summary of the content on the page No. 7
Gigabit Smart Switch The front panel of TL-SG2424P is shown as the following figure. LEDs LED Mode Switch Button Reset 10/100/1000Mbps RJ45 Port SFP Port Figure 1-3 Front Panel of TL-SG2424P LEDs TL-SG2424P has an LED mode switch button which is for switching the LED status indication. When the Speed LED is on, the port LED is indicating the data transmission rate. When the PoE LED is on, the port LED is indicating the power supply status. By default the Speed LED is on. Pressing the mode swi
Summary of the content on the page No. 8
Gigabit Smart Switch LED Status Indication On The remaining PoE power ≤7W The remaining PoE power keeps ≤ 7W after this LED is PoE Max Flashing on for 2 minutes Off The remaining PoE power ≥7W On The port is supplying power normally Green The supply power exceeds the correponding port's Flashing 10/100/ maximum power 1000Mbps On Overload or short circuit is detected Yellow Flashing Power-on self-test has failed Off No PoE power supply is provided on the port LED Mode Switch Button Press this
Summary of the content on the page No. 9
Gigabit Smart Switch LED Status Indication A 1000Mbps device is connected to the corresponding On port, but no activity Green Flashing Data is being transmitted or received 10/100/ 1000Mbps A 10/100Mbps device is connected to the corresponding On port, but no activity Yellow Flashing Data is being transmitted or received Off No device is connected to the corresponding port 10/100/1000Mbps RJ45 Port Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a c
Summary of the content on the page No. 10
Gigabit Smart Switch The rear panel of TL-SG2424 is shown as the following figure. Grounding Terminal Power Socket Figure 1-6 Rear Panel of TL-SG2424 The rear panel of TL-SG2424P is shown as the following figure. Grounding Terminal Power Socket Figure 1-7 Rear Panel of TL-SG2424P The rear panel of TL-SG2452 is shown as the following figure. Grounding Terminal Power Socket Figure 1-8 Rear Panel of TL-SG2452 Grounding Terminal The Switch already comes with lightning protection mechanism. Y
Summary of the content on the page No. 11
Gigabit Smart Switch ChaCter 1 Installation 11C Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. This Installation Guide One Switch One Power Cord Two mounting brackets and the One Resource CD fittings 11 1 Safety Precautions To avoid any device damage and bodily injury caused by improper use, please observe the following rules. ■ Safety Precautions ■ Keep the power off during the ins
Summary of the content on the page No. 12
Gigabit Smart Switch ■ Site Requirements Temperature/Humidity Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table. Environment Temperature H
Summary of the content on the page No. 13
Gigabit Smart Switch Lightning Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. ■ Ensure the rack and device are well earthed. ■ Make sure the power socket has a good contact with the ground. ■ Keep a reasonable cabling system and avoid
Summary of the content on the page No. 14
Gigabit Smart Switch 112 Product Installation ■ Desktop Installation To install the device on the desktop, please follow the steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. Remove the adhesive backing papers from the rubber feet. 3. Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device. Feet Bottom of the Device Notch Figure 2-1 Desktop Installation ■ R
Summary of the content on the page No. 15
Gigabit Smart Switch Rack Figure 2-3 Rack Installation Caution: ■ Please set 5~10cm gaps around the device for air circulation. ■ Please avoid any heavy thing placed on the device. ■ Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation. Installation 11
Summary of the content on the page No. 16
Gigabit Smart Switch ChaCter 2 Lightning Protection 21C Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors, please use a signal lightning arrester. ■ Requirements for Cabling Outdoors ■ Aerial cabling without safegua
Summary of the content on the page No. 17
Gigabit Smart Switch ■ Requirements for Cabling Indoors When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. ■ The main cable should be paved in the metal raceway of the access shaft. When cabling, keep the loop area formed by the cable itself as small as possible. ■ Requirements for the distance between Ethernet cable and other pipelines are shown in th
Summary of the content on the page No. 18
Gigabit Smart Switch Min Parallel Cable Pave Way Length (mm1 Parallel cabling 300 2~5kVA One is in the grounded metal raceway or metal pipe 150 powerline The both are in the grounded metal raceway or metal 80 pipe Parallel cabling 600 >5kVA One is in the grounded metal raceway or metal pipe 300 powerline The both are in the grounded metal raceway or metal 150 pipe Device Min Distance (m1 Switch case 1.00 Transformer room 2.00 Elevator tower 2.00 Air-conditioner room 2.00 211 Connect to Ground
Summary of the content on the page No. 19
Gigabit Smart Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. ■ Connecting to the Ground via the Power Supply If the device is installed in the normal environment, the device can be grounded via the PE (Protecting Earth1 cable of the AC power supply as shown in the following figure. Figure 3-2 Connecting to the Ground Note: ■ The figure is to illustrate the application and principle. The power plug you get from t
Summary of the content on the page No. 20
Gigabit Smart Switch Grounding T erminal Equipotential Bonding Cable Ground Cable Grounding Bar Figure 3-3 Equipotential Bonding When equipotential bonding, please note that the cable should be copper wrapped 2 Kelly with its area being 6mm at least. The shorter cable the better, and use a grounding bar to establish an equipotential bonding point. Note: The equipotential bonding cable and ground cable are not provided with our product. If needed, please self purchase it. 212 Use Lightning Ar
