Summary of the content on the page No. 1
___________________
LOGO!
Preface
1
___________________
Getting started with LOGO!
LOGO! installation and
2
___________________
wiring
3
___________________
Programming LOGO!
4
___________________
LOGO! functions
LOGO!
UDF (User-Defined
5
___________________
Function) (0BA7 only)
Manual
__________________ 6_
Data Log (0BA7 only)
7
___________________
Configuring LOGO!
__________________ 8_
Applicable cards
9
___________________
LOG
Summary of the content on the page No. 2
Legal information Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal inju
Summary of the content on the page No. 3
Preface We thank you for purchasing LOGO! and congratulate you on your decision. With LOGO! you have acquired a logic module that meets the stringent quality requirements of ISO 9001. LOGO! can be used in many fields of applications. Due to its high functionality and easy operation, LOGO! offers you the utmost efficiency for almost any application. Purpose of this manual This LOGO! manual provides you with information about the creation of circuit programs, about the installation an
Summary of the content on the page No. 4
Preface Note Some chapters/sections in this manual specifically relate to the LOGO! 0BA7 devices. For easy identification, the names of these chapters/sections end with "(0BA7 only)". Valid range of this manual The manual applies to devices of series 0BA6 and 0BA7. New features of the LOGO! 0BA7 device series The following features are new for the LOGO! 0BA7 devices: ● New LOGO! Base Modules with an Ethernet interface and SD card slot Two new LOGO! versions LOGO! 12/24RCE and LO
Summary of the content on the page No. 5
Preface ● Support of configuration of elements connected to UDFs (User-Defined Functions) LOGO!Soft Comfort V7.0 provides a new circuit program editor - the UDF editor. Circuit programs created in the UDF editor can be saved as individual UDF blocks for use in an existing or a new circuit program in LOGO!Soft Comfort. A UDF block is a preconfigured circuit program that you create. If the circuit program in your LOGO! 0BA7 contains a UDF block, you can edit the elements connected to th
Summary of the content on the page No. 6
Preface ● Additional optional analog inputs and fast digital inputs are available on some of the LOGO! 0BA6 Base Modules. ● LOGO! 0BA6 configuration menus can be displayed in one of ten supported languages. You have a configuration choice to specify the language for LOGO! menus. ● New instruction blocks are available: Pulse Width Modulator (PWM), Mathematic Instruction, and Mathematic Instruction Error Detection. ● Message texts can tick on and off the display; can include bar graphs,
Summary of the content on the page No. 7
Preface Additional support Additional support is available on the Siemens website: Siemens LOGO! website (http://www.siemens.com/logo) LOGO! Manual, 04/2011, A5E03556174-01 7
Summary of the content on the page No. 8
Preface LOGO! 8 Manual, 04/2011, A5E03556174-01
Summary of the content on the page No. 9
Table of contents Preface ...................................................................................................................................................... 3 1 Getting started with LOGO!...................................................................................................................... 13 2 LOGO! installation and wiring .................................................................................................................. 29 2.1 Modular
Summary of the content on the page No. 10
Table of contents 3.7.6 Switching LOGO! to RUN mode ................................................................................................. 97 3.7.7 Second circuit program ............................................................................................................. 100 3.7.8 Deleting a block......................................................................................................................... 105 3.7.9 Deleting block groups.....................
Summary of the content on the page No. 11
Table of contents 4.4.13 Astronomical clock (0BA7 only) .................................................................................................195 4.4.14 Stopwatch (0BA7 only) ..............................................................................................................198 4.4.15 Up/down counter........................................................................................................................201 4.4.16 Hours counter..........................
Summary of the content on the page No. 12
Table of contents 10 Applications ........................................................................................................................................... 317 A Technical data ....................................................................................................................................... 319 A.1 General technical data .............................................................................................................. 319 A.2 Technical d
Summary of the content on the page No. 13
Getting started with LOGO! 1 Here's LOGO! LOGO! is a universal logic module made by Siemens that integrates: ● Controls ● Operator and display panel with background lighting ● Power supply ● Interface for expansion modules ● Interface for cards or cables, according to the device series: – If 0BA6, interface for a memory card, battery card, combined memory/battery card, LOGO! PC cable or USB PC cable – If 0BA7, interface for an SD card ● Interface for an optional text display (TD)
Summary of the content on the page No. 14
Getting started with LOGO! Which devices are available? LOGO! Base Modules are available in two voltage classes: ● Class 1 ≤ 24 V, i.e. 12 V DC, 24 V DC, 24 V AC ● Class 2 > 24 V, i.e. 115...240 V AC/DC LOGO! Base Modules are available in two versions: ● LOGO! Basic (version with display): 8 inputs and 4 outputs ● LOGO! Pure (version without display): 8 inputs and 4 outputs Each version is integrated into four (if 0BA6) or six (if 0BA7) subunits, is equipped with an expansion interf
Summary of the content on the page No. 15
Getting started with LOGO! Features of the LOGO! TD The LOGO! TD is available beginning with the 0BA6 series. It provides an additional display that is wider than the LOGO! Basic. It has four function keys that you can program in your circuit program as inputs. Like the LOGO! Basic, it has four cursor keys, an ESC key and an OK key that you can also program in your circuit program and use for navigation on the LOGO! TD. You can create and download a power-up screen for the LOGO!
Summary of the content on the page No. 16
Getting started with LOGO! Note The LOGO! Base Module may only be equipped with expansion modules of the same voltage class. Mechanical encoding pins in the housing prevent you from connecting devices of a different voltage class. Exception: The interface on the left side of an analog module or communication module is galvanically isolated. This type of expansion module can therefore be connected to devices of a different voltage class (Page 36). A LOGO! TD, if used, can be connect
Summary of the content on the page No. 17
Getting started with LOGO! The LOGO! structure Rx/Tx LINK Rx/Tx LINK ① Power supply ② Inputs ③ Outputs ④ PE terminal, for connecting to earth ground ⑤ RJ45 socket, for connection to Ethernet ⑥ Ethernet communication status LEDs (10/100 Mbit/s) ⑦ SD card slot with cap ⑧ LCD ⑨ Control panel ⑩ LOGO! TD cable connector ⑪ Expansion interface ⑫ Mechanic
Summary of the content on the page No. 18
Getting started with LOGO! ① Power supply ② Inputs ③ Outputs ④ Module slot with cap ⑤ Control panel (not for RCo) ⑥ LCD (not for RCo) ⑦ LOGO! TD cable connector ⑧ Expansion interface ⑨ Mechanical coding sockets LOGO! 18 Manual, 04/2011, A5E03556174-01
Summary of the content on the page No. 19
Getting started with LOGO! ① Power supply ② Inputs ③ Outputs ④ RUN/STOP LED ⑤ Expansion interface ⑥ Mechanical coding pins ⑦ Mechanical coding sockets ⑧ Slide LOGO! Manual, 04/2011, A5E03556174-01 19
Summary of the content on the page No. 20
Getting started with LOGO! ① Power supply ② Inputs ③ Outputs ④ RUN/STOP LED ⑤ Expansion interface ⑥ Mechanical coding pins ⑦ Mechanical coding sockets ⑧ Slide LOGO! AM2 ① Power supply ② Inputs ③ RUN/STOP LED ④ Expansion interface ⑤ Mechanical coding pins ⑥ Mechanical coding sockets ⑦ Slide ⑧ PE terminal, for connecting to earth ground and the shielding of analog measuring cables LOGO! 2
