Summary of the content on the page No. 1
0
Sim p lify
SANbox2-16 Fibre Channel Switch
Installation Guide
Firmware Version 4.1
59021-09 A Page i
Summary of the content on the page No. 2
SANbox2-16 Fibre Channel Switch Installation Guide 0 Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes onl
Summary of the content on the page No. 3
Table of Contents Section 1 Introduction 1.1 Intended Audience ............................................................................................. 1-1 1.2 Related Materials ............................................................................................... 1-1 1.3 New in this Release............................................................................................ 1-2 1.4 Safety Notices ..............................................................................
Summary of the content on the page No. 4
SANbox2-16 Fibre Channel Switch Installation Guide 0 2.1.3.2 Fan Fail LED (Amber)....................................................................... 2-3 2.1.3.3 Heartbeat LED (Amber).................................................................... 2-4 2.1.3.4 Input Power LED (Green) ................................................................. 2-4 2.2 Fibre Channel Ports ........................................................................................... 2-4 2.2.1 Port LEDs ...
Summary of the content on the page No. 5
SANbox2-16 Fibre Channel Switch Installation Guide 0 3.6 Fabric Management ......................................................................................... 3-12 Section 4 Installation 4.1 Site Requirements.............................................................................................. 4-1 4.1.1 Fabric Management Workstation............................................................... 4-1 4.1.2 Switch Power Requirements ....................................................
Summary of the content on the page No. 6
SANbox2-16 Fibre Channel Switch Installation Guide 0 5.1.2.2 Excessive Port Errors ....................................................................... 5-8 5.2 Chassis Diagnostics......................................................................................... 5-10 5.2.1 Chassis Over Temperature LED is Illuminated........................................ 5-11 5.2.2 Input Power LED Is Extinguished............................................................ 5-11 5.2.3 Fan Fail LED is Ill
Summary of the content on the page No. 7
SANbox2-16 Fibre Channel Switch Installation Guide 0 Admin Command.......................................................................................B-7 Alias Command .........................................................................................B-8 Config Command.....................................................................................B-10 Date Command .......................................................................................B-13 Fallback Command...........
Summary of the content on the page No. 8
SANbox2-16 Fibre Channel Switch Installation Guide 0 Figures Figure Page 2-1 SANbox2-16 Fibre Channel Switch................................................................................ 2-1 2-2 Chassis Controls and LEDS........................................................................................... 2-2 2-3 Chassis LEDs.................................................................................................................2-3 2-4 Fibre Channel Ports .........................
Summary of the content on the page No. 9
SANbox2-16 Fibre Channel Switch Installation Guide 0 Tables Table Page 2-1 Serial Port Pin Identification........................................................................................... 2-8 3-1 Zoning Database Limits ................................................................................................. 3-2 3-2 Port-to-Port Transmission Combinations ....................................................................... 3-5 3-3 Port-to-Port Latency...........................
Summary of the content on the page No. 10
SANbox2-16 Fibre Channel Switch Installation Guide 0 Notes Page x 59021-09 A
Summary of the content on the page No. 11
Section 1 Introduction This manual describes the features and installation of the SANbox2-16 Fibre Channel switch, firmware version 4.1. This manual is organized as follows: Section 1 describes the intended audience, related materials, safety notices, communications statements, laser safety information, electrostatic discharge sensitivity precautions, accessible parts, general program license, and technical support. Section 2 is an overview of the switch. It describes indicator LEDs and al
Summary of the content on the page No. 12
1 – Introduction New in this Release 0 Fibre Channel-10-bit Interface Rev. 2.3. Definitions of Managed Objects for the Fabric Element in Fibre Channel Standard (draft-ietf-ipfc-fabric-element-mib-04.txt). The Fibre Channel Standards are available from: Global Engineering Documents, 15 Inverness Way East, Englewood, CO 80112-5776 Phone: (800) 854-7179 or (303) 397-7956 Fax: (303) 397-2740. 1.3 New in this Release The following items are new in the current firmware release: Expanded zoning
Summary of the content on the page No. 13
1 – Introduction Safety Notices 0 1.4 Safety Notices A Warning notice indicates the presence of a hazard that has the potential of causing personal injury. 4-3, 4-14, 6-1 A Caution notice indicates the presence of a hazard that has the potential of causing damage to the equipment. 4-4, 5-16, 6-4 1.5 Sicherheitshinweise Ein Warnhinweis weist auf das Vorhandensein einer Gefahr hin, die möglicherweise Verletzungen zur Folge hat. 4-3, 4-15, 6-1 Ein Vorsichtshinweis weist auf das Vorhandensein ein
Summary of the content on the page No. 14
1 – Introduction Communications Statements 0 1.7 Communications Statements The following statements apply to this product. The statements for other products intended for use with this product appear in their accompanying manuals. 1.7.1 Federal Communications Commission (FCC) Class A Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against h
Summary of the content on the page No. 15
1 – Introduction Communications Statements 0 1.7.3 Avis de conformité aux normes du ministère des Communications du Canada Cet équipement ne dépasse pas les limites de Classe A d'émission de bruits radioélectriques por les appareils numériques, telles que prescrites par le Réglement sur le brouillage radioélectrique établi par le ministère des Communications du Canada. L'exploitation faite en milieu résidentiel peut entraîner le brouillage des réceptions radio et télé, ce qui obligerait le
Summary of the content on the page No. 16
1 – Introduction Communications Statements 0 1.7.5 VCCI Class A Statement This is a Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. 1.7.6 BSMI Class A Statement Warning: This is a Class A product. In a domestic environment, this product may cause radi
Summary of the content on the page No. 17
1 – Introduction Laser Safety Information 0 1.8 Laser Safety Information This product may use Class 1 laser optical transceivers to communicate over the fiber optic conductors. The U.S. Department of Health and Human Services (DHHS) does not consider Class 1 lasers to be hazardous. The International Electrotechnical Commission (IEC) 825 Laser Safety Standard requires labeling in English, German, Finnish, and French stating that the product uses Class 1 lasers. Because it is impractical to l
Summary of the content on the page No. 18
1 – Introduction Accessible Parts 0 1.10 Accessible Parts The Field Replaceable Units (FRUs) in the SANbox2-16 switch are the following: Small Form-Factor Pluggable (SFP) optical transceivers Power supplies Fans Refer to Section 6 Removal/Replacement for more information. 1.11 Pièces Accessibles Les pièces remplaçables, Field Replaceable Units (FRU), du commutateur SANbox2-16 Fibre Channel Switch sont les suivantes: Interfaces aux media d’interconnexion appelés SFP transceivers. Alimentati
Summary of the content on the page No. 19
1 – Introduction General Public License 0 1.13 General Public License QLogic® Fibre Channel switches are powered by the Linux® operating system. A machine-readable copy of the Linux source code is available upon written request to the following address. A nominal fee will be charged for reproduction, shipping, and handling costs in accordance with the General Public License. QLogic Corporation 6321 Bury Drive Eden Prairie, MN 55346-1739 Attention: Technical Support - Source Request Warning: I
Summary of the content on the page No. 20
1 – Introduction General Public License 0 We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original
