Summary of the content on the page No. 1
User’s Guide
Shop online at
www.omega.com
e-mail: info@omega.com
OME-PIO-D56/D24
PCI-Bus Digital I/O Board
Hardware Manual
Summary of the content on the page No. 2
® OMEGAnet Online Service Internet e-mail www.omega.com info@omega.com Servicing North America: USA: One Omega Drive, P.O. Box 4047 ISO 9001 Certified Stamford CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: ® USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA ® Customer Service: 1-800-622-2378
Summary of the content on the page No. 3
OME-PIO-D56/D24 User Manual OME-PIO-D56/OME-PIO-D24 User Manual (Ver.2.1, Oct/2003) ---- 1
Summary of the content on the page No. 4
Table of Contents 1. INTRODUCTION...........................................................................................................................3 1.1 FEATURES ....................................................................................................................................3 1.2 SPECIFICATIONS ...........................................................................................................................4 1.3 ORDER DESCRIPTION............
Summary of the content on the page No. 5
1. Introduction The OME-PIO-D56/OME-OME-PIO-D24 provides 56/24 TTL digital I/O lines. The OME-PIO-D56/OME-OME-PIO-D24 consists of one 24-bit bi-directional port, one 16-bit input port and one 16-bit output port (only for OME-PIO-D56). The 24-bit port supports three 8-bit groups PA, PB & PC. Each 8-bit group can be individually configured to function as either an input or an output. All groups using 24-bit bi- directional ports are configured as inputs upon power-up or reset. Use the OME
Summary of the content on the page No. 6
1.2 Specifications • All inputs are TTL compatible Logic high voltage : 2.4V (Min.) Logic low voltage : 0.8V (Max.) • All outputs are TTL compatible OPTO-22 output (CON3) Sink current : 64mA (Max.) Source current : 32mA(Max.) 16-channel output (CON1) Sink current : 8mA (Max.) Source current : 0.4mA(Max.) • Environmental : Operating Temperature: 0 °C to 60 °C Storage Temperature: -20 °C to 80 °C Humidity: 0 to 90% non-condensing • Dimensio
Summary of the content on the page No. 7
1.4 PCI Data Acquisition Family We provide a family of PCI bus data acquisition cards. These cards can be divided into three groups as follows: 1. OME-PCI-series: first generation, isolated or non-isolated cards OME-PCI-1002/1202/1800/1802/1602: multi-function family, non-isolated OME-PCI-P16R16/P16C16/P16POR16/P8R8: D/I/O family, isolated OME-PCI-TMC12: timer/counter card, non-isolated 2. OME-PIO-series: cost-effective generation, non-isolated cards OME-PIO-823/821: multi-function
Summary of the content on the page No. 8
PIO-D56 CON3 only for PIO-D56 PIO-D24 CON2 20 19 D/I DI/O 2 1 Port0 Port1 CON1 20 19 Port2 D/O 2 1 PCI BUS 2. Hardware configuration 2.1 Board Layout OME-PIO-D56/PIO-D24 User Manual (Ver.2.1, Oct/2003, PPH-005-21) ---- 6
Summary of the content on the page No. 9
2.2 I/O Port Location The OME-PIO-D56/OME-PIO-D24 consists of one 24-bit bi-directional port, one 16 bit input port and one 16 bit output port (only for OME-PIO-D56). The 24-bit port supports three 8-bit groups: PA, PB & PC. Each 8-bit group can be individually configured to function as either inputs or outputs. All groups using 24-bit bi- directional ports are configured as inputs upon power-up or reset. The I/O port locations are as follows: Connector of PA0 ~ PA7 PB0
Summary of the content on the page No. 10
I/O select (Sec. 3.3.7) RESET\ (Sec. 3.3.1) disable\ D/I/O Data input Latch (Sec. 3.3.8) Clock input D/O latch CKT disable Data Buffer input (Sec. 3.3.8) Clock input D/I buffer CKT • When the RESET\ is in Low-state all D/I/O operations are disabled • When the RESET\ is in High-state all D/I/O operation are enabled. • If D/I/O is configured as D/I port D/I= external input signal
Summary of the content on the page No. 11
2.3.2 DI Port Architecture (CON2) When the PC is powered up, all DI (CON2) port operations are disabled. The RESET\ signal controls the enable/disable signal for the DI port. Refer to Sec. 3.3.1 for more information about the RESET\ signal. • The RESET\ is in Low-state all DI operations are disabled • The RESET\ is in High-state all DI operations are enabled RESET\ disable Data CON2 Buffer input Clock input D/I buffer CKT OME-PIO-D56/OME-PIO-D24 User M
Summary of the content on the page No. 12
2.3.3 DO Port Architecture (CON1) When the PC is powered up, all DO port (CON1) operations are disabled. The RESET\ signal controls the enable/disable signal for the DI port. Refer to Sec. 3.3.1 for more information about the RESET\ signal. • The RESET\ is in Low-state all DO operations are disabled • The RESET\ is in High-state all DO operations are enabled The power-up states are as follows: • All DO operations are disabled • All output latches are cleared to Low-Level
Summary of the content on the page No. 13
2.4 Interrupt Operation All PC0, PC1, PC2 and PC3 can be used as an interrupt signal sources. Refer to Sec. 2.1 for PC0/PC1/PC2/PC3 location. The interrupt of OME-PIO-D56/OME- PIO-D24 is level-trigger & Active_High. The interrupt signal can be programmed to inverted or non-inverted state. The programming procedure is given as follows: 1. Make sure the initial level is High or Low 2. If the initial state is High select the inverted signal (Sec. 3.3.6) 3. If the initial state is Low s
Summary of the content on the page No. 14
2.4.1 Interrupt Block Diagram of OME-PIO- D56/D24 INT_CHAN_0 INT_CHAN_1 INT\ INT_CHAN_2 Level_trigger INT_CHAN_3 initial_low active_high The interrupt output signal of OME-PIO-D56/OME-PIO-D24, INT\ is Level_trigger & Active_Low. If the INT\ generates a low pulse, the OME-PIO- D56/OME-PIO-D24 will interrupt the PC only once. If the INT\ is fixed in low level, the OME-PIO-D56/OME-PIO-D24 will interrupt the PC continuously. INT_CHAN_0/1/2/3 must be controlled in a
Summary of the content on the page No. 15
2.4.2 INT_CHAN_0/1/2/3 INT_CHAN_0 (1/2/3) PC0(PC1/PC2/PC3) Inverted/Noninverted select INV0(1/2/3) Enable/Disable select EN0(1/2/3) The INT_CHAN_0 must normally be fixed in low level state and generate a high pulse to interrupt the PC. The EN0 (EN1/EN2/EN3) can be used to enable/disable the INT_CHAN_0(1/2/3) as follows : (Refer to Sec. 3.3.4) EN0 (1/2/3) = 0 → INT_CHAN_0(1/2/3) = disable EN0 (1/2/3) = 1 → INT_CHAN_0(1/2/3) = enable The INV0 c
Summary of the content on the page No. 16
2.4.3 Initial_high, active_low Interrupt source If the PC0 is a initial_high, active_low signal, the interrupt service routine should use INV0 to invert/non-invert the PC0 for high_pulse generation as follows: (Refer to DEMO4.C) Initial setting: now_int_state=1; /* initial state for PC0 */ outportb(wBase+0x2a,0); /* select the inverted PC0 */ void interrupt irq_service() { if (now_int_state==1) /* now PC0 is changed to LOW */(a) {
Summary of the content on the page No. 17
2.4.4 Initial_low, active_high Interrupt source If the PC0 is a initial_low, active_high signal, the interrupt service routine should use INV0 to inverted/non-inverted the PC0 for high_pulse generation as follows: (Refer to DEMO3.C) Initial setting: now_int_state=0; /* initial state for PC0 */ outportb(wBase+0x2a,1); /* select the non-inverted PC0 */ void interrupt irq_service() { if (now_int_state==1) /* now PC0 is changed to LOW */(c
Summary of the content on the page No. 18
2.4.5 Muliti-Interrupt Source Assume: PC0 is initial Low, active High, PC1 is initial High, active Low PC2 is initial Low, active High PC3 is initial High, active Low as follows : PC0 PC1 PC2 PC3 PC0 & PC1 are PC0 & PC1 are active at the same return to normal time. at the same time. PC2 & PC3 are PC2 & PC3 are return to normal at active at the same the same time. ti
Summary of the content on the page No. 19
void interrupt irq_service() { new_int_state=inportb(wBase+7)&0x0f; /* read all interrupt state */ int_c=new_int_state^now_int_state; /* compare which interrupt */ /* signal be change */ if ((int_c&0x1)!=0) /* INT_CHAN_0 is active */ { if ((new_int_state&0x01)!=0) /* now PC0 change to high */ { CNT_H1++; } else /* now PC0 change to low */
Summary of the content on the page No. 20
2.5 Daughter Boards 2.5.1 OME-DB-37 The OME-DB-37 is a general purpose daughter board for D-sub 37 pins, designed for an easy-wiring connection. 2.5.2 OME-DN-37 The OME-DN-37 is a general purpose daughter board for OME-DB-37 with DIN- Rail Mounting. It is designed for easy-wiring connection.. 37pin cable OME-DN-37 2.5.3 OME-DB-8125 The OME-DB-8125 is a general purpose screw terminal board. It is designed for easy wire connection. There i
