Metra Electronics GMLAN29-100 user manual

Device: Metra Electronics GMLAN29-100

Category: Car Amplifier

Manufacturer: Metra Electronics

Size: 0.75 MB

Added : 8/15/2013

Number of pages: 8

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Metra Electronics GMLAN29-100. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Metra Electronics GMLAN29-100.

For your convenience

If looking through the Metra Electronics GMLAN29-100 user manual directly on this website is not convenient for you, there are two possible solutions:

Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Metra Electronics GMLAN29-100 on full screen, use the button Fullscreen.
Downloading to your computer - You can also download the user manual Metra Electronics GMLAN29-100 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.

Metra Electronics GMLAN29-100 User manual - Online PDF

« Page 1 of 8 »

Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Metra Electronics GMLAN29-100 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Metra Electronics GMLAN29-100. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents

Summary of the content on the page No. 1

INSTALLATION INSTRUCTIONS FOR PART GMLAN29-100
GMLAN29-100
*Read Important Warning On Page 1
Before Attempting Any Installation*
The GMLAN29-100 is designed to and MUST be used with the
GMOS-100i (SOLD SEPERATELY). Please refer to GMOS-100i
for 20 pin connector instructions
APPLICATIONS
BUICK GMC
Acadia 2007-10
Enclave 2007-10
Lucerne 2006-10 Savanna 2008-10
Sierra (New body) 2007-10
CADILLAC Yukon 2007-10
Escalade 2007-10
DTS 2006-10 HUMMER
H2 2008-09
SRX 2007-09
PONTIAC
CHEVROLET
Avalanche

Summary of the content on the page No. 2

INTERFACE COMPONENTS •A) 4 pin harness with stripped leads •B) 22 pin to 30 pin GM harness •C) 16 pin backup camera harness •D) 16 pin RSE harness A B 4 pin C D TOOLS REQUIRED FOR INSTALLATION •Cutting Tool •Tape •Crimping Tool •Connectors (I.E. butt-connectors, bell caps, ECT…) M2.6 6 2.5 1.5 IGNITION TERMINALS WIRE CUTTER ISO M3.5 M4 M3 M5

Summary of the content on the page No. 3

TABLE OF CONTENTS Installing The Interface .............................................................. 1 Installing The GMLAN29-100 ................................................. 1 Programming SWC ..................................................................... 2 Testing The GMLAN29-100 ...................................................... 2 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics s

Summary of the content on the page No. 4

*Important: Before beginning any of the following, disconnect the negative battery terminal to prevent an accidental short circuit. INSTALLING THE INTERFACE From the 22 way harness: • Connect the Black wire with the ring terminal to the back of the aftermarket radios chasis • Connect the 3.5mm jack to your aftermarket radios steering wheel control input (if equipped) From the 30 way harness: • Connect the Black wire to the ground wire of the aftermarket radio • Connect the RCA’s on the 8 p

Summary of the content on the page No. 5

PROGRAMMING SWC • Turn on the ignition • The LED will begin to blink rapidly • Turn on the aftermarket radio • Press volume up until radio responses TESTING THE GMLAN29-100 • Turn the ignition on, and then turn the aftermarket radio on. • Push the Onstar button, the radio should turn off (radio will mute if mute wire is connected) and you should hear Onstar. Push the Onstar cancel button and the radio should come back on. 2

Summary of the content on the page No. 6

NOTES

Summary of the content on the page No. 7