Summary of the content on the page No. 1
User’s Manual
HSA 400 & HSA 402 US/Domestic
HSA 400 & HSA 402 International
®
Hideaway Surface Access Products
68-604-01 Rev. F
08 08
© 2008 Extron Electronics. All rights reserved.
Summary of the content on the page No. 2
Precautions Safety Instructions • English Warning Extron’s Warranty Power sources � This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. The third (grounding) pin is in the literature provided with the equipment. Extron Electronics warrants this product agains
Summary of the content on the page No. 3
Summary of the content on the page No. 4
Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About the Hideaway Surface Access Products ...................................................................................... 1-2 Features ...................................................................................... 1-3 Chapter 2 � Installation ............................................................. 2-1 Installation Overview ...............................................
Summary of the content on the page No. 5
Table of Contents, cont’d HSA 400/402 Series Surface Access Products Chapter One 1 Introduction About the Hideaway Surface Access Products Features 68-604-01 Rev. F 08 08 All trademarks mentioned in this manual are the properties of their respective owners. iv HSA 400/402 Series � Table of Contents
Summary of the content on the page No. 6
Introduction ® The installed enclosures fit nearly flush within a table or podium About the Hideaway Surface Access Products top, storing the AAPs and connectors out of the way and out of The patented Extron Hideaway HSA 400 and HSA 402 are sight. To access the AAPs and connectors, the user presses furniture-mounted, architectural solutions for inconspicuous down on the top of the enclosure, releasing a mechanical latch. computer video interface connector access and control. A gas lift slowly t
Summary of the content on the page No. 7
AUDIO INPUT COMPUTER H. SHIFT SELECT RGB 580xi SI AAP INPUTS SOG V-SYNC WIDTH AUDIO ANALOG C AO B N T CR O D L E VIDEO OUTPSU E DR T DR SP NC EG O M SP Y N SC YNC LEVEL PEAKING RGB 580xi HSA 402 240 - 50/60 Hz 5A 240 - 50/60 Hz 5A SIELP E T T M P TE AUD IO . S I FT i I R GB 580x S AA P N U C CO U R H H HSA 402 24 0 - 50 / 60 Hz 5A 24-0 50 / 60 Hz A 5 Introduction, cont’d HSA 400/402 Series Surface Access Products Projector Extron HSA 402 Extron RGB 580xi SI AAP Chapter Two Extron HSA 402 2 M
Summary of the content on the page No. 8
Width of Mounting Surface Installation Installation Overview Preparing the Routing Template Install and set up the HSA surface access enclosure as follows: Extron provides a metal template for each HSA model at no charge. Appendix A lists the HSA 400/402 template part 1 If you have an unprepared mounting template, prepare numbers. Extron recommends using this template as a guide to the template. See “Preparing the Routing Template” in cut the hole in the table where the HSA will be installed.
Summary of the content on the page No. 9
Installation, cont’d Preparing the Table and Mounting the Enclosure The preferred and recommended method for preparing the table is to use the appropriate Extron metal routing template and a router. The templates are available at no cost. See the part numbers for the templates in appendix A, “Reference Information”. Alternatively, you can use a paper cut-out template (see appendix A, “Reference Information”) and a sabre saw or keyhole saw, but this method is not recommended. Prepare the table
Summary of the content on the page No. 10
AUDIO INPUT COMPUTER SELECT H. SHIFT RGB 580xi SI AAP HSA 400 125 - 50/60 Hz 5A HSA 400 240 - 50/60 Hz 5A Installation, cont’d 7. Carefully lower the HSA enclosure into the hole to test the Cabling and Installing the AAPs fit. If necessary, remove the enclosure and use a file or The space behind the AAP panel is limited. The on-line rasp to enlarge or smooth the edges of the opening. Connectivity Configurator, available at 8. From the underside of the table, bolt the clamshell to the www.extro
Summary of the content on the page No. 11
125 50/60 Hz 0.5A AUDIO INPUT COMPUTER SELECT HSA 400 Installation, cont’d 3. Insert each of the AAP’s screws through the holes in the Cabling the Enclosure AAP opening of the front panel. Secure each AAP to the HSA 400 panel with the provided captive washers and #4-40 nuts 120-240 50/60 Hz 5A (figure 2-5). AUDIO #4-40 Nut with Captive INPUT COMPUTER SELECT Washer H. SHIFT RGB 580xi SI AAP Front Panel Front Panel View 1A 1B 1A 1B 2 3 Cable RGB 580xi SI AAP Figure 2-5 — Mount
Summary of the content on the page No. 12
Installation, cont’d HSA 402 The Universal AC outlet is fully compatible with Europlug, British, Indian, Danish, and Italian plug 120-240 50/60 Hz 5A 120-240 50/60 Hz 5A types. See the universal AC outlet guide on the Extron AUDIO Web site, www.extron.com, for compatibility details on INPUT COMPUTER SELECT H. SHIFT all plug types. RGB 580xi SI AAP 3 Cable access holes Cabling the RJ-45 connectors Front Panel View 1A 1B 1C 1D Plug one end of a twisted pair (TP) cable into each o
Summary of the content on the page No. 13
Installation, cont’d Routing the AAP Cables Bezels The AAP cables must have freedom of movement to permit The HSA ships with RJ-45/RJ-11 connector bezel plug-ins in a opening and closing the surface mount enclosure. At the same variety of colors and a black, blank bezel. Bezel time, they need to be restrained to prevent their rubbing against To change to a different color connector bezel, the edges of the enclosure cable access hole in the underside of or if a connector is not needed or desired
Summary of the content on the page No. 14
Installation, cont’d HSA 400/402 Series Surface Access Products Chapter Three 3 Maintenance and Modifications Replacing an AAP Replacing the Bezels Removing and Replacing the Enclosure Replacing the Gas Lift Adjusting the Top Surface Level 2-14 HSA 400/402 Series � Installation
Summary of the content on the page No. 15
125 50/60 Hz 0.5A 125 - 50/60 Hz 5A AUDIO INPUT COMPUTER SELECT H. SHIFT RGB 580xi SI AAP AUDIO INPUT COMPUTER SELECT HSA 400 HSA 400 Maintenance and Modifications The HSA surface mount enclosures can be modified in the 4. Remove the AAP(s) to be replaced from the front panel by future to replace an AAP or to change the color or appearance of unscrewing the nuts on the rear of the panel that fasten the the bezel plug-ins. The most probable corrective maintenance plates to the faceplate (fi
Summary of the content on the page No. 16
Maintenance and Modifications, cont’d Replacing the Bezels Removing and Replacing the Enclosure The HSA ships with RJ-45/RJ-11 connector bezel plug-ins in a The procedure for replacing the gas lift requires removing the variety of colors and a black, blank bezel. Replace a bezel as HSA 400 or HSA 402 from the table. Adjusting the top surface follows: level may also require removal of the HSA from the table. Remove and replace the surface mount enclosure as follows: 1. Remove the four hex head
Summary of the content on the page No. 17
125 - 50/60 Hz 5A AUDIO INPUT COMPUTER SELECT H. SHIFT RGB 580xi SI AAP 125 - 50/60 Hz 5A HSA 402 Maintenance and Modifications, cont’d The flanged edges of the top of the surface enclosure 9. Perform the desired maintenance procedure. CAUTION are bevelled to an ultra-fine thickness of less than 10. If the surface is not level, adjust the top surface. See 0.04 (4/100)" (approximately 1 mm). These edges “Adjusting the Top Surface Level”, later in this chapter. are soft and can be easily nicked
Summary of the content on the page No. 18
Maintenance and Modifications, cont’d 4. Turn the gas lift mounting plate counterclockwise until the Replacing the Gas Lift pivot nut on the plate comes free from the shaft of the gas The gas lift that raises the HSA surface is rated for 100,000 lift (figure 3-7). opening and closing cycles. Replace the gas lift as follows: Ensure that AC power is disconnected before Top Panel servicing the HSA unit. Clevis Bracket When the HSA 400/402 is upside-down, the latch CAUTION may be ineffective. If t
Summary of the content on the page No. 19
Maintenance and Modifications, cont’d Adjusting the Top Surface Level HSA 400/402 Series Surface Access Products Level the top surface of the HSA as follows: 1. If necessary, in order to view the surface and the underside of the enclosure simultaneously, remove the surface mount enclosure from the table. See “Removing and Replacing the Enclosure”, steps 1 through 8. 2. If necessary, close and latch the top panel. 3. Slightly loosen the two latch locking screws (figure 3-8) on the underside of t
Summary of the content on the page No. 20
Reference Information Clamshell (figure A-1) A = 5.25" (13.3 cm) Specifications B = 7.75" (19.7 cm) C = 7.75" (19.7 cm) General HSA 402 US/domestic The Universal AC outlet is fully compatible with Europlug, Top plate (outer rim) 10.844" W x 6.425" D (27.54 cm W x 16.32 cm D) British, Indian, Danish, and Italian plug types. See the Top plate (tilt plate) . 8.894" W x 4.475" D Universal AC outlet guide on the Extron Web site, (22.59 cm W x 11.37 cm D) www.extron.com, for compatibility details on a
