Summary of the content on the page No. 1
ISS 506
Integration Seamless Switcher
68-1077-01 Rev. B
06 09
Summary of the content on the page No. 2
Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source indicated on the product. This This symbol is intended to alert the user of important operating and maintenance equipment is intended to be used with a main power system with a grounded (neutral) conductor. The (servicing) instructions in the literature provided with the equipment. third (grounding) pin is a safety feature, do not attempt to bypass or disable it. Th
Summary of the content on the page No. 3
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is
Summary of the content on the page No. 4
Summary of the content on the page No. 5
Table of Contents Chapter One • Introduction ......................................................................................................1-1 About this Manual .....................................................................................................................1-2 About the Integration Seamless Switchers ...............................................................1-2 Features ............................................................................................
Summary of the content on the page No. 6
Table of Contents, cont’d Output Configuration menu.............................................................................................3-11 Resolution and refresh rate submenu ........................................................................3-12 Output Type submenu .................................................................................................3-13 Sync Polarity submenu ........................................................................................
Summary of the content on the page No. 7
Toggling background illumination on and off ...................................................................3-37 Using front panel security lockouts (executive modes) .....................................................3-38 Rear Panel Reset Button ......................................................................................................3-39 Performing soft system resets .............................................................................................
Summary of the content on the page No. 8
Table of Contents, cont’d Using the Command/Response Tables .........................................................................4-11 Command/response table for SIS commands .........................................................4-12 Command/Response Table for IP SIS Commands .................................................4-35 Symbol definitions ..................................................................................................................4-35 Special Characters .....
Summary of the content on the page No. 9
Button Label Generator .......................................................................................................5-27 Using the Button Label Generator software ......................................................................5-27 Special Characters ...................................................................................................................5-28 Chapter 6 • HTML Operation .................................................................................
Summary of the content on the page No. 10
Table of Contents, cont’d Chapter 7 • Modifications ...........................................................................................................7-1 Opening the Switcher ..............................................................................................................7-2 Installing an Optional SDI/HD-SDI Input Board .......................................................7-3 Installing an Optional Output Board .............................................................
Summary of the content on the page No. 11
ISS 506 Integration Seamless Switcher Chapter One 1 Introduction About this Manual About the Integration Seamless Switchers Features
Summary of the content on the page No. 12
Introduction About this Manual This manual contains installation, configuration, and operating information for the Extron ISS 506 family of 6-input Integration Seamless Switchers with audio. About the Integration Seamless Switchers The Extron ISS 506 is a family of scaling, video and stereo audio seamless switchers. The ISS 506 family consists of the following five models: • ISS 506 — Six-input seamless video switcher with audio • ISS 506 DI/DVI — Six-input seamless video switcher with audi
Summary of the content on the page No. 13
LCD Display (preview) LCD Display (program) Projector Control System with RS-232 Extron Ethernet ISS 506 Seamless Switcher TCP/IP Network PC TV Tuner PC DVD/VCR Sound System Camera Codec Document Camera Figure 1-1 — Typical ISS 506 Integration Seamless Switcher application The switcher inputs all video signal formats on a combination of connectors as follows: • Inputs 1 through 4 — Four sets of five BNC connectors that can input RGBHV, RGBS, YUV-HD, YUVp, RGBcvS, YUVi, S-video, or composite
Summary of the content on the page No. 14
Introduction, cont’d The ISS receives and outputs the stereo audio on 5-pole captive screw connectors. The audio can be switched with cross fading (that is, the previous audio channel fades out and then the new audio channel fades in). For upscaling, the ISS 506 converts the horizontal and vertical sync timing and the number of lines of the lower-resolution video input to match the native resolution of the display. This produces an undistorted, brighter picture than an unscaled input woul
Summary of the content on the page No. 15
Audio outputs — The ISS outputs the selected unamplified, line level, balanced or unbalanced stereo or mono audio on 5-pole captive screw connectors. Operational flexibility — Operations such as input selection, transitions, and picture adjustments, and volume control can be performed on the front panel or via the Ethernet or serial link. The serial links allow remote control via a PC or control system. The Ethernet link allows multiple remote links with two levels of password protecti
Summary of the content on the page No. 16
Introduction, cont’d Transitions — Control the type of switch that occurs between the preview and program outputs. The Cut button creates an instant switch between the preview and program outputs. The Wipe and Dissolve buttons switch with a masking effect. Test patterns — The switcher features built-in test patterns to aid in monitor or projector setup and evaluation. Blue mode — The switcher can be set to output the blue video signal only, to help installers calibrate the monitor or proj
Summary of the content on the page No. 17
ISS 506 Integration Seamless Switcher Chapter Two 2 Installation Mounting the Switcher Cabling and Rear Panel Views Front Panel Configuration Port Configuration
Summary of the content on the page No. 18
Installation Mounting the Switcher Four uninstalled rubber feet are included with the seamless switcher. If you are going to rack mount the switcher, mount it before you cable it (see “Rack mounting”, below), and do not install the rubber feet. If you are not rack mounting the seamless switcher, see “Tabletop placement”, below. Tabletop placement For tabletop placement, install the self-adhesive rubber feet/pads (provided) onto the four corners of the bottom of the seamless switcher. Rack
Summary of the content on the page No. 19
Mounting instructions For optional rack mounting, do not install the rubber feet. Mount the ISS 506 in a rack as follows: 1. Attach the included MBD 249 rack/through-desk mounting brackets to the unit, using eight machine screws supplied with the mounting kit (figure 2-1). Use the lower screw holes in the brackets. MBD 249 2-U Rack Mount Bracket (use four lower holes) Figure 2-1 — Mounting the seamless switcher 2. Insert the unit into the rack and align the holes in the mounting bracket
Summary of the content on the page No. 20
Installation, cont’d Cabling and Rear Panel Views All connectors are on the rear panel (figure 2-2). 2 3 4 6 8 13 9 PREVIEW PROGRAM R/ G/Y B/C H/HV V R/ G/Y B/C H/HV V VID VID VID SD SDII RGB/R-Y, Y, B-Y 100-240V 1 3 5 5 6 6 R-Y VID B-Y R-Y VID B-Y /Y /Y 50/60 Hz 2A MAX I R G B/ LAN N O R-Y /Y B-Y RGB/R- RGB/R-Y, Y, Y, Y, B- B-Y Y RS232/422 4 P 2 U RESET T U T P R/ G/Y B/C V R/ G/Y B/C R-Y B-Y H V S H/HV H/HV V YC S R-Y VID B-Y VID B-Y /C U R-Y PR PROGRAM OGRAM PREVIEW PREVIEW T S L 1 R L
