Enterasys Networks Smart 6000 user manual

Summary of the content on the page No. 1

SmartSwitch 6000 and
Matrix E7 Modules
User’s Guide

Summary of the content on the page No. 2

Summary of the content on the page No. 3

Notice Enterasys reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Enterasys to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL ENTERASYS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFIT

Summary of the content on the page No. 4

Restricted Rights Notice (Applicable to licenses to the United States Government only.) 1. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013. Enterasys, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505. 2. (a) This computer software is submitted with restricted rights. It may not be used, reproduced, or disclosed by the Government

Summary of the content on the page No. 5

iii

Summary of the content on the page No. 6

Contents Chapter 1 Introduction Using the SmartSwitch 6000 and Matrix E7 User’s Guide ............................................. 1-5 Related Manuals .............................................................................................................. 1-7 Getting Help..................................................................................................................... 1-7 Using On-line Help.................................................................................

Summary of the content on the page No. 7

Contents Using an Uninterruptable Power Supply (UPS) ..................................................... 2-51 Accessing the UPS Window............................................................................ 2-51 Setting the UPS ID .......................................................................................... 2-53 Using the Test Option ...................................................................................... 2-53 Using the Disconnect Option..........................

Summary of the content on the page No. 8

Contents Chapter 4 Alarm Configuration About RMON Alarms and Events ................................................................................... 4-1 Basic Alarm Configuration.............................................................................................. 4-2 Accessing the Basic Alarm Configuration Window................................................. 4-3 Viewing Alarm Status........................................................................................ 4-3 Creatin

Summary of the content on the page No. 9

Contents Chapter 6 FDDI Management Viewing FDDI Information.............................................................................................. 6-1 Configuration ............................................................................................................ 6-3 Connection Policy..................................................................................................... 6-6 Station List................................................................................

Summary of the content on the page No. 10

Chapter 1 Introduction About the SmartSwitch 6000 and Matrix E7 families; how to use this guide; related guides; getting help. Welcome to the Element Manager for the SmartSwitch 6000 and Matrix E7 Modules User’s Guide. This guide is a reference for using NetSight Element Manager for the SmartSwitch 6000 and Matrix E7 products. The SmartSwitch 6000 and Matrix E7 products encompass the 6C105 chassis (for the 6000) and 6C107 chassis (for the Matrix E7), as well as the SmartSwitch 6000 and Matr

Summary of the content on the page No. 11

Introduction The SmartSwitch 6000 and Matrix E7 modules include: •The 6E122-26 and 6E123-26 SmartSwitch modules each provide 24 fixed 10Base-T switch ports (via RJ45 connectors on the 6E122; RJ21 Telco connectors on the 6E123) and two slots for optional FE-100xx Fast Ethernet Port Interface Modules (FEPIMs). Several Fast Ethernet port modules are available: - the FE-100FX, which provides one multi-mode fiber port via an SC connector; - the FE-100TX, with one Category 5 UTP RJ45 connector;

Summary of the content on the page No. 12

Introduction The HSIM-W6 and HSIM-W84 are intelligent devices that are functionally identical to the NOTE CSX400. These HSIMs require their own IP addresses, and are managed as individual devices rather than as part of the device in which they are installed. Refer to the CSX200 and CSX400 User’s Guide for details on managing these devices using NetSight Element Manager. - The HSIM-W87 is a Wide Area Network (WAN) HSIM that provides LAN to WAN connectivity for any SmartSwitch that supports h

Summary of the content on the page No. 13

Introduction •The 6H123-50 SmartSwitch module is a 48 port MicroLAN 10/100 Mbps Ethernet module (4 separately repeated MicroLANs of 12 ports each, via four RJ21 Telco connectors). The 6H123-50 also provides two FEPIM slots for uplinks. •The 6H133-37 SmartSwitch module is a 36 port MicroLAN 10/100 Mbps Ethernet module (3 separately repeated MicroLANs of 12 ports each, via RJ21 Telco connectors). A single HSIM slot is also provided. •The 6H122-08, 6H128-08, and 6H129-08 SmartSwitch modules eac

Summary of the content on the page No. 14

Introduction •The 6M146-04 SmartSwitch carrier module provides two FEPIM slots and two HSIM slots. Each of these SmartSwitch modules provide key mission-critical features such as redundant links for load sharing, alarm thresholding, broadcast storm control, port redirecting for traffic analysis, traffic priority configuration, and full error breakdown. Per-port RMON support is also provided. By default, these modules perform traditional switching (or bridging); each can also be configured t

Summary of the content on the page No. 15

Introduction Chapter 1, Introduction, provides a list of related documentation and shows you how to contact the Enterasys Global Call Center. It also briefly describes the SmartSwitch 6000 and Matrix E7 modules and 6C105/6C107 chassis. Chapter 2, The Device View, describes the visual display of the SmartSwitch 6000 and Matrix E7 chassis as a whole and explains how to use the mouse within the Device View. It also details all chassis-level management functions, including Find Source Address,

Summary of the content on the page No. 16

Introduction The Element Manager Chassis User’s Guide discusses how to initially configure the NOTE SmartSwitch 6000 or Matrix E7 chassis using the Chassis Setup window. It gives an overview of SmartSwitch 6000 and Matrix E7 management views and general module information, and discusses changing the current view as well as the default view. Related Manuals The SmartSwitch 6000 and Matrix E7 User’s Guide is only part of a complete document set designed to provide comprehensive information ab

Summary of the content on the page No. 17

Introduction From the Help menu accessed from the Device View window menu bar, you can access on-line Help specific to the Device View window, as well as bring up the Chassis Manager window for reference. Refer to Chapter 2, The Device View, for information on the Device View and Chassis Manager windows. All of the online help windows use the standard Microsoft Windows help facility. If you NOTE are unfamiliar with this feature of Windows, you can select Help from the Windows Start menu, or

Summary of the content on the page No. 18

Introduction 7HOHSKRQHKRXUVDGD\GD\VD\HDU )D[ (OHFWURQLF0DLOVXSSRUW#HQWHUDV\VFRP 0DLOLQJ$GGUHVV (QWHUDV\V1HWZRUNV,QF 7HFKQLFDO6XSSRUW ,QGXVWULDO:D\ 5RFKHVWHU1+ )73 IWSFDEOHWURQFRP /RJLQDQRQ\PRXV 3DVVZRUG\RXUHPDLODGGUHVV Getting Help 1-9

Summary of the content on the page No. 19

Introduction 1-10 Getting Help

Summary of the content on the page No. 20

Chapter 2 The Device View Information displayed in the Device View; the logical Device View; the Chassis Manager window; chassis management functions The Device View displays the current configuration of your SmartSwitch 6000 or Matrix E7 module via a graphical representation of the module’s front panel. The Device View serves as a single point of access to all other SmartSwitch 6000 and Matrix E7 windows and screens, which are discussed at length in the following chapters. To access the Dev