Summary of the content on the page No. 1
16-Port 10/100Mbps
Smart Switch
(VLAN, Trunking & Fiber Option)
ES-3116RE+
User’s Manual
Summary of the content on the page No. 2
FCC Class B Certification This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1.This device may not cause harmful interference, and 2.This device must accept any interference received, including interference that may cause undesired operation. Warning! This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro
Summary of the content on the page No. 3
1. Introduction Congratulations on your purchase of this 16-port Smart Fast Ethernet Switch. This high performance switch provides sixteen fast ethernet ports to segment network traffics, extend fast ethernet connection distance, and convert data packets between different transmission speeds. This Switch provides sixteen shielded RJ-45 ports. These are 10BaseT/100BaseTX Auto-negotiation ports. This switch utilize stored-and-forward switching architecture that filters and forwards data
Summary of the content on the page No. 4
2. Features & Specifications (1) Features Comply with IEEE 802.3 10BaseT and IEEE 802.3u 100BaseTX Standards. Provide 16 UTP ports with 10/100Mbps Auto-Negotiation. Provide one uplink port which can connect to another hub/switch using a normal UTP cable One 100Mbps Fiber-SC/ST module option (Support Full/Half Duplex) Support IEEE 802.3x compliant full-duplex flow control, half-duplex flow control Full wire speed on every port. Support Port-based VLAN Support 2 Trunking Group
Summary of the content on the page No. 5
(2) Specifications Standards : IEEE 802.3 10BaseT and IEEE 802.3u 100BaseTX 10/100Mbps Ports : RJ-45 x 16 Uplink Port : RJ-45 x 1 100Mbps Fiber-SC/ST Port : Optional Switching Architecture : Store and Forward MAC Address : 8K Buffer : 512Kbyte Flow Control : Back pressure and IEEE 802.3x VLAN : Port-based VLAN up to 16 groups Trunking : 2 groups N-Way Auto-Negotiation : on all ports Full-Duplex / Half-Duplex : on all ports Switch LED : Power Port LEDs : Link/A
Summary of the content on the page No. 6
3. Package Contents One Fast Ethernet Switch One Power Cord One User’s manual Rackmount accessories
Summary of the content on the page No. 7
4. Physical Description (1) Panel Front View Control Button LED RJ-45 Connectors Rear View Power Connector AC 100-240V SW I o POWER Expansion Slot Power Switch LED/Button Panel Normal : Full Duplex / Collision Normal : 100Mbps Setup : Group Setup : Port Power LED Normal : Link / Activity Setup Setup : Status Buttons Setup Functions
Summary of the content on the page No. 8
(2) LED LED Status Description Power is supplied On System Power No Power Off Collision detected in On FUL/COL this segment (Full Duplex/Collision) Off No Collision A valid link is On established LNK/ACT Normal Data packets Flash (Link/Activity) received Port No link is established Off This port run at On 100M 100Mbps (100Mbps) No connected or run Off at 10Mbps This group is in On setting mode Group This group is not in Off setting This port is in setting
Summary of the content on the page No. 9
5. Installation (1) Operating Environment This 16 ports smart switch must be installed and operated within the limits of specified operating temperature and humidity (see previous section under Specifications). Do not place objects on top of the unit. Do not obstruct any vents at the sides of the unit. Do not position the unit near any heating source such as heater, radiator, or direct exposure to sun. Prevent entering of water and moisture into the unit. If necessary, use dehumidifier t
Summary of the content on the page No. 10
6. Advance Configuration This switch provides advance features which offer you more flexibility in setting up your network. The following section explain how to setting up the VLAN, Trunking, Speed and Full/Half duplex modes. (1) VLAN Virtual LAN (VLAN) is a logical subgroup within a local area network which can be configure through port configuration. VLAN can be configured to optimize traffic or to isolate specific workstations for reasons of security or convenience. Each
Summary of the content on the page No. 11
Step 4. Press the Set button to assign the selected port to the VLAN group. After you press Set button ,the selected port LED will switch between on and off. If the selected port LED is on, the selected port is added to the VLAN group. If the selected port LED is off, the selected port is removed from the VLAN group. Step 5. Repeat steps 3 to 4 to assign other ports to the selected VLAN group. Step 6. When you finish one VLAN group configuring, press the Group button to scroll to the next
Summary of the content on the page No. 12
1.2Gbps Trunk and 800Mbps Trunk Port trunking Configuration This switch provides two Port trunking groups listed in following table. Group Mode Ports Description 1 1,9 two ports trunking A 2 1, 2, 9, 10 four ports trunking 3 1, 2,3,9,10,11 six ports trunking 1 7,15 two ports trunking B 2 7,8,15,16 four ports trunking The following instructions describe how to configure port trunking. Note : 1.Trunking port work in 100M full-duplex. 2.The trunking ports must be configur
Summary of the content on the page No. 13
(3) Speed (100M / 10M) Configuration This switch provides the force speed function. You can refer the following procedure to setup the speed of switching ports. Step 1. Press the Function button until the Speed LED is on. Step 2. Press the Port button to scroll between the port 1 to 16. Step 3. Press the Set button to assign the speed of selected port to 100Mbps or 10Mbps. After you press Set button ,the selected port’s 10M (Status) LED and 100M (Group) LED will switch between on and of
Summary of the content on the page No. 14
Half Duplex. If the selected port Full LED is on and Half LED is on, the select port is set to auto negotiation. Step 4. Press the Function button until the SAVE LED is on. Step 5. Press the Set button to save the setting. Step 6. Press the Function button to return to normal mode.
Summary of the content on the page No. 15
7. Trouble-shooting 1. Power LED is not lit Check if the power cord is properly connected to the power outlet and the hub. Make sure the power switch on the hub is turned ON. 2. 100M Link is not lit when connect to 100Mbps device Check the power switch of the network device attached to the switch; make sure it is turned ON. Check the network cable; make sure it is properly connected to the switch and the network device. Check the network cable; make sure the UTP cables comply wit
