Summary of the content on the page No. 1
Quick Start Guide
Cisco Small Business
SLM2048, SLM2024, SLM248G, SLM248P, SLM224G,
SLM224P Smart Switch
Package Contents
• Smart Switch
• Power Cord
• Rubber feet
• Quick Start Guide
• Mounting Hardware
• Product CD-ROM
Summary of the content on the page No. 2
Welcome Thank you for choosing the Cisco Small Business Series Smart Gigabit Switch. The Smart Switches offer the following interfaces: • The SLM2024 and SLM2048 offer twenty four (24) or forty eight (48) gigabit copper ports, with two (2) shared copper or optical (SFP) uplink interfaces for connecting the switch to the core network. • The SLM224G, SLM224P, SLM248G, and SLM248P offer twenty four (24) or forty eight (48) 10/100 copper ports, with two (2) shared gigabit copper or optical (SFP
Summary of the content on the page No. 3
To establish a Fast Ethernet connection using a miniGBIC port, you will need to install a MFEFX1 (100BASE-FX) or MFELX1 (100BASE-LX) 100SFP transceiver and use fiber optic cabling. NOTE On the SLM2024 and SLM2048, miniGBIC ports are shared with standard ports. If a miniGBIC port is used, then the shared standard port on the switch cannot be used. The following table defines the shared port mapping of the SLM2024 and SLM2048 switch. Switch Model miniGBIC Port Standard Port SLM2024 miniGBIC
Summary of the content on the page No. 4
G1-G2 — The switch is equipped with two autosensing gigabit Ethernet network ports, which use RJ-45 connectors. The gigabit Ethernet ports support network speeds of 10 Mbps, 100 Mbps, or 1000 Mbps. They can operate in half- and full-duplex modes. Auto-sensing technology enables each port to automatically detect the speed of the device connected to it (10 Mbps, 100 Mbps, or 1000 Mbps), and adjust its speed and duplex accordingly. To establish a gigabit Ethernet connection using a miniGBIC p
Summary of the content on the page No. 5
in half- and full- duplex modes. Auto-sensing technology enables each port to automatically detect the speed of the device connected to it (10 Mbps or 100 Mbps), and adjust its speed and duplex mode accordingly. miniGBIC — (1-2) The miniGBIC (gigabit interface converter) port is a connection point for a miniGBIC expansion module, so the switch can be uplinked to another switch by using a fiber optical link. The miniGBIC port provides a link to a high-speed network segment or individual work
Summary of the content on the page No. 6
• Ambient Temperature — To prevent the switch from overheating, do not operate it in an area that exceeds an ambient temperature of 104°F (40°C). •Air Flow — Be sure that there is adequate air flow around the switch. •Mechanical Loading — Be sure that the switch is level and stable to avoid any hazardous conditions. •Reliable earthing — Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections t
Summary of the content on the page No. 7
STEP 5 Connect the switch to network devices according to the the installation instructions in section 4, “Connecting the Equipment”. Getting Started with the 3 Configuration Before you begin to use the Configuration Utility, make sure that you have a computer that meets the following requirements: • Internet Explorer (version 6 or higher) or Firefox (version 3 or higher). • The Web-based configuration utility is optimized for a screen resolution of 1024 x 768. To get started configuring you
Summary of the content on the page No. 8
NOTE If you have changed the switch IP address or are using DHCP to assign it, enter the new IP address assigned to the switch. The ip address of the computer you are using to configure the switch, must be on the same subnet as the switch. STEP 4 When the login page appears, enter the user name and password. The default user name is admin. The default password is admin. Passwords are case sensitive. STEP 5 Click Login. STEP 6 Follow the on-screen prompts to complete the initial configurati
Summary of the content on the page No. 9
If the above recommendations do not work, try the same steps by using a different computer. The switch might have some hardware problems if the second computer also fails to establish a link, please contact technical support for further assistance. NOTE If you need help resolving a problem, visit the Cisco Small Business Support Community at www.cisco.com/go/ smallbizsupport. For technical documentation and other links, see Where to Go From Here, page 9. Returning the Switch to the Factory
Summary of the content on the page No. 10
Where to Go From Here 5 Support Cisco Small Business Support www.cisco.com/go/smallbizsupport Community Online Technical Support and www.cisco.com/support Documentation (Login Required) Phone Support Contacts www.cisco.com/en/US/support/tsd_cisco_ small_business_support_center_contacts.html Software Downloads Go to tools.cisco.com/support/downloads, (Login Required) and enter the model number in the Software Search box. Product Documentation Cisco Small Business SLM www.cisco.com/en/US/partne
Summary of the content on the page No. 11
10 Cisco Small Business SLM Series Smart Switch Installation Guide
Summary of the content on the page No. 12
Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner
