Summary of the content on the page No. 1
™
OmniView
KVM Switch
Control up to four computers from one PS/2 console
belkin.com
Belkin Corporation
501 West Walnut Street
Compton • CA • 90220 • USA
Tel: 310.898.1100
Fax: 310.898.1111
Belkin Components, Ltd.
Express Business Park • Shipton Way • Rushden
NN10 6GL • United Kingdom
Tel: +44 (0) 1933 35 2000
Fax: +44 (0) 1933 31 2000
Belkin Components B.V.
Starparc Building • Boeing Avenue 333
1119 PH Schiphol-Rijk • The Netherlands
Tel: +31 (0) 20 654 7300
Fax: +31 (0) 20 654 7349
Belkin Comp
Summary of the content on the page No. 2
TABLE OF CONTENTS INTRODUCTION Congratulations on your purchase of this Belkin OmniView SE Plus Series KVM Switch (the Switch). Our diverse line of KVM solutions exemplifies the Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Belkin commitment to delivering high-quality, durable products at a Overview reasonable price. Designed to give you control over multiple computers and Feature Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
OVERVIEW OVERVIEW OmniView SE Plus Series KVM Switches allow you to control up to a Direct-Access Port Selectors maximum of 16 computers with one keyboard, monitor, and mouse. They Direct-access port selectors, located conveniently on the front face support PS/2 input devices (keyboard and mouse) as well as VGA, SVGA, of the Switch, allow for simple, manual port-selection. Each button XGA, and XGA-2 video. controls a port. The BANK scroll buttons located on the front panel It supports both PS/2
Summary of the content on the page No. 4
OVERVIEW OVERVIEW Equipment Requirements Operating Systems Cables OmniView SE Plus Series KVM Switches are for use on CPUs using: Platforms To connect to the Switch, each PS/2 computer requires one VGA cable, • Windows® 95, 98, 2000, Me, NT®, XP one PS/2 keyboard cable, and one PS/2 mouse cable. Keyboard and mouse cables must have PS/2 male-to-PS/2 male connectors. Each USB computer • DOS requires one VGA cable and one USB A-to-B cable. • Turbolinux® and all Linux® distributions Video resolution
Summary of the content on the page No. 5
OVERVIEW OVERVIEW Unit Display Diagrams The Front of the OmniView SE Plus Series KVM Switch: The Back of the OmniView SE Plus Series KVM Switch: AutoScan button LED for selected port 7-segment LED for Computer USB port Console VGA Computer VGA port Flash upgrade port identification selected BANK identification Slave Input Master Input/Slave Output Console PS/2 mouse/keyboard ports DC power jack Master Input/Slave Output Computer PS/2 Manual BANK scroll Direct-access mouse/keyboard ports butto
Summary of the content on the page No. 6
OVERVIEW INSTALLATION Specifications Pre-Configuration Part No.: F1DZ102T, F1DZ104T Where to Place the Switch The enclosure of the OmniView SE Plus Series KVM Switch is designed Power: 12V DC, 1A AC power adapter with center-pin positive polarity for standalone or rack-mount configuration. An optional Rack-Mount Kit Daisy-Chain: Maximum of 4 KVM switches (F1D005) is available for use with the 4-Port KVM Switch. PCs Supported: 2 (F1DZ102T) Consider the following when deciding where to place the
Summary of the content on the page No. 7
INSTALLATION INSTALLATION Single KVM Switch Installation Step-by-Step Installation Guide This section provides complete instructions for the hardware setup of Cautions and Warnings a single SE Plus Series KVM Switch. Before attempting to connect anything to the Switch or your computers, please ensure that all equipment is powered off. Plugging and unplugging PS/2 Installation: cables while computers are powered on may cause irreversible damage to Keyboard, Video, and Mouse Connections the compu
Summary of the content on the page No. 8
INSTALLATION INSTALLATION Connect the Computer USB Installation PS/2 Installation Boot the computer you wish to connect via USB as you would normally 1. Using an OmniView KVM Cable (F3X1105-XX or F3X1835-XX-GLD), plug with the keyboard, monitor, and mouse connected directly to the in the male VGA connector to the VGA port on the computer. Connect computer. After the operating system finishes loading, connect the the other end (the female connector) of the VGA cable to the back of Switch to the U
Summary of the content on the page No. 9
INSTALLATION INSTALLATION Connecting Multiple KVM Switches (Daisy-Chaining) DIP Switch Configuration Chart You can daisy-chain up to four OmniView SE Plus Series KVM Switches together, giving a server administrator control over a maximum of 16 DIP SWITCH# BANK ADDRESS computers. When daisy-chained together, each unit is referred to as a 123 4 5 6 “BANK” and assigned an address. The Console keyboard, mouse, and ON ON ON ON ON ON BANK 00 MASTER (default) monitor connect to BANK 00 and are referred
Summary of the content on the page No. 10
INSTALLATION INSTALLATION Note: If the Switches do not enumerate correctly, reset the Master switch Installation (BANK 00) by simultaneously pressing the “BANK Up” and “BANK Down” Before you begin: buttons. You can also reset the Master switch to detect newly added Slave 1. Make sure that all computers are powered off and that each Switch switches. If the switches still do not enumerate correctly, check that all has been assigned a unique BANK address. switches have the correct BANK address assi
Summary of the content on the page No. 11
USING YOUR SWITCH USING YOUR SWITCH Select connected computers by either the direct-access port-selectors, You can switch directly to any port by entering the two-digit BANK address located on the front panel of the Switch, or hot key commands, through followed by the two-digit number of the port you wish to access. For the console keyboard. It takes approximately 1-2 seconds for the video example, if you press “Scroll Lock”, “Scroll Lock”, “00”, “02”, the Switch signal to refresh after switchin
Summary of the content on the page No. 12
USING YOUR KVM SWITCH USING YOUR KVM SWITCH AutoScan Mode Connecting Computers Pressing the AutoScan button on the Switch will activate the AutoScan 1. Connect a keyboard, monitor, and mouse to the computer you prepared function. In AutoScan mode, the Switch remains on one port for 10 for firmware updates. It must run Windows XP, 2000, NT, 95, 98, or Me. seconds, before switching to the next computer. This time interval cannot 2. Connect the power adapter to the Switch. be adjusted. 3. Connect
Summary of the content on the page No. 13
FAQs FAQs Q: What operating systems does the Switch support? Q: What is the maximum video resolution that the Switch supports? A: The Switch will support any operating system that runs on a PS/2 A: The advanced video circuit in the Switch supports a maximum TM and USB platform. It will also work with non-USB Sun and Mac® resolution of 2048x1536@85Hz. operating systems using the appropriate adapters (OmniView PS/2 Sun Adapter F1D082, OmniView PS/2 Mac Adapter F1D080). Operating Q: What video ba
Summary of the content on the page No. 14
FAQs TROUBLESHOOTING General Q: Can I use the Switch on my Sun computer that supports USB? A: Yes, the Switch works with any USB-capable computer. My computer does not boot when connected to the Switch but works fine when I connect the keyboard, video, and mouse directly to the computer. Q: Does the Switch support serial mice and keyboards? • Make sure that the keyboard and mouse cables are connected tightly A: Yes, the Switch supports serial devices (serial adapter required). between the Switch
Summary of the content on the page No. 15
TROUBLESHOOTING TROUBLESHOOTING The computer boots up, but the mouse does not work. Keyboard The computer does not detect a keyboard and I get a keyboard error • Make sure the mouse is plugged in properly. reported at boot-up. • Make sure the mouse works when directly plugged into the computer. • Check that the keyboard cable between the Switch and the computer is Rebooting may be necessary when trying this. completely connected. Tighten any loose connections. • Try a different mouse. • Try usi
Summary of the content on the page No. 16
WARRANTY, FCC, CE, ICES STATEMENT FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the products: F1DZ102T, F1DZ104T to which this declaration relates: Comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference re
