Summary of the content on the page No. 1
Unpack
Avaya P333T
1
Quick Start Guide
Rack mount (optional)
2
Power up
3
Connect the cables
4
Configure
5
Run Web-based
Manager (optional)
6
Summary of the content on the page No. 2
Unpack Check the package contents for the following: ! If any items are missing or damaged, contact your supplier. 1 Equipment • One Avaya P333T Layer 2 Workgroup Switch One AC power cable One RJ-45 to DB-9 serial adapter cable Four rubber feet Four screws with washers for rack mounting ! Ethernet connection cables are not supplied Documentation Avaya P333T Quick Start Guide (this document) Avaya P330 Release Notes Avaya P330 Documentation and Utilities CD (see detail below) Avay
Summary of the content on the page No. 3
Rack mount (optional) WARNING: Disconnect all cables from the unit before proceeding with the rack installation. 1. Snap open the hinged ends of the unit’s front panel to reveal the screw holes. Closed hinged end 2 P333T 51 52 53 54 55 56 57 58 1 23 4 5 6 7 8 9 10 11 12 EXPANSION SLOT 59 60 61 62 63 64 65 66 13 14 15 16 17 18 19 20 21 22 23 24 LNK COL Tx Rx FDX FC Hspd LAG SYS OPR PWR FIV LAG LAG LAG 1 23 4 5 6 78 9 10 11 12 CONSOLE 13 14 15 16 17 18 19 20 21 22 23 24 Open hinged end P333T 51 52
Summary of the content on the page No. 4
Power up Avaya P330 AC Version 1. Insert the power cord into the power connector (BUPS or Power Supply) on the rear of the unit. BUPS connector AC connector 2. Insert the other end of the power cord into the electricity supply or the BUPS connector. ! The unit powers up and performs a self test procedure. The LEDs flash at regular intervals after the self-test procedure is completed successfully. Avaya P330 DC Version 3 WARNING: Before performing any of the following procedures, ensure that DC
Summary of the content on the page No. 5
Connect the cables Connect PCs, servers, routers, workstations, and hubs 1. Connect the Ethernet connection cable (not supplied) to a 10/100 Mbps port on the front panel of the Avaya P330. ! You should use standard RJ-45 connections. You must use CAT-5 cable for 100 Mbps operation. 2. Connect the other end of the cable to the Ethernet port of the PC, server, router, worksta- tion, switch or hub. ! Use a cross cable when connecting the Avaya P330 to a switch or hub. 3. Check that the appropriate
Summary of the content on the page No. 6
Basic configuration To connect a PC terminal or VT-100 terminal to the Avaya P330 1. If you are using a PC, initiate a VT-100 terminal emulation session using an application such as Windows® HyperTerminal. 2. Press Enter. 3. Type the User name root when prompted and press Enter. 4. Type the default password root when prompted and press Enter. ! The P330-N(super)# prompt appears. !N is the number of the switch in the stack. Assigning the Stack IP Address ! Commands are shown as follows: set inter
Summary of the content on the page No. 7
Setting the Parameters If you wish to change the default parameters shown and configure the mandatory parameters, we recommend that you use the Command Line Interface (CLI). ! For further information, please refer to Chapter 6 of the Avaya P330 User’s Guide. Default Switch Parameters Configuration Parameter Default Setting Avaya P330 IP Address 149.49.32.134 BootP Mode Never Default Gateway 0.0.0.0 Management PC SLIP IP Address 192.168.10.2 VLAN Management ID 1 Spanning Tree Enabled TFTP Mode L
Summary of the content on the page No. 8
Run the Web-Based Manager (optional) ! To configure the Avaya P330 you can use the P330 Web-based Manager in addition to using the CLI. System Requirements Minimum hardware and Operating System requirements are: Pentium® II 400 Mhz-based computer with 128 Mb of RAM Screen resolution of 1024 x 768 pixels Microsoft® Internet Explorer® 5 or Netscape Navigator® 4.x Windows® 95, NT® 4.0 (server/workstation) or Windows 2000 (server/workstation) Sun Microsystems Java™ plug-in version 1.2.2
Summary of the content on the page No. 9
! If the network manager has configured the system the plug-in should be installed auto- matically. If the plug-in is not installed automatically, there are three ways to install the plug-in manually: Either install the plug-in from the CD as follows: 1. Close all unnecessary applications on your PC. 2.Insert the “Avaya P330 Documentation and Utilities” CD in the CD drive. 3.Click Start on the Task bar. 4.Select Run. 5.Type x:\emweb-aux-files\plugin_1_2_2.exe (where x: is the CD drive letter
Summary of the content on the page No. 10
Documentation and Online Help Refer to the Avaya P330 Documentation and Utilities CD for full instructions.
Summary of the content on the page No. 11
Notes
Summary of the content on the page No. 12
Contact Information To contact Avaya technical support: From the United States: Please call 1-800-237-0016, press 0, then press 73300. From outside the United States: EMEA (Europe, Middle East and Africa). Email: csctechnical@avaya.com Country Local Dial-In Number Country Local Dial-In Number Country Local Dial-In Number Albania +31 70 414 8001 Ireland +353 160 58 479 Qatar +31 70 414 8059 Austria +43 1 36 0277 1000 Israel +1 800 93 00 900 Portugal +351 21 318 0047 Azerbadjan +31 70 414 8047
