Summary of the content on the page No. 1
By
MONO CHANNEL / 2 CHANNEL / 4 CHANNEL
AUTOMOTIVE AMPLIFIER
T-1000M
T-270 / T-2100 / T-2130
T-460 / T-480
INSTRUCTION MANUAL
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Congratulations on your Purchase Your new high fidelity bridgeable/stereo amplifier is designed to deliver maximum enjoy ment and one year of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble free installation. Features • Four Class ''AB'' High-Current Dual Discrete Drive Stages. • Class ''AB'' Technology MOSFET PWM Power Supply. • Bridgeable & TRI-Mode Operation. • Continuously Vari
Summary of the content on the page No. 4
• NEVER operate the amplifier without the proper power and ground wire, 10 gauge minimum. • NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery. This fuse is to protect the car not the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other than the recommended fuse ratings at the battery and at the amplifier may cause damage to the amplifier and will void your warranty. • Do not
Summary of the content on the page No. 5
INSTALLATION MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface in this manner. 3. Remove amplifier. Drill four 3.5 m/m holes into mounting surface. If you want to mount the ampl
Summary of the content on the page No. 6
CONNECTIONS INPUT CONNECTIONS This amplifier will accept low level inputs only. Low level is the same as line level. The low level signal is carried through RCA cables. It is preferred to use low level inputs to the amplifier if the head unit is equipped with the low level outputs. If not, you can use a "high to low converter" available through your local car audio shop. Connect the low level/line level RCA cables from the head unit, or signal processor, to the line level input on the ampli
Summary of the content on the page No. 7
MONO CHANNEL SYSTEM WIRING DIAGRAM LINE IN REMOCON LINE OUT GAIN PHASE BASS L.P.F CH1 CH1 O O 6V 0.2V 0 180 0dB 12dB 50Hz 250Hz CH2 CH2 CH1 CH2 GND REM B+ CAR STEREO HEAD UNIT FIG.2 5 AUTO - ANTENNA LEAD
Summary of the content on the page No. 8
2 CHANNEL SYSTEM WIRING DIAGRAM LINE IN REMOCON LINE OUT GAIN BASS L.P.F H.P.F CH1 CH1 L.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz 80Hz 1.2KHz FLAT CH2 CH2 CROSSOVER CH1 CH2 GND REM B+ CAR STEREO HEAD UNIT FIG.2 6 AUTO - ANTENNA LEAD
Summary of the content on the page No. 9
4 CHANNEL SYSTEM WIRING DIAGRAM LINE IN CROSSOVER CROSSOVER LINE IN GAIN BASS BASS GAIN CH1 CH3 L.P.F H.P.F H.P.F L.P.F 6V 0.2V 0dB 12dB FLAT 50Hz 500Hz 50Hz 500Hz FLAT 0dB 12dB 6V 0.2V CH2 CH4 CH 1/2 CH 3/4 CH1 CH2 CH3 CH4 GND REM B+ CAR STEREO HEAD UNIT FIG.2 7 AUTO - ANTENNA LEAD
Summary of the content on the page No. 10
SPEAKER CONNECTIONS This amplifier can operate in one, two or three channel mode. The minimum impedance for single channel (bridged/mono) operation is 4 or 8 ohms. Tri channel power is referred to stereo and mono at the same time. Minimum impedance remains the same for three channel (front /subwoofer) systems as long as proper passive crossovers are used. Connect right and left speaker wire to corresponding speaker output terminals of the amplifier. Be sure to have the positive wire from th
Summary of the content on the page No. 11
SPEAKER CONNECTIONS 2 CH SPEAKER WIRING DIAGRAM 1 SPEAKER BRIDGED CH1 CH2 POWER FUSE GND REM B+ BRIDGED SPEAKER ON PROTECT 4 - 8 Ohm 1CH 2 SPEAKER STEREO POWER CH1 CH2 FUSE GND REM B+ BRIDGED SPEAKER ON PROTECT 2 - 4 Ohm 1 CH 2 CH 3 SPEAKER TRI MODE POWER CH1 CH2 FUSE GND REM B+ BRIDGED SPEAKER ON PROTECT 4 - 8 Ohm 1 CH 2 CH 3 CH 4 - 8 Ohm WOOFER 2CH+1CH FIG.3 9
Summary of the content on the page No. 12
SPEAKER CONNECTIONS 4 CH SPEAKER WIRING DIAGRAM 2 SPEAKER BRIDGED CH1 CH2 POWER CH3 CH4 FUSE BRIDGED GND REM B+ SPEAKER ON PROTECT 4-8 Ohms 2 CH 1 CH 2 SPEAKER + 1 SUBWOOFER CH1 CH2 POWER CH3 CH4 FUSE BRIDGED GND REM B+ SPEAKER ON PROTECT 2-4 Ohms 3 CH 2-4 Ohms 1CH 2 CH SUB WOOFER 4-8 Ohms 4 SPEAKER STEREO CH1 CH2 CH3 CH4 POWER FUSE GND REM B+ BRIDGED SPEAKER ON PROTECT 2-4 Ohms 1 CH 3 CH 4 CH 2 CH 6 SPEAKER HEX MODE CH1 CH2 POWER CH3 CH4 FUSE GND REM B+ BRIDGED SPEAKER ON
Summary of the content on the page No. 13
ADJUSTMENTS 1.Set to the "H.P.F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz & 50Hz to 500Hz as the crossover point. 2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB /
Summary of the content on the page No. 14
FRONT/REAR PANEL 2CHANNEL LINE IN LINE OUT GAIN BASS L.P.F H.P.F CH1 CH1 L.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz 80Hz 1.2KHz FLAT CH2 CH2 CROSSOVER T-270,T-2100 POWER CH1 CH2 FUSE GND REM B+ 30A BRIDGED SPEAKER ON PROTECT TUNN T-270 By T-270 POWER CH1 CH2 FUSE GND REM B+ BRIDGED 25A 25A SPEAKER ON PROTECT TUNN T-2100 By T-2100 LINE IN REMOCON LINE OUT GAIN BASS L.P.F H.P.F CH1 CH1 L.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz 80Hz 1.2KHz FLAT CH2 CH2 CROSSOVER T-2130 POWER CH1
Summary of the content on the page No. 15
FRONT/REAR PANEL 4CHANNEL LINE IN CROSSOVER CROSSOVER LINE IN GAIN BASS BASS GAIN CH1 CH3 L.P.F H.P.F H.P.F L.P.F 6V 0.2V 0dB 12dB FLAT 50Hz 500Hz 50Hz 500Hz FLAT 0dB 12dB 6V 0.2V CH2 CH4 CH 1/2 CH 3/4 T-460, T-480 CH1 CH2 POWER CH3 CH4 FUSE BRIDGED BRIDGED GND REM B+ 30A SPEAKER ON PROTECT TUNN T-460 By T-460 CH1 CH2 POWER CH3 CH4 FUSE BRIDGED GND REM B+ 25A 25A SPEAKER ON PROTECT TUNN T-480 By T-480 MONO CHANNEL LINE IN REMOCON LINE OUT GAIN PHASE BASS L.P.F CH1 CH1 O O 6V 0.2V 0
Summary of the content on the page No. 16
TROUBLE SHOOTING GUIDE. This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly. SYMPTOM PROBABLE CAUSE SOLUTION No Audio Low or N.C Remote Check remote turn-on voltage at Turn-on connections amp and head unit Blown Fuse Replace with new fa
Summary of the content on the page No. 17
SPECIFICATI SPECIFICATION ON Output Power Rating RMS T-270 T-2100 T-2130 Channel 2CH 2CH 2CH Total Max Power 900 Watts 1200 Watts 1500 Watts 4 Ohm at 14.4V 0.3%THD ( RMS ) 100W x 2 150W x 2 200W x 2 4 Ohm at 14.4V ( MAX ) 180W x 2 290W x 2 340W x 2 2 Ohm at 14.4V 0.3%THD ( RMS ) 160W x 2 250W x 2 310W x 2 2 Ohm at 14.4V ( MAX ) 250W x 2 400W x 2 500W x 2 N / A N / A N / A 1 Ohm at 14.4V 0.3%THD Mono Bridge ( RMS ) 310W x 1 490W x 1 630W x 1 Power Supply Full PWM Full PWM Full PWM Output P
Summary of the content on the page No. 18
SPECIFICATI SPECIFICATION ON Output Power Rating RMS T-1000M T-460 T-480 Channel 1CH Mono 4CH 4CH Total Max Power 1200 Watts 800 Watts 1000 Watts 4 Ohm at 14.4V 0.3%THD ( RMS ) 330W x 1 50W x 4 80W x 4 4 Ohm at 14.4V ( MAX ) 630W x 1 120W x 4 130W x 4 2 Ohm at 14.4V 0.3%THD ( RMS ) 510W x 1 85W x 4 110W x 4 2 Ohm at 14.4V ( MAX ) 1000W x 1 130W x 4 190W x 4 N / A N / A N / A 1 Ohm at 14.4V 0.3%THD Mono Bridge ( RMS ) N / A 170W x 2 220W x 2 Power Supply Full PWM Full PWM Full PWM Output Power
Summary of the content on the page No. 19
WARRANTY WARRANTY LIMITATIONS WARRANTY TERMS The following is NOT covered under TUNN () Effective April 1st. 2008 warranty program: These terms supersede all prior published warranty terms 1. Product owned by anyone other than the TUNN products are warrantied against original purchaser from an authorized defects in materials and workmanship for TUNN dealer. a period of One (1) Year from the original (The warranty is NOT transferable and date of purchase. will not apply to products purcha
Summary of the content on the page No. 20
10110 Santa Fe Springs Road Santa Fe Springs, CA 90670 1-562-926-2600
