Summary of the content on the page No. 1
Powered by Accton
ES4524M-PoE
L2/4 Gigabit Ethernet Switch
with Power-over-Ethernet Installation Guide
www.edge-core.com
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Installation Guide L2/4 Gigabit Ethernet Switch Layer 2 Standalone Switch with 24 10/100/1000BASE-TX (RJ-45) Ports providing Power-over-Ethernet, and 2 Gigabit Combination Ports (RJ-45/SFP)
Summary of the content on the page No. 4
ES4524M-PoE E122007-LP-R01 149100037400A
Summary of the content on the page No. 5
Compliances and Safety Warnings FCC - Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful int
Summary of the content on the page No. 6
Safety Compliance Warning: Fiber Optic Port Safety When using a fiber optic port, never look at the transmit laser while it is CLASS I powered on. Also, never look directly at the fiber TX port and fiber cable LASER DEVICE ends when they are powered on. Avertissment: Ports pour fibres optiques - sécurité sur le plan optique Ne regardez jamais le laser tant qu'il est sous tension. Ne regardez DISPOSITIF LASER jamais directement le port TX (Transmission) à fibres optiques et les DE CLASSE I
Summary of the content on the page No. 7
Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following: Power Cord Set U.S.A. and Canada The cord set must be UL-approved and CSA certified. The minimum specifications for the flexible cord are: - No. 18 AWG - not longer than 2 meters, or 16 AWG. - Type SV or SJ - 3-conductor The cord set must have a rated current capacity of at least 10 A The attachment plug must be an earth-grounding type with NEMA 5-15P (15
Summary of the content on the page No. 8
France et Pérou uniquement: Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec raccordement direct à la terre (masse). Cordon électrique - Il doit être agréé dans le pays d’utilisation Etats-Unis et Canada: Le cord
Summary of the content on the page No. 9
Environmental Statement The manufacturer of this product endeavors to sustain an environmentally-friendly policy throughout the entire production process. This is achieved though the following means: • Adherence to national legislation and regulations on environmental production standards. • Conservation of operational resources. • Waste reduction and safe disposal of all harmful un-recyclable by-products. • Recycling of all reusable waste content. • Design of products to maximize recyclables
Summary of the content on the page No. 10
x
Summary of the content on the page No. 11
About This Guide Purpose This guide details the hardware features of the switch, including the physical and performance-related characteristics, and how to install the switch. Audience The guide is intended for use by network administrators who are responsible for installing and setting up network equipment; consequently, it assumes a basic working knowledge of LANs (Local Area Networks). Conventions The following conventions are used throughout this guide to show information: Note: Emphasize
Summary of the content on the page No. 12
xii
Summary of the content on the page No. 13
Contents Chapter 1: About the ES4524M-PoE 1-1 Overview 1-1 Switch Architecture 1-1 Power-over-Ethernet Capability 1-2 Network Management Options 1-2 Description of Hardware 1-2 10/100/1000BASE-T Ports 1-2 SFP Slots 1-3 Port and System Status LEDs 1-3 Power Supply Socket 1-4 Features and Benefits 1-4 Connectivity 1-4 Expandability 1-5 Performance 1-5 Management 1-5 Chapter 2: Network Planning 2-1 Introduction to Switching 2-1 Application Examples 2-1 Collapsed Backbone 2-1 Network Aggregation Pla
Summary of the content on the page No. 14
Contents Chapter 4: Making Network Connections 4-1 Connecting Network Devices 4-1 Twisted-Pair Devices 4-1 Power-over-Ethernet Connections 4-1 Cabling Guidelines 4-1 Connecting to PCs, Servers, Hubs and Switches 4-2 Network Wiring Connections 4-2 Fiber Optic SFP Devices 4-3 Connectivity Rules 4-5 1000BASE-T Cable Requirements 4-5 1000 Mbps Gigabit Ethernet Collision Domain 4-5 100 Mbps Fast Ethernet Collision Domain 4-6 10 Mbps Ethernet Collision Domain 4-6 Cable Labeling and Connection Records
Summary of the content on the page No. 15
Contents Index xv
Summary of the content on the page No. 16
Contents xvi
Summary of the content on the page No. 17
Tables Table 1-1 Port Status LEDs 1-3 Table 1-2 System Status LEDs 1-4 Table 3-1 Serial Cable Wiring 3-7 Table 4-1 Maximum 1000BASE-T Gigabit Ethernet Cable Length 4-5 Table 4-2 Maximum 1000BASE-SX Fiber Optic Cable Length 4-5 Table 4-3 Maximum 1000BASE-LX Fiber Optic Cable Length 4-5 Table 4-4 Maximum 1000BASE-ZX Fiber Optic Cable Length 4-5 Table 4-5 Maximum Fast Ethernet Cable Length 4-6 Table 4-6 Maximum Ethernet Cable Length 4-6 Table A-1 Troubleshooting Chart A-1 Table B-1 10/100BASE-TX MD
Summary of the content on the page No. 18
Figures Figure 1-1 Front Panel 1-1 Figure 1-2 Rear Panel 1-1 Figure 1-3 Port and System LEDs 1-3 Figure 1-4 Power Supply Sockets 1-4 Figure 2-1 Collapsed Backbone 2-2 Figure 2-2 Network Aggregation Plan 2-2 Figure 2-3 Remote Connections with Fiber Cable 2-3 Figure 2-4 Making VLAN Connections 2-4 Figure 3-1 RJ-45 Connections 3-2 Figure 3-2 Attaching the Brackets 3-3 Figure 3-3 Installing the Switch in a Rack 3-4 Figure 3-4 Attaching the Adhesive Feet 3-4 Figure 3-5 Inserting an SFP Transceiver in
Summary of the content on the page No. 19
Chapter 1: About the ES4524M-PoE Overview The ES4524M-PoE is an intelligent Layer 2 PoE switch with 24 10/100/1000BASE-T * ports, two of which are combination ports that are shared with two SFP transceiver slots (see Figure 1-1, Ports 23-24). The switch includes an SNMP-based management agent embedded on the main board, which supports both in-band and out-of-band management access. It can easily enhance your network with full support for Spanning Tree Protocol, multicast switching, and virtu
Summary of the content on the page No. 20
About the ES4524M-PoE 1 a buffer and checked for validity before being forwarded. This prevents errors from being propagated throughout the network. Power-over-Ethernet Capability The switch’s 24 10/100/1000 Mbps ports support the IEEE 802.3af Power-over-Ethernet (PoE) standard that enables DC power to be supplied to attached devices using wires in the connecting Ethernet cable. Any 802.3af compliant device attached to a port can directly draw power from the switch over the Ethernet cable
