Summary of the content on the page No. 1
i
HFi100.2 / HFi55.4 / HFi100.4
HFi1000D / HFi1500D
HFi2000D / HFi2500D
Summary of the content on the page No. 2
HFi HIGH PERFORMANCE AMPLIFIERS The HFi Series products have been designed to a very high level of performance, with features unavailable in any other product. All of the amplifiers have variable crossovers built in, with added touches such as subsonic filter, bass equalization and a remote Level control module(some models) that allows subwoofer Level control from the drivers seat. To ensure years of listening pleasure, all amplifiers have a built in diagnostic mode that will detect shorted s
Summary of the content on the page No. 3
WIRE GAUGE GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion. Lower power amplifiers w
Summary of the content on the page No. 4
AMPLIFIER FEATURE DESCRIPTIONS HFi AMPLIFIERS: ! Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation ! All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, except the mono amps which are capable of 4, 2 and 1-Ohm loads. and amplifier DC faults indicated by the red “PROTECT” LED. ! Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable ! CAUTION: DO NOT OPERATE ANY AMPL
Summary of the content on the page No. 5
OUTPUT INPUT OUTPUT INPUT LEVEL BASS EQ X-OVER HPF LPF MODE POWER LEVEL BASS EQ X-OVER HPF LPF MODE POWER L L L L PROTECT PROTECT 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 12KHz 30Hz 250Hz MONO STEREO 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 12KHz 30Hz 250Hz MONO STEREO R R
Summary of the content on the page No. 6
LEVEL BASS EQ X-OVER HPF LPF LEVEL BASS EQ X-OVER HPF LPF CH3/4 CH1/2 POWER LINE OUT CH3/4 CH1/2 POWER LINE OUT PROTECT PROTECT 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 12KHz 30Hz 250Hz 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 12KHz 30Hz 250Hz R R R R LEVEL BASS EQ X-OVER HPF LPF MODE LEVEL BASS EQ
Summary of the content on the page No. 7
LEVEL BASS EQ X-OVER HPF LPF POWER CH3/4 CH1/2 LINE OUT PROTECT 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 12KHz 30Hz 250Hz R R LEVEL BASS EQ X-OVER HPF LPF MODE L L 6V 0.2V 0dB 12dB FULL LPF HPF 60Hz 12KHz 30Hz 250Hz 2 3 4 OUTPUT INPUT LEVEL BASS EQ X-OVER HPF LPF MODE
Summary of the content on the page No. 8
OUTPUT INPUT OUTPUT INPUT LEVEL BASS EQ REMOTE SUBSONIC LOW PASS LEVEL BASS EQ REMOTE SUBSONIC LOW PASS POWER L L POWER L L PROTECT PROTECT 6V 0.2V 0dB 10dB 15Hz 35Hz 30Hz 250Hz 6V 0.2V 0dB 10dB 15Hz 35Hz 30Hz 250Hz R R R
Summary of the content on the page No. 9
7
Summary of the content on the page No. 10
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE HFi100.2 / HFi55.4 / HFi100.4 General: At this point you are ready to get more specific on the settings for your amplifier. High Pass: -When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 100Hz, the amplifier
Summary of the content on the page No. 11
TROUBLESHOOTING A SYSTEM The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the PROTECT system built into all Hifonics amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A sort circuit on the loudspeaker le
Summary of the content on the page No. 12
Maxxsonics Limited Warranty As the manufacturer of Maxxsonics, MB Quart, Autotek, Crunch and Hifonics car audio products, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one (1) Year from date of purchase. All other parts and accessories of the system are warrantied to be free from defects in material and workmanship for one (1) year from date of purchase. Maxxsonics will repair or replace at it’s option and f
Summary of the content on the page No. 13
OEM Integration Accessories MX-1 Premium High To Low Level Converter MX-3 Bass Controller * Converts High Level OEM speaker wires to Ultra Clean RCA Low Level Outputs * High Level Inputs: Accepts all types of High level Inputs * Parametric Bass EQ: Provides a wide array of subwoofer output signal including floating ground and high voltages up to 30 volts. shaping controls to enhance bass response and sound quality including * Audio Signal Sense / Hardwire Turn-On: Audio sense detec
Summary of the content on the page No. 14
Accessories 5V ON SLAVE 3V 7V OFF MASTER 35Hz 250Hz 1V 9V 15Hz 35Hz MODE LOW PASS RED - CLIP OUTPUT TEST TONE SUBSONIC GREEN - 9V 65Hz FILTER LEVEL FILTER 24 dB/OCT 24 dB/OCT MAXX-LINK MLX-100 9V 0.2V 0 180 0dB +10 dB 30Hz 100Hz INPUT PHASE BOOST BANDWIDTH FREQUENCY LEVEL PARAMETRIC BASS EQ -6dB BYPASS RED - CLIP GREEN - 9V -20dB 0dB NORMAL LEVEL 12
Summary of the content on the page No. 15
PART#: A1109
