Summary of the content on the page No. 1
Model 6000
Owner’s Guide
This device complies with part 15 of FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including inter-
ference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
device.
Summary of the content on the page No. 2
Table of Contents System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Your Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 What Is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Transmitter Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 3
What is included ■ The control module ■ A pair of two-button transmitters ® ® ■ A Stinger DoubleGuard dual-output shock sensor ® ® ■ The Revenger Soft Chirp six-tone programmable siren ■ The red Status LED indicator light ® ■ A push-button Valet switch ■ Your warranty card ® ■ FailSafe starter kill (Ready feature, may require additional labor). CONGRATULATIONS on your purchase of a state-of-the-art vehicle securi- ty system. This system has been designed to provide years of trouble- free operati
Summary of the content on the page No. 4
Transmitter Channels LED Button I Button II Button III Channel I The arm/disarm and panic functions, are usually controlled by Button I. Channel II ™ The Silent Mode /trunk release function, is usually controlled by Button II. ™ ® Silent Mode and Remote Valet work by pressing button II for less than one second. Trunk release requires you to press Button II for 1.5 seconds. Channel III (for options) Usually controlled by pressing Buttons I and II at the same time. These assignments can be chan
Summary of the content on the page No. 5
Using Your System Arming You can turn on, or arm, the system by pressing button I of your transmitter for one second. When the system arms, you will hear a short siren sound, or chirp, and see the parking lights flash once. If the vehicle’s power door locks are controlled by the system, the doors will lock. While the system is armed, the Status LED will flash about twice a second, showing that the system is actively protecting your vehicle. If you hear a sec- ond chirp after arming and see the S
Summary of the content on the page No. 6
to disarm the system with your transmitter if you inadvertently open the door while the system is armed, while still providing instant response (even if the door is immediately closed). • Turning on the ignition key will trip the same two-stage response as opening a door. • The optional starter kill prevents the vehicle’s starter from cranking. Arming While Driving Your system can be armed while driving the vehicle! Simply press button I on your transmitter while the vehicle is running. The sys
Summary of the content on the page No. 7
to check the vehicle visually. The trigger will stop, but the vehicle will remain protected. To disarm with the transmitter during a trigger, press Button I on your transmitter. The siren will stop sounding. Next press Button I once more and the system will chirp four or five times (reporting the trigger) and disarm. Disarming Without a Transmitter This feature allows you to disarm the system without the transmitter should it be lost, damaged or disabled. In order to disarm without a transmitter
Summary of the content on the page No. 8
® Valet Mode You can prevent your system from automatically arming and triggering by ® using Valet Mode. This is very useful when washing the vehicle or having it ® serviced. In Valet Mode, the system will not arm, even with the transmitter, but all convenience functions (door locks, trunk release, etc.) will work normally. ® ® To enter or exit Valet Mode with the Valet switch: Turn ignition to "run" position, then turn to "off" posi- ® tion. Press and release the Valet switch within 10 sec- ond
Summary of the content on the page No. 9
trigger the system while it is being bypassed, the 60-minute bypass period will start over. This ensures that a sensor that continuously triggers will remain bypassed. ™ Doors are covered by NPC differently: If the alarm is triggered by an open door for three full cycles (one and one half minutes), the doors will be by- passed until the trigger ceases. NOTE: Arming and disarming the system does not reset this function! The only ways to reset a bypassed zone are for it to not trigger for 60 minut
Summary of the content on the page No. 10
Diagnostics The microprocessor at the heart of your system is constantly monitoring all of the switches and sensors connected to it. It detects any faulty switches and sensors and prevents them from disabling the entire system. The micro- processor will also record and report any triggers that occurred during your absence. Arming Diagnostics If the system is armed with an input active (door open, sensor triggering, etc.) the unit will chirp once when arming and then one more time a few seconds l
Summary of the content on the page No. 11
Table of Zones The zone number is the number of LED flashes used by the system to iden- tify that input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. Zone (Number of LED Flashes) Description Dealer-Installed Options 1 Instant trigger—often used for hood/trunk pin switches 2 Instant trigger—a heavier impact ® detected by the Doubleguard Shock Sensor 3 Door switch trigger 4 Instant trigger—for optional sens
Summary of the content on the page No. 12
™ Code Hopping Explained The receiver and transmitters each use a mathematical formula called an algorithm to change their code each time the transmitter is used. This tech- nology has been developed to increase the security of the unit. The control unit knows what the next codes should be. This helps to keep the transmitter “in synch” with the control unit even if you use the remote control out of range of the vehicle. However, if the transmitter has been pressed many times out of range of the
Summary of the content on the page No. 13
NOTE: If the door is open when the ignition is turned on, the doors will not lock. • Panic mode enabled/disabled with the ignition on. (Some states have laws against siren capability in a moving vehicle). • Automatic Engine Disable (AED) on or off. The purpose of the feature is to pro- tect the vehicle from being stolen at all times, regardless of whether or not the alarm is armed. If AED is programmed on, the starter of the vehicle will be dis- abled 30 seconds after the ignition is turned off.
Summary of the content on the page No. 14
® Vehicle Recovery System (VRS )* The optional Vehicle Recovery System feature is designed to ensure that any unauthorized user of your vehicle (even if using your keys and remote con- trol) will not be able to permanently separate you from your vehicle. ® The VRS feature cannot prevent a carjacking attempt, however, it does ensure that if your vehicle is taken by an unauthorized user, it will be disabled (after several progressive warnings) as safely as possible. Should a carjack- ® ing occur,
Summary of the content on the page No. 15
® Arming the VRS ® To arm the VRS , push the button once. This can be done before driving or while driving the vehicle. Once the system is armed, it will go into its triggered sequence (see below) if any door is opened and closed. If you are forced from the vehicle the system will trigger as the door will be opened and closed as you leave the vehicle. This is how the system works to combat intersection ® carjacking. If ordered from the vehicle, you may press the VRS button before exiting. Arming
Summary of the content on the page No. 16
® From this point on, when the ignition key is turned off, the VRS ® will immediately turn on the FailSafe starter kill. This will pre- vent the vehicle from being restarted, thus immobilizing it at that spot. Three minutes after the constant siren output begins, the flashing parking lights and the siren will stop. The starter kill ® will remain active until the VRS system is disarmed. If the door is opened or the ignition is turned off and on in an attempt to restart the car, the siren and flas
Summary of the content on the page No. 17
Glossary of Terms Control Unit The “brain” of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which monitors your vehi- cle and controls all of the alarm's functions. ® FailSafe Starter Kill An automatic switch controlled by the security system which prevents the vehicle’s starter from cranking whenever the system is armed. The vehicle is never prevented from cranking when the system is dis- armed, in valet mode, or should the starter kill switch
Summary of the content on the page No. 18
Security & Convenience Expansions Here we have listed only some of the many expansion options available. Please consult your dealer for a complete explanation of all the options avail- able to you. Field Disturbance Sensor: An invisible dome of coverage is established by the 508T “radar” sensor.Your system can react to any intrusions into this field with the triggered sequence. Backup Battery: The 520T keeps the system armed, triggers the alarm and keeps the starter kill active if main battery
Summary of the content on the page No. 19
QUICK REFERENCE OPERATING CARD: Arming ▼ You can turn on, or arm, the system by pressing Button I of your transmitter for one second. When the system arms, you will hear a short chirp, and see the parking lights flash once. Arming While Driving ▼ Press Button I on your transmitter while the vehicle is running. The system will chirp once and then once more to indicate that the igni- tion is on. Disarming ▼ Press Button I. You will hear two chirps, and the parking lights will flash twice. High Sec
Summary of the content on the page No. 20
® The company behind DEI is Directed Electronics, Inc. Since its inception, the company known as Directed Electronics, Inc. ® (DEI ) has had one purpose - to bring the proven advantages of micro- processor and I.C. technology to the automotive industry. ® As a recipient of numerous patents, DEI has established new stan- dards in electronic design, automated manufacturing, and dealer sup- port. Its electronic products are sold and serviced worldwide. Call (800) 274-0200 for more information about
